TMPM330 - Keil

More documents

Recommendations

Info

Under development TMPM330 (rev 0.4)17-33 TMPM330 6. The 7 th byte indicates whether the Chip Erase command is normally completed or not. At normal completion, completion code (4FH) is sent. When an error was detected, error code (4CH) is sent. 7. The 9th byte is the next command code. Flash Memory Operation
5) Acknowledge Responses Under development TMPM330 (rev 0.4)17-34 TMPM330 The boot program represents processing states with specific codes. Table 17-11 to Table 17-14 show the values of possible acknowledge responses to the received data. The upper four bits of the acknowledge response are equal to those of the command being executed. Bit 3 of the code indicates a receive error. Bit 0 indicates an invalid command error, a checksum error or a password error. Bit 1 and bit 2 are always 0. Receive error checking is not done in I/O Interface mode. Table 17-11 ACK Response to the Serial Operation Mode Byte Return Value Meaning 0x86 The SIO can be configured to operate in UART mode. (See Note) 0x30 The SIO can be configured to operate in I/O Interface mode. Note: If the serial operation mode is determined as UART, the boot program checks if the SIO can be programmed to the baud rate at which the operation mode byte was transferred. If that baud rate is not possible, the boot program aborts, without sending back any response. Table 17-12 ACK Response to the Command Byte Return Value Meaning 0x?8 (See Note) A receive error occurred while getting a command code. 0x?1 (See Note) An undefined command code was received. (Reception was completed normally.) 0x10 The RAM Transfer command was received. 0x20 The Show Flash Memory Sum command was received. 0x30 The Show Product Information command was received. 0x40 The Chip Erase command was received. Note: The upper four bits of the ACK response are the same as those of the previous command code. Table 17-13 ACK Response to the Checksum Byte Return Value Meaning 0xN8 (See Note) A receive error occurred. 0xN1 (See Note) A checksum or password error occurred. 0xN0 (See Note) The checksum was correct. Note: The upper four bits of the ACK response are the same as those of the operation command code. It is 1 ( N=RAM transfer command data [7:4] ) when password error occurs. Table 17-14 ACK Response to Chip Erase Byte Return Value Meaning 54H The Chip Erase enabling command was received. 4FH The Chip Erase command was completed. 4CH The Chip Erase command was abnormally completed. Flash Memory Operation
Page 1 and 2:
1. Overview and Features Under deve
Page 3 and 4:
Under development (13) Standby mode
Page 5 and 6:
2. Pin Layout and Pin Functions Und
Page 7 and 8:
Pin No. Under development Table 2.1
Page 9 and 10:
Type Function Function/ BOOT Functi
Page 11 and 12:
Type Function/ Debug Function # of
Page 13 and 14:
2.3 Pin Names and Power Supply Pins
Page 15 and 16:
4. Memory map 4.1 Memory map 0x4008
Page 17 and 18:
0x4008 FFFF 0x4000 0000 0x2000 1FFF
Page 19 and 20:
X1 X2 XT1 XT2 5.2.2 Clock System Bl
Page 21 and 22:
SYSCR0 SYSCR1 SYSCR2 5.3.2 Detailed
Page 23 and 24:
STBYCR0 STBYCR1 STBYCR2 5.3.2.3 Sta
Page 25 and 26:
CKSEL 5.3.2.5 System Clock Selectio
Page 27 and 28:
5.4.2 Main System Clock External os
Page 29 and 30:
5.4.4 System Clock Pin Output Funct
Page 31 and 32:
5.8.1 IDLE Mode Under development T
Page 33 and 34:
Under development 5.8.4 Low power C
Page 35 and 36:
5.8.7 Warm-up Under development TMP
Page 37 and 38:
Under development 5.8.8.3 Transitio
Page 39 and 40:
6.2.2 Generation Under development
Page 41 and 42:
Under development Table 6-1 List of
Page 43 and 44:
Under development TMPM330 (rev0.4)
Page 45 and 46:
Page 47 and 48:
6.3.6 Interrupt Service Routine Und
Page 49 and 50:
6.4.2 CG Interrupt Mode Control Reg
Page 51 and 52:
6.4.4 CG Interrupt Mode Control Reg
Page 53 and 54:
Page 55 and 56:
6.4.7 NMI Flag Register Under devel
Page 57 and 58:
7 Input/Output Ports 7.1 Port regis
Page 59 and 60:
Under development Port A input enab
Page 61 and 62:
7.1.3 Port C (PC0~PC3) Under develo
Page 63 and 64:
7.1.5 Port E (PE0~PE6) Under develo
Page 65 and 66:
7.1.6 Port F (PF0~PF7) Under develo
Page 67 and 68:
7.1.7 Port G (PG0~PG7) Under develo
Page 69 and 70:
7.1.8 Port H (PH0~PH7) Under develo
Page 71 and 72:
7.1.10 Port J (PJ0~PJ7) Under devel
Page 73 and 74:
Under development Port K input enab
Page 75 and 76:
8.2 Differences in the Specificatio
Page 77 and 78:
Configuration Under development TMP
Page 79 and 80:
Registers 8.2.1 TMRB registers Spec
Page 81 and 82:
Under development 8.2.1.1 TMRBn ena
Page 83 and 84:
Under development 8.2.1.3 TMRB cont
Page 85 and 86:
Under development 8.2.1.5 TMRB flip
Page 87 and 88:
TBnIM (0x4001_0xx8) Under developme
Page 89 and 90:
Under development 8.2.1.9 TMRB time
Page 91 and 92:
Under development 8.3 Description o
Page 93 and 94:
Under development TMPM330 (rev 0.4)
Page 95 and 96:
Page 97 and 98:
• Register setting Under developm
Page 99 and 100:
Under development 8.4 Description o
Page 101 and 102:
Under development The block diagram
Page 103 and 104:
Under development 8.6 Applications
Page 105 and 106:
Prescaler output clock TB5IN0 pin i
Page 107 and 108:
9 Serial Channel (SIO) 9.1 Features
Page 109 and 110:
• Mode 0 (I/O Interface mode) /LS
Page 111 and 112:
Under development 9.3 Operation of
Page 113 and 114:
Under development (Note 1) The pres
Page 115 and 116:
Under development (Note 1) The pres
Page 117 and 118:
• Example baud rate setting: Unde
Page 119 and 120:
fc [MHz] Under development Table 9-
Page 121 and 122:
Page 123 and 124:
Under development I/O interface mo
Page 125 and 126:
• Handshake function Data write t
Page 127 and 128:
9.3.10 Transmit FIFO Buffer Under d
Page 129 and 130:
9.3.12 Parity Control Circuit 9.3.1
Page 131 and 132:
Under development 9.3.17 Configurat
Page 133 and 134:
Under development 9.4 Register Desc
Page 135 and 136:
9.4.4 Mode control register 0 SC0MO
Page 137 and 138:
Under development : This is a statu
Page 139 and 140:
Page 141 and 142:
9.4.10 TX FIFO configuration regist
Page 143 and 144:
9.5 Operation in Each Mode 9.5.1 Mo
Page 145 and 146:
SCLK input mode Under development T
Page 147 and 148:
Receiving data SCLK output mode Rec
Page 149 and 150:
Transmit and receive (full-duplex)
Page 151 and 152:
SCLK input mode Under development T
Page 153 and 154:
9.5.2 Mode 1 (7-bit UART Mode) Unde
Page 155 and 156:
9.5.4 Mode 3 (9-bit UART) Under dev
Page 157 and 158:
10. Serial Bus Interface (SBI) Chan
Page 159 and 160:
10.2 Control Under development TMPM
Page 161 and 162:
SBIxCR0 10.4 Control Registers in t
Page 163 and 164:
Page 165 and 166:
Under development Table 10-1 Base C
Page 167 and 168:
SBIxBR0 bit Symbol I2SBI0 Under dev
Page 169 and 170:
10.5 Control in the I 2 C Bus Mode
Page 171 and 172:
Under development 10.5.6 Configurin
Page 173 and 174:
Master A Master B Under development
Page 175 and 176:
Under development 10.6 Data Transfe
Page 177 and 178:
SCL pin Write to SBIxDBR SDA pin I
Page 179 and 180:
Slave mode ( = “0”) Under devel
Page 181 and 182:
10.6.4 Generating the Stop Conditio
Page 183 and 184:
Under development 10.7 Control in t
Page 185 and 186:
SBIxDBR SBIxCR2 Under development S
Page 187 and 188:
10.7.1 Serial Clock SCK pin output
Page 189 and 190:
10.7.2 Transfer Modes Under develop
Page 191 and 192:
SCK pin SIOF SO pin bit 6 Under dev
Page 193 and 194:
SCK pin (output) SO pin SI pin IN
Page 195 and 196:
11.2 Registers 11.2.1 Control Regis
Page 197 and 198:
Under development 11.2.5 Software R
Page 199 and 200:
Under development 11.2.7 Receive Bu
Page 201 and 202:
Under development TMPM330 (rev0.4)1
Page 203 and 204:
Under development 11.2.10 Receive C
Page 205 and 206:
Under development 11.2.11 Transmit
Page 207 and 208:
Under development 11.2.13 Transmit
Page 209 and 210:
Under development 11.2.14 Receive I
Page 211 and 212:
11.3 Operations 11.3.1 Reception 11
Page 213 and 214:
(3) Cycle Error Under development C
Page 215 and 216:
(10) Waveform Error Detection Under
Page 217 and 218:
11.3.1.6 Data Sampling Point Under
Page 219 and 220:
11.3.1.8 Detecting Error Interrupt
Page 221 and 222:
Under development TMPM330 (rev0.4)1
Page 223 and 224:
11.3.2.2 Preconfiguration Under dev
Page 225 and 226:
11.3.2.3 Starting Transmission Unde
Page 227 and 228:
(2) ACK error Under development TMP
Page 229 and 230:
Under development 12 Remote control
Page 231 and 232:
Under development 12.2.2 Remote Con
Page 233 and 234:
Page 235 and 236:
(Note) Under development When you c
Page 237 and 238:
Page 239 and 240:
Under development 12.2.11 Remote Co
Page 241 and 242:
12.3.1.3 Preparation Under developm
Page 243 and 244:
(3) Settings of Data Bit Determinat
Page 245 and 246:
12.3.1.6 Reception Completion Under
Page 247 and 248:
Under development 12.3.1.8 Receivin
Page 249 and 250:
Remote control signal waveform (inp
Page 251 and 252:
Remote control signal in phase meth
Page 253 and 254:
13.1 Registers Under development Th
Page 255 and 256:
ADMOD1 Under development A/D Mode C
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
ADREG2AL ADREG2AH ADREG3BL ADREG3BH
Page 263 and 264:
ADREG6EL ADREG6EL ADREG6EL ADREG6EL
Page 265 and 266:
ADCMP0L ADCMP0H ADCMP1L ADCMP1H Und
Page 267 and 268:
13.4 Description of Operations 13.4
Page 269 and 270:
Page 271 and 272:
Under development 3. Fixed channel
Page 273 and 274:
13.4.5 High-priority Conversion Mod
Page 275 and 276:
Under development 14. Watchdog Time
Page 277 and 278:
14.3 Control Registers Under develo
Page 279 and 280:
14.4 Control Register Under develop
Page 281 and 282:
15.3 Control Register Under develop
Page 283 and 284:
MINR Under development (2) Minute c
Page 285 and 286:
DAYR DATER Under development (4) Da
Page 287 and 288:
YEARR YEARR Under development (8) Y
Page 289 and 290: 15.5 Operational description (1) Re
Page 291 and 292: 3. Disabling the clock Under develo
Page 293 and 294: (2) 1Hz clock Under development TMP
Page 295 and 296: 16.1 Addresses [1] Port [1/4] ADR
Page 297 and 298: [1] Port 3/4] ADR Register name AD
Page 299 and 300: [2] 16-bit timer [1/4] ADR Registe
Page 301 and 302: [2] 16-bit timer [3/4] ADR Registe
Page 303 and 304: Under development [3] Serial bus in
Page 305 and 306: [5] 10-bit A/D converter (A/DC) ADR
Page 307 and 308: [10] Remote control signal preproce
Page 309 and 310: Under development JEDEC compliant f
Page 311 and 312: Under development TMPM330 (rev 0.4)
Page 313 and 314: User Boot Mode Under development (1
Page 315 and 316: (Step-5) Under development TMPM330
Page 319 and 320: 17.2.3 Single Boot Mode Under devel
Page 323 and 324: (1) Configuration for Single Boot M
Page 325 and 326: (5) Restrictions on internal memori
Page 327 and 328: Under development Table 17-7 Transf
Page 329 and 330: Under development Table 17-9 Transf
Page 331 and 332: (6) Operation of Boot Program Under
Page 335 and 336: Under development returns to the st
Page 337 and 338: Under development 3) Show Product I
Page 339: Under development 4) Chip Erase com
Page 343 and 344: Point A Point B Point C Point D Und
Page 345 and 346: Start Are all bytes the same? YES A
Page 347 and 348: (7) General Boot Program Flowchart
Page 349 and 350: (2) Basic operation Under developme
Page 357 and 358: Under development Table 17-17 Secur
Page 359 and 360: Address Normal comma nds Under deve
Page 361 and 362: (8) Flowchart Address = Address + 0
Page 363 and 364: 18. ROM protection 18.1 Outline Und
Page 365 and 366: 18.3 Register block. Under developm
Page 367: 18.4 Writing and erasing 18.4.1 Pro
show all

TMPM330 - Keil

Create successful ePaper yourself

Delete template?

Save as template?