1 - Roland

More documents

Recommendations

Info

MIDI Implementation ❍Balance (Controller number 8) status 2nd byte 3rd byte BnH 08H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Balance: 00H - 7FH (0 - 127) ❍Panpot (Controller number 10) status 2nd byte 3rd byte BnH 0AH vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Panpot: 00H - 40H - 7FH (left - center - right) * Adjust the stereo location over 128 steps, where 0 is far left, 64 is center, and 127 is far right. However this is not received when the Pan parameter (PATCH/CONTROL/ RxSWITCH) is OFF. ❍Expression (Controller number 11) status 2nd byte 3rd byte BnH 0BH vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Expression: 00H - 7FH (0 - 127) * If the Volume parameter (SYSTEM/CONTROL/CONTROL SOURCE) is set to VOL&EXP, the volume of the Part corresponding to the MIDI channel of the received message will be adjusted. However this is not received if the Volume parameter (PATCH/CONTROL/RxSWITCH) is OFF. * In GM mode, the volume can always be controlled. ❍Hold 1 (Controller number 64) status 2nd byte 3rd byte BnH 40H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON * Not received when the Hold-1 RxSwitch parameter (PATCH/CONTROL/DAMPER) is OFF. ❍Portamento (Controller number 65) status 2nd byte 3rd byte BnH 41H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON * The Sw parameter (PATCH/CONTROL/PORTAMENTO) will change. ❍Sostenuto (Controller number 66) status 2nd byte 3rd byte BnH 42H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON ❍Soft (Controller number 67) status 2nd byte 3rd byte BnH 43H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON ❍Hold 2 (Controller number 69) status 2nd byte 3rd byte BnH 45H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 7FH (0 - 127) * A hold movement isn't done. ❍Sound Controller 2 (Controller number 71) status 2nd byte 3rd byte BnH 47H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 40H - 7FH (-128 - 0 - +126) * The Res parameter (PATCH/TVF/FILTER) will change relatively. ❍Sound Controller 3 (Controller number 72) status 2nd byte 3rd byte BnH 48H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 40H - 7FH (-128 - 0 - +126) * The T2–4 parameter (PATCH/TVF/TVF ENVELOPE), The T2–4 parameter (PATCH/ TVA/TVA ENVELOPE) will change relatively. ❍Sound Controller 4 (Controller number 73) status 2nd byte 3rd byte BnH 49H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 40H - 7FH (-128 - 0 - +126) * The T1 parameter (PATCH/TVF/TVF ENVELOPE), The T1 parameter (PATCH/TVA/ TVA ENVELOPE) will change relatively. ❍Sound Controller 5 (Controller number 74) status 2nd byte 3rd byte BnH 4AH vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 40H - 7FH (-64 - 0 - +63) * The Cut parameter (PATCH/TVF/FILTER) will change relatively. ❍General Purpose Controller 5 (Controller number 80) status 2nd byte 3rd byte BnH 50H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 40H - 7FH (-128 - 0 - +126) * The L1–3 parameter (PATCH/TVA/TVA ENVELOPE) of Tone 1 will change relatively. ❍General Purpose Controller 6 (Controller number 81) status 2nd byte 3rd byte BnH 51H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 40H - 7FH (-128 - 0 - +126) * The L1–3 parameter (PATCH/TVA/TVA ENVELOPE) of Tone 2 will change relatively. ❍General Purpose Controller 7 (Controller number 82) status 2nd byte 3rd byte BnH 52H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 40H - 7FH (-128 - 0 - +126) * The L1–3 parameter (PATCH/TVA/TVA ENVELOPE) of Tone 3 will change relatively. ❍General Purpose Controller 8 (Controller number 83) status 2nd byte 3rd byte BnH 53H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 40H - 7FH (-128 - 0 - +126) * The L1–3 parameter (PATCH/TVA/TVA ENVELOPE) of Tone 4 will change relatively. ❍Portamento Control (Controller number 84) status 2nd byte 3rd byte BnH 54H kkH n=MIDI channel number: 0H - FH (ch.1 - ch.16) kk=source note number: 00H - 7FH (0 - 127) * A Note On message received immediately after a Portamento control will be sounded with the pitch changing smoothly from the source note number. If a voice is already sounding at the same note number as the source note number, that voice will change pitch to the pitch of the newly received Note On, and continue sounding (i.e., will be played legato). * The speed of the pitch change caused by Portamento is determined by the Time parameter (PATCH/CONTROL/PORTAMENTO) value. 184
MIDI Implementation ❍Effect 1 (Reverb Send Level) (Controller number 91) status 2nd byte 3rd byte BnH 5BH vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Reverb Send Level: 00H - 7FH (0 - 127) ● Program Change status 2nd byte CnH ppH n=MIDI channel number: 0H - FH (ch.1 - ch.16) pp=Program number: 00H - 7FH (prog.1 - prog.128) * In Performance mode, the Reverb Send Level parameter of each Part will change. ❍Effect 3 (Chorus Send Level) (Controller number 93) status 2nd byte 3rd byte BnH 5DH vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Chorus Send Level: 00H - 7FH (0 - 127) * In Performance mode, the Chorus Send Level parameter of each Part will change. ❍RPN MSB/LSB (Controller number 100, 101) status 2nd byte 3rd byte BnH 65H mmH BnH 64H llH n=MIDI channel number: 0H - FH (ch.1 - ch.16) mm=MSB of the parameter number specified by RPN ll=LSB of the parameter number specified by RPN > Control Changes include RPN (Registered Parameter Numbers), which are extended parameters whose function is defined in the MIDI specification. When using RPNs, first the RPN (Controller numbers 100 and 101; they can be sent in any order) is transmitted to specify the parameter you wish to control. Then, Data Entry messages (Controller numbers 6 and 38) are used to set the value of the specified parameter. Once a RPN parameter has been specified, all further Data Entry messages on that channel are considered to apply to that specified parameter. In order to prevent accidents, when the desired setting has been made for the parameter, it is recommended that RPN be set to Null. * Not received when the Program Change parameter (SYSTEM/MIDI/RECEIVE MIDI) is OFF. * When received on the Control channel, the Performance will change. * Not received in Performance mode when the Rx parameter (PERFORM/MIDI/MIDI) is OFF. ● Channel Aftertouch status 2nd byte DnH vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Channel Aftertouch: 00H - 7FH (0 - 127) * Not received in Performance mode when the Rx parameter (PERFORM/MIDI/MIDI) is OFF. ● Pitch Bend Change status 2nd byte 3rd byte EnH llH mmH n=MIDI channel number: 0H - FH (ch.1 - ch.16) mm,ll=Pitch Bend value: 00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191) * Not received in Performance mode when the Rx parameter (PERFORM/MIDI/MIDI) is OFF. ■ Channel Mode Messages This device receives the following RPNs. RPN Data entry MSB LSB MSB LSB Notes 00H 00H mmH - Pitch Bend Sensitivity mm : 00H - 0CH (0 - 12 semitones) ll : ignored (processed as 00H) Up to 1 octave can be specified in semitone steps. *The Bend Range parameter (PATCH/ CONTROL/KEY MODE & BENDER) will also be changed. *Not received by the Rhythm Part (Part 10). 00H 01H mmH llH Channel Fine Tuning mm, ll : 20 00H - 40 00H - 60 00H ( -4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent ) *In Patch mode, the Master parameter (SYSTEM/TUNE/TUNE) will change. *In Performance mode, the Fine parameter (PERFORM/PART/SETTING) of each Part will change. When received on the Control channel, the Master parameter (SYSTEM/ TUNE/TUNE) will change. 00H 02H mmH - Channel Coarse Tuning mm : 10H - 40H - 70H (-48 - 0 - +48 semitones) ll : ignored (processed as 00H) *Not received in Patch mode. *In Performance mode, the Coarse parameter (PERFORM/PART/SETTING) of each Part will change. 7FH 7FH - - RPN null RPN and NRPN will be set as “unspecified.” Once this setting has been made, subsequent Data Entry messages will be ignored. (It is not necessary to transmit Data Entry for RPN Null settings. Parameter values that were previously set will not change. mm, ll: ignored ● All Sound Off (Controller number 120) status 2nd byte 3rd byte BnH 78H 00H n=MIDI channel: 0H - FH (ch.1 - ch.16) * When this message is received, all notes currently sounding on the corresponding channel will be turned off. * Not received in Performance mode when the Rx parameter (PERFORM/MIDI/MIDI) is OFF. ● Reset All Controllers (Controller number 121) status 2nd byte 3rd byte BnH 79H 00H n=MIDI channel number: 0H - FH (ch.1 - ch.16) * Not received in Performance mode when the Rx parameter (PERFORM/MIDI/MIDI) is OFF. * When this message is received, the following controllers will be set to their reset values. Controller Pitch Bend Change Polyphonic Key Pressure Channel Pressure Modulation Breath type Expression Hold 1 Sostenuto Soft Hold 2 RPN NRPN System General purpose controller 10 System General purpose controller 20 Reset value [+-]0 (center) 0 (off) 0 (off) 0 (off) 0 (minimum) 127 (maximum) However the controller will be at minimum. 0 (off) 0 (off) 0 (off) 0 (off) Unset. Previously set data will not change. Unset. Previously set data will not change. (minimum) (minimum) Appendices 185
Page 1 and 2:
OWNER’S MANUAL Thank you, and con
Page 3 and 4:
Used for instructions intended to a
Page 5 and 6:
Important Notes In addition to the
Page 7 and 8:
Contents Main Features.............
Page 9 and 10:
Contents Setting Effects for a Rhyt
Page 11 and 12:
Main Features ■ High-Performance
Page 13 and 14:
Front and Rear Panel F G [INC], [DE
Page 15 and 16:
Quick Start Quick Start 15
Page 17 and 18:
Getting Ready 1 Before installing t
Page 19 and 20:
Getting Ready 9 Press [EXP D] or [E
Page 21 and 22:
Getting Ready 1 Éteindre le XP-30
Page 23 and 24:
Getting Ready 9 Appuyer sur [EXP D]
Page 25 and 26:
Getting Ready 2 Connect supplied AC
Page 27 and 28:
Getting Ready Reset to Default Fact
Page 29 and 30:
Listening to the Demo Song ■ Prof
Page 31 and 32:
Playing the Sounds Selecting Wave E
Page 33 and 34:
Playing the Sounds 5 Turn the VALUE
Page 35 and 36:
Playing the Sounds ■ Hold Pedal I
Page 37 and 38:
Playing the Sounds 3 Play a chord.
Page 39 and 40:
Chapter 2 Chapter 1 Advanced Use Ch
Page 41 and 42:
Chapter 1. Overview of the XP-30 Pa
Page 43 and 44:
Chapter 1. Overview of the XP-30 GM
Page 45 and 46:
Chapter 1. Overview of the XP-30 Mo
Page 47 and 48:
Chapter 2. Playing Playing in Patch
Page 49 and 50:
Chapter 2. Playing The following ca
Page 51 and 52:
Chapter 2. Playing Changing Sound C
Page 53 and 54:
Chapter 2. Playing 6. Make sure tha
Page 55 and 56:
Chapter 2. Playing Playing in Rhyth
Page 57 and 58:
Chapter 2. Playing Playing in Regga
Page 59 and 60:
Chapter 2. Playing 1. Press [SYSTEM
Page 61 and 62:
Chapter 3. Creating Your Own Sounds
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Chapter 4. Memory Settings (Utility
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Chapter 5. Using the XP-30 as the G
Page 127 and 128:
Chapter 5. Using the XP-30 as the G
Page 129 and 130:
Chapter 6. Getting the Full Potenti
Page 131 and 132:
Chapter 6. Getting the Full Potenti
Page 133 and 134: Chapter 6. Getting the Full Potenti
Page 139 and 140: Appendices Appendices 139
Page 141 and 142: Troubleshooting - Does the MIDI sen
Page 143 and 144: Quick Reference of Procedures The X
Page 145 and 146: Quick Reference of Procedures Adjus
Page 147 and 148: Parameter List ■ Patch Parameters
Page 149 and 150: Parameter List PITCH Group (p. 79)
Page 151 and 152: Parameter List PART Group (p. 87) D
Page 153 and 154: Parameter List ■ GM Mode Paramete
Page 155 and 156: Parameter List 12: TREMOLO-CHORUS (
Page 157 and 158: Parameter List 29: DISTORTION→CHO
Page 159 and 160: Parameter List MIDI Group (p. 112)
Page 161 and 162: Waveform List INT-B (Internal B) No
Page 163 and 164: Waveform List ● XP-A Menu Wavefor
Page 165 and 166: Waveform List XP-C (WAVE EXPANSION
Page 167 and 168: Waveform List 156 OHH MENU 176 CLAP
Page 169 and 170: Patch List PR-B (Preset B Group) No
Page 171 and 172: Patch List XP-A (WAVE EXPANSION A:
Page 173 and 174: Patch List XP-C (WAVE EXPANSION C:
Page 175 and 176: Patch List Original B.P.M. 120 Orig
Page 177 and 178: Rhythm Set List Note No. 35 C2 36 3
Page 179 and 180: Rhythm Set List XP-A (WAVE EXPANSIO
Page 181 and 182: Performance List USER (User Group)
Page 183: MIDI Implementation Model: XP-30 (6
Page 187 and 188: MIDI Implementation ● Universal R
Page 189 and 190: MIDI Implementation ❍General Purp
Page 191 and 192: MIDI Implementation | 00 33 | 0000
Page 193 and 194: MIDI Implementation ● 1-2-2.Perfo
Page 195 and 196: MIDI Implementation |————
Page 197 and 198: MIDI Implementation *1 INT, , EXP *
Page 199 and 200: MIDI Implementation 4. Supplementar
Page 201 and 202: MIDI Implementation ● Type33: ENH
Page 203 and 204: MIDI Implementation ■ Decimal/Hex
Page 205 and 206: MIDI Implementation ■ Scale Tune
Page 207 and 208: Specifications XP-30: 64 Voice Expa
Page 209 and 210: Index Symbols [+OCT] ..............
Page 211 and 212: Index K Key assign mode ...........
Page 213 and 214: Index S Save ......................
Page 215 and 216: For EU Countries Apparatus containi
show all

1 - Roland

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?