You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Chapter 3. Creating Your Own Sounds<br />
Fbk (Delay Feedback Level)<br />
Adjust the amount of delayed sound that is returned (fed<br />
back) to the delay. Higher values result in more delay repeats.<br />
* If you have selected any one of the Reverb types (ROOM1–<br />
HALL2), this parameter has no effect.<br />
HF Damp (Reverb/Delay HF Damp)<br />
Adjust the frequency above which the reverberant sound will<br />
be cut. As the frequency is set lower, more of the high<br />
frequencies will be cut, resulting in a softer and more muted<br />
reverberance. If you do not want the high frequencies to be<br />
cut, set this parameter to BYPASS.<br />
Level (Reverb/Delay Level)<br />
Adjust the volume of the reverberant (or delayed) sound.<br />
■ Making MIDI Settings for a Part<br />
(MIDI)<br />
MIDI<br />
These parameters determine how each Part will transmit and<br />
receive MIDI messages.<br />
Channel (MIDI Channel)<br />
Set the MIDI channel of each Part.<br />
* If this is set to the same channel as the Control Channel<br />
parameter (SYSTEM/MIDI/PERFORM MIDI), attempting to<br />
use MIDI messages (Program Change and Bank Select) from an<br />
external device to select Patches will select Performances<br />
instead. If you want to select Patches, change the Control<br />
Channel to a different setting.<br />
Rx (Receive Switch)<br />
Specify whether or not you want each Part to receive MIDI<br />
messages from the external MIDI devices.<br />
Normally you will leave this ON, but you can turn it OFF<br />
when you do not want a specific Part to be playing during a<br />
song playback.<br />
* To switch between ON and OFF from the PERFORM PLAY<br />
display, hold down [SHIFT] while you press the function button<br />
for the Part you want to alter.<br />
Tx (Transmit Switch)<br />
This determines, for each Part, whether or not data generated<br />
by the controller section is sent as MIDI messages from the<br />
MIDI OUT connector when the Key Mode parameter<br />
(PERFORM/COMMON/PERFORM COMMON) is set to<br />
LAYER.<br />
Normally you will leave this ON, but you can turn it OFF when<br />
you do not want the XP-30 to control external sound sources.<br />
* When the Key Mode parameter (PERFORM/COMMON/<br />
PERFORM COMMON) is set to SINGLE, the setting for the<br />
Tx parameter is deactivated, and only the MIDI messages of the<br />
current Part are sent from the MIDI OUT connector.<br />
Local (Local Switch)<br />
Specify for each Part whether or not you want to disconnect<br />
the controller section from the internal sound source when<br />
the Key Mode parameter (PERFORM/COMMON/<br />
PERFORM COMMON) is set to LAYER..<br />
Normally you will leave this ON, but you can turn it OFF<br />
when you want to use the XP-30 only to control an external<br />
sound source.<br />
* To switch between ON and OFF from the PERFORM PLAY<br />
display, press the function button for the Part you want to alter.<br />
* When the Key Mode parameter (PERFORM/COMMON/<br />
PERFORM COMMON) is at SINGLE, the setting for the<br />
Local parameter is deactivated, and when you finger the<br />
keyboard, only the patch for the current Part sounds.<br />
RxSWITCH (Receive Switch)<br />
Specify whether each Part will receive certain MIDI messages<br />
or not.<br />
Volume (Receive Volume Switch)<br />
If you want the Part to receive Volume messages, turn this<br />
ON. If not, turn this OFF.<br />
Hold-1 (Receive Hold 1 Switch)<br />
If you want the Part to receive Hold 1 messages, turn this<br />
ON. If not, turn this OFF.<br />
Program Change<br />
(Receive Program Change Switch)<br />
If you want the Part to receive Program Change messages,<br />
turn this ON. If not, turn this OFF.<br />
* If you want a Part to receive Program Change messages, you<br />
must also turn the Program Change parameter ON (SYSTEM/<br />
MIDI/RECEIVE MIDI).<br />
TRANSMIT (Transmit Bank Select)<br />
BankSelectGroup (Transmit Bank Select Group)<br />
When you select a Performance, Bank Select and Program<br />
Change messages will be transmitted for the Patch or Rhythm<br />
Set assigned to each Part as determined by this setting.<br />
PATCH: When you select a Performance, Bank Select<br />
messages and Program Change messages for the<br />
Patch/Rhythm Set that is assigned to each Part will<br />
not be transmitted.<br />
BS1-7: When you select a Performance, Bank Select and<br />
Program Change messages will be transmitted for<br />
the Patch/Rhythm Set that is assigned to each Part.<br />
In this case, the Bank Select Number that is<br />
transmitted will be determined by the Bank Select<br />
Group (BS1–7) setting. In the BANK SEL GROUP<br />
display (SYSTEM/MIDI) you can set the Bank<br />
Select number for each Bank Select Group.<br />
86