Training, Installation & Service Manual - Livewire Connections Ltd

More documents

Recommendations

Info

Grounding Recommendations F.2 Grounding Recommendations F.2.1 Grounding the ACU The ACU should be grounded to the ship/hull. For this purpose you may use a short ADU cable and a grounding kit. Further, the ACU must be grounded at its grounding stud in order to ensure proper grounding if the short ADU cable is disconnected. For further information, see Grounding the terminal on page 2-33. If you use the Extended cable support, make the ground connections through the cable support. You may need to extend the ground plane using copper foil, see the following section. F.2.1.1 Extending the ground plane In some cases it may not be possible to access the hull and at the same time place the ACU in a suitable place. A way to insure good grounding and at the same time make it possible to ground the coax cable - is to extend the ship ground plane by means of copper foil. The maximum length of the foil is determined by the width of the foil: Copper foil 5 cm wide: Max 50 cm Copper foil 10 cm wide: Max 100 cm Copper foil 20 cm wide: Max 200 cm Note The foil must be at least 0.1 mm thick. Connect the foil to the hull by plenty of screws or hard–soldering. Run the foil past the place where the short ADU cable is to be F-2 Appendix F: Grounding and RF protection 98-133966-E2
grounded and mount a grounding kit on top of the foil. For details on the jumper cable see Jumper cable for grounding on page F-14. Jumper cable F.2.2 Cable to ADU Figure F-1: Extending the ground plane Grounding the ADU You can ground the ADU to the ship/hull via one or more of its mounting bolts. Make sure to remove painting, dirt, grease etc. at the mounting holes in order to make good electrical contact to the hull. Use serrated washers when securing the mounting bolts and seal the joint with protective coating to avoid corrosion. Grounding Recommendations FFFF Grounding and RF Antenna bottom Serrated washer (stainless steel) M12 bolt (stainless steel) Mounting base Figure F-2: Grounding the ADU Note For optimum grounding use the mounting bolt located closest to the ADU cable plate, see Figure 3-22: ADU, bolt for optimum grounding on page 3-22. 98-133966-E2 Appendix F: Grounding and RF protection F-3
Page 1:
TRAINING, INSTALLATION & SERVICE MA
Page 4 and 5:
Disclaimer Any responsibility or li
Page 6 and 7:
Compass Safe Distance: SAILOR 900 V
Page 8 and 9:
vi 98-133966-E2
Page 10 and 11:
Table of contents Chapter 3 Install
Page 12 and 13:
Table of contents 6.2 Calibration o
Page 14 and 15:
Table of contents Appendix A Append
Page 16 and 17:
Table of contents F.4 Alternative g
Page 18 and 19:
List of figures Figure 3-22: ADU, b
Page 20 and 21:
List of figures Chapter 7 Installat
Page 22 and 23:
List of figures Figure 9-68: Polari
Page 24 and 25:
List of figures Figure C-5: Satelli
Page 26 and 27:
List of tables Table 6-3: Possible
Page 28 and 29:
List of tables xxvi 98-133966-E2
Page 30 and 31:
Software version 1.3 Software versi
Page 32 and 33:
Precautions 1-4 Chapter 1: About th
Page 34 and 35:
SAILOR 900 VSAT system The followin
Page 36 and 37:
SAILOR 900 VSAT system 2.1.2 Above
Page 38 and 39:
SAILOR 900 VSAT system 9. Polarisat
Page 40 and 41:
SAILOR 900 VSAT system 2.1.3 Antenn
Page 42 and 43:
SAILOR 900 VSAT system 2.1.3.3 Serv
Page 44 and 45:
Part numbers and options 2-12 Chapt
Page 46 and 47:
Unpacking 3.1.1.3 ACU (19” rack v
Page 48 and 49:
Site preparation 3.2.2 Obstructions
Page 50 and 51:
Site preparation zones (RX and TX)
Page 52 and 53:
Site preparation 3.2.6 ADU mast des
Page 54 and 55:
Site preparation 3.2.6.2 Mast lengt
Page 56 and 57:
Site preparation Mast with 2 braces
Page 58 and 59:
Site preparation Radar Min. 15° Mi
Page 60 and 61:
Site preparation 3.2.7.4 GPS receiv
Page 62 and 63:
Installation of the ADU 3.3 Install
Page 64 and 65:
Installation of the ADU 4. Attach a
Page 66 and 67:
Installation of the ADU Otherwise,
Page 68 and 69:
Installation of the ADU Figure 3-22
Page 70 and 71:
Installation of the ACU (bulkhead)
Page 72 and 73:
Installation of the ACU (bulkhead)
Page 74 and 75:
Installation of the 19” rack vers
Page 76 and 77:
Installation of the VMU 3.6 Install
Page 78 and 79:
Installing the dual-antenna mode (o
Page 80 and 81:
Interfaces of the SAILOR 900 VSAT A
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Interfaces of the VMU 4.2.2 Connect
Page 90 and 91:
Interfaces of the VMU 4.2.5 Connect
Page 92 and 93:
Power cable selection 5.2 Power cab
Page 94 and 95:
Connecting power For other cable ty
Page 96 and 97:
Power up 5.4.0.1 Initialisation in
Page 98 and 99:
Introduction to the built-in web in
Page 100 and 101:
Calibration of the SAILOR 900 VSAT
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Configuration with the web interfac
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Keypad and menus of the ACU After 1
Page 148 and 149:
Keypad and menus of the ACU 6.4.3.1
Page 150 and 151:
Keypad and menus of the ACU SATELLI
Page 152 and 153:
SNMP support 6-56 Chapter 6: Config
Page 154 and 155:
Installation check list: Antenna St
Page 156 and 157:
Installation check list: ACU, conne
Page 158 and 159:
Installation check list: Functional
Page 160 and 161:
SAILOR 900 VSAT Viewing system para
Page 162 and 163:
Getting support: Helpdesk 9.1 Getti
Page 164 and 165:
Getting support: Helpdesk 9.1.1.4 S
Page 166 and 167:
Software update Note that the uploa
Page 168 and 169:
Status signalling with LEDs and sta
Page 170 and 171:
Status signalling with LEDs and sta
Page 172 and 173:
Removal and replacement of ADU modu
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
Updating VIM/PCM calibration data F
Page 252 and 253:
Troubleshooting 9.7.4 Troubleshooti
Page 255: Appendices
Page 258 and 259: SAILOR 900 VSAT system components A
Page 260 and 261: SAILOR 900 VSAT system components A
Page 262 and 263: Outline drawings A.2 Outline drawin
Page 264 and 265: Outline drawings A.2.3 ACU, 19 inch
Page 266 and 267: VSAT LNB Data Sheet (physical LNB)
Page 268 and 269: VSAT 8 W BUC Data Sheet (Extended)
Page 270 and 271: Modem Cable Comtech Serial & RSSI T
Page 272 and 273: Modem Cable iNIFINITI iDirect VSAT
Page 274 and 275: Open AMIP setup for iDirect INFINIT
Page 282 and 283: Non-Open-AMIP setup for iDirect iNF
Page 284 and 285: Non-Open-AMIP setup for iDirect iNF
Page 286 and 287: Comtech 570L, ROSS box & ACU C.3 Co
Page 288 and 289: STM SatLink 2900 VSAT modem To disp
Page 290 and 291: Gilat SkyEdge II VSAT modem Paramet
Page 292 and 293: Introduction D.1.1 Telnet connectio
Page 294 and 295: Supported commands D.2 Supported co
Page 296 and 297: Supported commands Command help tra
Page 298 and 299: Supported commands Command satellit
Page 300 and 301: Supported commands Command system r
Page 302 and 303: Supported commands D-12 Chapter D:
Page 304 and 305: VSAT coverage Satellite name Satell
Page 308 and 309: Grounding Recommendations It is alw
Page 310 and 311: Alternative grounding for steel hul
Page 312 and 313: Alternative grounding for aluminum
Page 314 and 315: Alternative grounding for fibre gla
Page 316 and 317: Separate ground cable F.6.2 Ground
Page 318 and 319: Jumper cable for grounding F.7 Jump
Page 320 and 321: RF interference F-16 Chapter F: Gro
Page 322 and 323: List of ADU events G.2 List of ADU
Page 324 and 325: List of ADU events Error code (ID)
Page 330 and 331: List of ACU events Error code (ID)
Page 332 and 333: List of ACU events Error code (ID)
Page 334 and 335: CE (R&TTE) H-2 Appendix H: Approval
Page 336 and 337: Glossary ETSI European Telecommunic
Page 338 and 339: Glossary RSSI Received Signal Stren
Page 340 and 341: Index browser settings for web inte
Page 342 and 343: Index F factory default calibration
Page 344 and 345: Index OpenAMIP setup, C-2 supported
Page 346: Index symbol rate DVB, azimuth cali
show all

Training, Installation & Service Manual - Livewire Connections Ltd

Create successful ePaper yourself

Delete template?

Save as template?