Tecnai on-line help manual -- Options - UT Southwestern

More documents

Recommendations

Info

<strong>Tecnai</strong> on-line help Options 130Options Software version 29.3 Magnification Calibration File Control PanelThe File tab of the Magnification Calibration Control Panelcontains the controls used for setting magnification tables fromstored calibrations.Set Mag Table from FileWhen a calibration file is selected in the Calibrations file list and DigitalMicrograph is running, it ispossible to set the magnification table from the data in the file. The software will if TIA CCD (whenpresent) should be updated as well and give a warning when TIA is not running. Next the softwarechecks that the camera currently selected in DigitalMicrograph matches that in the calibrations file. If not,the software will switch cameras. The calibration data are then loaded into the magnification tables.Calibrations file listThe result of each successful calibration is always stored to file. These files are located in the folder<strong>Tecnai</strong>\Data\Magnification Calibration and have the extension tcl. It is advised to remove old files after asuitable period. When there are too many files present (more than 100), a warning will be displayed toremove some. These files can be read in by the software to create reports. The files are sorted inchronological order (the most recent at the top). The four columns list the creation date, the name of theCCD camera, microscope lens series, and high-tension setting.9.4 Magnification Calibration Options Control PanelThe Options tab of the Magnification Calibration Control Paneldefines the automatic behavior during focusing.Focus on :For focusing there is a choice between the main screen (the main screen is lowered automatically toallow focusing) and the CCD camera (Preview mode; CCD image acquisition in the Preview mode willstart automatically). To use the latter, set the CCD Preview mode to a suitable setting (continuousacquisition, half or quarter size, exposure time ~0.25 sec).
<strong>Tecnai</strong> on-line help Options 131Options Software version 2With a GIFWith a GIF there is a choice for focusing between the TV camera (the camera is inserted automatically toallow focusing) and the CCD camera (Preview mode; CCD image acquisition in the Preview mode willstart automatically). To use the latter, set the CCD Preview mode to a suitable setting (continuousacquisition, half or quarter size, exposure time ~0.25 sec).
Page 5:
Tecnai on-line hel
Page 9 and 10:
Tecnai on-line hel
Page 11 and 12:
Tecnai on-line hel
Page 13 and 14:
Tecnai on-line hel
Page 15 and 16:
Tecnai on-line hel
Page 17 and 18:
Tecnai on-line hel
Page 19 and 20:
Tecnai on-line hel
Page 21 and 22:
Tecnai on-line hel
Page 23 and 24:
Tecnai on-line hel
Page 25 and 26:
Tecnai on-line hel
Page 27 and 28:
Tecnai on-line hel
Page 29 and 30:
Tecnai on-line hel
Page 31 and 32:
Tecnai on-line hel
Page 33 and 34:
Tecnai on-line hel
Page 35 and 36:
Tecnai on-line hel
Page 37 and 38:
Tecnai on-line hel
Page 39 and 40:
Tecnai on-line hel
Page 41 and 42:
Tecnai on-line hel
Page 43 and 44:
Tecnai on-line hel
Page 45 and 46:
Tecnai on-line hel
Page 47 and 48:
Tecnai on-line hel
Page 49 and 50:
Tecnai on-line hel
Page 51 and 52:
Tecnai on-line hel
Page 53 and 54:
Tecnai on-line hel
Page 55 and 56:
Tecnai on-line hel
Page 57 and 58:
Tecnai on-line hel
Page 59 and 60:
Tecnai on-line hel
Page 61 and 62:
Tecnai on-line hel
Page 63 and 64:
Tecnai on-line hel
Page 65 and 66:
Tecnai on-line hel
Page 67 and 68:
Tecnai on-line hel
Page 69 and 70:
Tecnai on-line hel
Page 71 and 72:
Tecnai on-line hel
Page 73 and 74:
Tecnai on-line hel
Page 75 and 76:
Tecnai on-line hel
Page 77 and 78:
Tecnai on-line hel
Page 79 and 80: Tecnai on-line hel
Page 129: Tecnai on-line hel
Page 169: Tecnai on-line hel
show all

Tecnai on-line help manual -- Options - UT Southwestern

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?