Strato X User Manual - Image Works

More documents

Recommendations

Info

USER'S MANUAL General instructions for use 6.8.4 Making an exposure WARNING: During the emission of X-rays, the protection procedures for the operator and personnel in the area must be in compliance with the regulations in force in the country where the machine is used. In all cases, it is recommended that during the emission of X-rays, only the patient and operator be present in the room. If the operator is not protected by suitable screens, he must stand at least 1.5 meters away from the emission of the X-rays (see Figure 1 and Figure 2). 1. Verify once again that the exposure data are correct (see paragraph 6.8.2). Advise the patient to remain still and to keep his mouth closed with the teeth touching throughout the duration of the exposure. Press key "23" . The collimator corresponding to the selected cassette will be placed in position. Furthermore, if the type of exposure requires it, the soft tissues filter will be positioned according to the value set by the operator. Check that the light unit ready for X-ray is ON. NOTE: To return to the previous step, press button "10" . 2. Press the X-ray button "30" for the entire duration of the exposure, ensuring that the X-ray light 2 is also lit (if the unit is in view) and that the X-ray signal acoustic sounds. The following message will be displayed first: S T A R T E X A M P R E - H E A T I N G and then (after 2 seconds), the following message will be displayed: > X - R A Y < x x k V x x m A x . x x s x = the value defined by the settings (Rev. 1) 113 STRATO X (120V)
USER'S MANUAL General instructions for use NOTE: If there is no cassette, the following message will be displayed: C E P H I N S E R T F I L M . NOTE: If, during the preparation of the first cephalometric examination the system detects a cassette which has not been replaced, the following message will be displayed: C E P H R E M O V E F I L M The examination will not be continued until a new cassette has been inserted. NOTE: X-rays are emitted with a delay of two seconds from pressing the X-ray button to allow the heating of the filament and the control of all set parameters. Since the X-ray button is a "dead man" control, it must be kept pressed until the end of the exposure. 3. Once the exposure is completed, the following message will be displayed: C E P H R E M O V E F I L M 4. Remove the cassette. LED "23" lights up and the set cassette, STF, kV, mA and seconds values relative to the exposure made will be displayed. NOTE: If you try to perform a new exam before the cooling period has elapse (4 minutes), the following message will be displayed indicating the time to wait before performing a new examination: T U B E C O O L I N G P L E A S E W A I T x x x s This time enables the X-ray tube's anode to cool down. STRATO X (120V) 114 (Rev. 1)
Page 1 and 2:
STRATO X 0434 (120V version) User's
Page 3 and 4:
USER'S MANUAL Revision history THIS
Page 5 and 6:
USER'S MANUAL Contents 6.5 TMJ exam
Page 7 and 8:
USER'S MANUAL Contents THIS PAGE IS
Page 9 and 10:
USER'S MANUAL Safety information 2.
Page 11 and 12:
USER'S MANUAL Safety information Th
Page 13 and 14:
USER'S MANUAL Safety information 2.
Page 15 and 16:
USER'S MANUAL Cleaning and disinfec
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
USER'S MANUAL Technical specificati
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
USER'S MANUAL General instructions
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70: USER'S MANUAL General instructions
Page 119: USER'S MANUAL General instructions
Page 149 and 150: USER'S MANUAL Maintenance MAINTENAN
show all

Strato X User Manual - Image Works

Create successful ePaper yourself

Delete template?

Save as template?