SINUMERIK 840D/810D ShopMill

More documents

Recommendations

Info

9ToolManagement 9.2 Start-up of the tool management in the NC Machine data for activating the tool management Default setting 9-106 12.01 In addition, the following machine data must be set for activating the tool management: MD 20310 Channel-specific activation of the tool management MD 20320 Activation of the life time monitoring for the specified spindle MD 22550 New tool offset for M function MD 22560 M function for tool change MD 22562 Error reaction with programmed tool change Note Bits 0--3 of MD 20310 $MC_TOOL_MANAGEMENT_MASK and MD 18080 $MN_MM_TOOL_MANAGEMENT_MASK must always be set identically. The NC machine data for tool management are contained in MD record CMM.8X0 (for default setting see overview in Section 6.1 “NC machine data for ShopMill”). A detailed description of the NC machine data for tool management is given in the next Subsection 9.2.3 “Description of the NC machine data for the tool management”. E Siemens AG, 2001. All rights reserved SINUMERIK 840D/810D Description of Functions ShopMill (FBSP) - 12.01 Edition
12.01 E Siemens AG, 2001. All rights reserved SINUMERIK 840D/810D Description of Functions ShopMill (FBSP) - 12.01 Edition 9ToolManagement 9.2 Start-up of the tool management in the NC 9.2.3 Description of the NC machine data for tool management 18080 MM_TOOL_MANAGEMENT_MASK MD number Activation of memory for tool management Default setting: 0x0 Min. input limit: 0 Max. input limit: 0xFFFF Changes valid from: POWER ON Protection level: 1/4 Unit: HEX Data type: DWORD Valid as of software version: 4.3 Meaning: Activation of the tool management memory with “0” means: The set tool management data do not use memory space. Bit0=1: Memory is provided for tool management-specific data Bit1=1: Memory is provided for monitoring data Bit2=1: Memory is provided for user data (CC data) Bit3=1: Memory is provided for considering the adjacent location Bit4=1: D-RAM is provided for “Complex searching for tools in magazines”. Bit5=1: Wear monitor active (SW5 and later, 840D) Bit6=1: Wear grouping available (SW5 and later, 840D) The coded type of memory reservation enables economic use of the memory management for the functionality provided. Example: Default memory reservation for TM: MD = 3 (Bit0 + 1=1) MD = 1 means TM without TM monitoring function data 18082 MM_NUM_TOOL MD number Number of tools the NCK can manage Default setting: 30 Min. input limit: 0 Max. input limit: 600 Changes valid from: POWER ON Protection level: 2/4 Unit: - - Data type: DWORD Valid as of software version: 2 Meaning: The number of tools which the NCK can manage is entered here. Battery-backed memory is reserved for the number of tools. Further references: Description of Functions: Memory Configuration (S7), Tool Offset (W1) 18084 MM_NUM_MAGAZINE MD number Number of magazines the NCK can manage Default setting: 3 Min. input limit: 0 Max. input limit: 32 Changes valid from: POWER ON Protection level: 2/4 Unit: - - Data type: DWORD Valid as of software version: 2 Meaning: Number of magazines the NCK can manage (active and background magazines). This MD can be used to reserve battery-backed memory for the magazines. Important: One load magazine and a buffer magazine is set up in the tool management for each TOA unit. These magazines must be taken into account. Value = 0: The tool management cannot be active because no data could be created. Further references: Description of Functions: Memory Configuration (S7) 9-107
Page 1:
SINUMERIK 840D/810D Description of
Page 4 and 5:
SINUMERIK R Documentation Printing
Page 6 and 7:
Preface Searching aids Notes Warnin
Page 8 and 9:
Preface viii Notes 12.01 E Siemens
Page 10 and 11:
Contents x 12.01 7 Reserved Functio
Page 12 and 13:
Contents xii Notes 12.01 Siemens A
Page 14 and 15:
1Hardware 1.1 Hardware assembly Tab
Page 16 and 17:
1Hardware 1.2 Examples for assignin
Page 18 and 19:
2Installation and Start-Up 2.1 Prec
Page 20 and 21:
2Installation and Start-Up 2.2 Init
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
2Installation and Start-Up 2.3 Seri
Page 34 and 35:
3 Supplementary Conditions 3-34 Not
Page 36 and 37:
4PLCProgram 4.2 Example for OB1 and
Page 38 and 39:
4PLCProgram 4.2 Example for OB1 and
Page 40 and 41:
4PLCProgram 4.3 Overview of blocks
Page 42 and 43:
4PLCProgram 4.4 Description of bloc
Page 44 and 45:
4PLCProgram 4.4 Description of bloc
Page 46 and 47:
4PLCProgram 4.5 Standard interface
Page 48 and 49:
5SignalDescription 5.1 Overview of
Page 50 and 51:
5SignalDescription 5.1 Overview of
Page 52 and 53:
5SignalDescription 5.2 Description
Page 54 and 55:
5SignalDescription 5.2 Description
Page 56 and 57: 5SignalDescription 5.2 Description
Page 70 and 71: 6Machine Data 6.1 NC machine data f
Page 72 and 73: 6Machine Data 6.2 Display machine d
Page 88 and 89: 7 Reserved Functions 7-88 Notes 12.
Page 90 and 91: 8 Tools 8.1 Tool-changing cycle ada
Page 92 and 93: 8 Tools 8.2 Manual tools 8.2 Manual
Page 94 and 95: 8 Tools 8.4 Activate tool-specific
Page 96 and 97: 8 Tools 8.5 Modify texts for tool-s
Page 102 and 103: 9ToolManagement 9.1 Overview of fun
Page 104 and 105: 9ToolManagement 9.2 Start-up of the
Page 120 and 121: 9ToolManagement 9.3 Tool management
Page 130 and 131: 9ToolManagement 9.4 Examples 9.4 Ex
Page 132 and 133: 9ToolManagement 9.4 Examples Create
Page 134 and 135: 9ToolManagement 9.4 Examples 9-134
Page 136 and 137: 9ToolManagement 9.5 Configuring the
Page 144 and 145: 10 Measuring Cycles 10.2 Probe conn
Page 146 and 147: 10 Measuring Cycles 10.3 Functional
Page 148 and 149: 10 Measuring Cycles 10.4 Start-up s
Page 150 and 151: 10 Measuring Cycles 10.4 Start-up s
Page 152 and 153: 10 Measuring Cycles 10.5 Machine da
Page 154 and 155: 10 Measuring Cycles 10.5 Machine da
Page 156 and 157:
10 Measuring Cycles 10.5 Machine da
Page 158 and 159:
11 Network Link 11.2 Linking Window
Page 160 and 161:
11 Network Link 11.2 Linking Window
Page 162 and 163:
12 Access Protection via Password a
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
13 Miscellaneous 13.1 Configuring t
Page 170 and 171:
13 Miscellaneous 13.2 Configuring t
Page 172 and 173:
13 Miscellaneous 13.3 Cylinder surf
Page 174 and 175:
13 Miscellaneous 13.3 Cylinder surf
Page 176 and 177:
13 Miscellaneous 13.4 Swivel heads
Page 178 and 179:
13 Miscellaneous 13.5 Multiple clam
Page 180 and 181:
13 Miscellaneous 13.7 Spindle contr
Page 182 and 183:
13 Miscellaneous 13.9 ShopMill Open
Page 184 and 185:
13 Miscellaneous 13.11 User status
Page 186 and 187:
13 Miscellaneous 13.12 OP hotkeys,
Page 188 and 189:
A Abbreviations MCP MD MMC MPF MPI
Page 190 and 191:
A Abbreviations A-190 Notes 12.01
Page 192 and 193:
B References User Documentation /AU
Page 194 and 195:
B References /PGT/ /PGZ/ /PI / /SYI
Page 196 and 197:
B References /FB3/ /FBA/ B-196 A4 D
Page 198 and 199:
B References /FBO/ /FBP/ /FBR/ /FBS
Page 200 and 201:
B References /PJU/ /POS1/ /POS2/ /P
Page 202 and 203:
B References B-202 Notes 12.01 Sie
Page 204 and 205:
C Index N NC machine data exact val
Page 206:
SINUMERIK 840D/810D Documentation o
show all

SINUMERIK 840D/810D ShopMill

Create successful ePaper yourself

Delete template?

Save as template?