SINUMERIK 840D/810D ShopMill

More documents

Recommendations

Info

6Machine Data 6.2 Display machine data for ShopMill 9661 $MM_CMM_ENABLE_CUSTOMER_M_CODES MD number Number of input fields for customized M commands Default setting: 0 Min. input limit: 0 Max. input limit: 4 Changes valid from: POWER ON Protection level: 3/4 Unit: - Data type: BYTE Valid as of software version: 840D SW 4.3, 810D SW 2.3 Meaning: This MD activates the number of input fields for customized M commands: 6-80 0 = No display fields for customized M commands 1 = 1 field for one customized M command is displayed 2 = 2 fields for 2 customized M commands are displayed 3 = 3 fields for 3 customized M commands are displayed 4 = 4 fields for 4 customized M commands are displayed 9662 $MM_CMM_COUNT_GEAR_STEPS MD number Number of gear steps Default setting: 1 Min. input limit: 0 Max. input limit: 5 Changes valid from: IMMEDIATE Protection level: 3/4 Unit: - Data type: BYTE Valid as of software version: 840D SW 4.3, 810D SW 2.3 Meaning: This MD is for setting the number of gear steps (0 to 5) for the spindle. The possibility of input in the user interface is thus restricted. 9663 $MM_CMM_TOOL_DISPLAY_IN_DIAM MD number Display radius/diameter for tool Default setting: 1 Min. input limit: 0 Max. input limit: 1 Changes valid from: POWER ON Protection level: 3/4 Unit: - Data type: BYTE Valid as of software version: 840D SW 4.3, 810D SW 2.3 Meaning: This MD defines how the tool is displayed or is to be input: 0 = Radius 1 = Diameter 9664 $MM_CMM_MAX_INP_FEED_P_MIN MD number Max. feed in mm/min Default setting: 10000.0 Min. input limit: 0.0 Max. input limit: 100000.0 Changes valid from: IMMEDIATE Protection level: 3/4 Unit: mm/min Data type: DOUBLE Valid as of software version: 840D SW 4.3, 810D SW 2.3 Meaning: This MD is for entering the upper feedrate input limit for mm/min. 9665 $MM_CMM_MAX_INP_FEED_P_ROT MD number Max. feed in mm/rev Default setting: 1.0 Min. input limit: 0.0 Max. input limit: 10.0 Changes valid from: IMMEDIATE Protection level: 3/4 Unit: mm/rev Data type: DOUBLE Valid as of software version: 840D SW 4.3, 810D SW 2.3 Meaning: This MD is for entering the upper feedrate input limit for mm/rev. 12.01 E Siemens AG, 2001. All rights reserved SINUMERIK 840D/810D Description of Functions ShopMill (FBSP) - 12.01 Edition
12.01 E Siemens AG, 2001. All rights reserved SINUMERIK 840D/810D Description of Functions ShopMill (FBSP) - 12.01 Edition 6Machine Data 6.2 Display machine data for ShopMill 9666 $MM_CMM_MAX_INP_FEED_P_TOOTH MD number Max. feed in mm/tooth Default setting: 1.0 Min. input limit: 0.0 Max. input limit: 5.0 Changes valid from: IMMEDIATE Protection level: 3/4 Unit: mm/tooth Data type: DOUBLE Valid as of software version: 840D SW 4.3, 810D SW 2.3 Meaning: This MD is for entering the upper feedrate input limit for mm/tooth. 9667 $MM_CMM_FOLLOW_ON_TOOL_ACTIVE MD number Tool preselection active Default setting: 1 Min. input limit: 0 Max. input limit: 1 Changes valid from: IMMEDIATE Protection level: 3/4 Unit: - Data type: BYTE Valid as of software version: 840D SW 4.3, 810D SW 2.3 Meaning: This MD defines whether a tool preselection is active in a magazine (e.g. chain magazine), i.e. the following tool is already brought to the load station for a pending tool change. 0 = Tool preselection is not active 1 = Tool preselection is active 9668 $MM_CMM_M_CODE_COOLANT_I_AND_II MD number M code coolants I and II ( -1 = no M code) Default setting: -1 Min. input limit: -1 Max. input limit: 32767 Changes valid from: IMMEDIATE Protection level: 3/4 Unit: - Data type: WORD Valid as of software version: 840D SW 4.4, 810D SW 2.4 Meaning: This machine data enables you to specify the M code if both coolants I and II are activated simultaneously in the tool list. Value: -1 = No M code xy = Mxy for coolant I and II on (xy = value of MD 9668) 9669 $MM_CMM_FACE_MILL_EFF_TOOL_DIAM MD number Effective mill diameter for face milling Default setting: 85.0 Min. input limit: 50.0 Max. input limit: 100.0 Changes valid from: IMMEDIATE Protection level: 3/4 Unit: % Data type: DOUBLE Valid as of software version: 840D SW 4.4, 810D SW 2.4 Meaning: This MD specifies the effective mill diameter for face milling. The ratio d/D > MD 9669 (where d = cut diameter, D = largest mill diameter) defines how far the mill goes beyond the workpiece during face milling. 9670 $MM_CMM_START_RAD_CONTOUR_POCKE MD number Radius of approach circle for finishing cut on contour pockets plus half the final machining allowance ( -1 = safety clearance) Default setting: -1 Min. input limit: -1 Max. input limit: 100.0 Changes valid from: IMMEDIATE Protection level: 3/4 Unit: mm Data type: DOUBLE Valid as of software version: 840D SW 4.4, 810D SW 2.4 Meaning: This MD affects the radius of the approach circle when finishing contour pockets. -1 = The radius is selected such that the safety clearance for final machining is observed at the start point. >0 = The radius is selected such that the value of this MD for final machining allowance is observed at the start point. 6-81
Page 1:
SINUMERIK 840D/810D Description of
Page 4 and 5:
SINUMERIK R Documentation Printing
Page 6 and 7:
Preface Searching aids Notes Warnin
Page 8 and 9:
Preface viii Notes 12.01 E Siemens
Page 10 and 11:
Contents x 12.01 7 Reserved Functio
Page 12 and 13:
Contents xii Notes 12.01 Siemens A
Page 14 and 15:
1Hardware 1.1 Hardware assembly Tab
Page 16 and 17:
1Hardware 1.2 Examples for assignin
Page 18 and 19:
2Installation and Start-Up 2.1 Prec
Page 20 and 21:
2Installation and Start-Up 2.2 Init
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31: 2Installation and Start-Up 2.2 Init
Page 32 and 33: 2Installation and Start-Up 2.3 Seri
Page 34 and 35: 3 Supplementary Conditions 3-34 Not
Page 36 and 37: 4PLCProgram 4.2 Example for OB1 and
Page 38 and 39: 4PLCProgram 4.2 Example for OB1 and
Page 40 and 41: 4PLCProgram 4.3 Overview of blocks
Page 42 and 43: 4PLCProgram 4.4 Description of bloc
Page 44 and 45: 4PLCProgram 4.4 Description of bloc
Page 46 and 47: 4PLCProgram 4.5 Standard interface
Page 48 and 49: 5SignalDescription 5.1 Overview of
Page 50 and 51: 5SignalDescription 5.1 Overview of
Page 52 and 53: 5SignalDescription 5.2 Description
Page 70 and 71: 6Machine Data 6.1 NC machine data f
Page 72 and 73: 6Machine Data 6.2 Display machine d
Page 88 and 89: 7 Reserved Functions 7-88 Notes 12.
Page 90 and 91: 8 Tools 8.1 Tool-changing cycle ada
Page 92 and 93: 8 Tools 8.2 Manual tools 8.2 Manual
Page 94 and 95: 8 Tools 8.4 Activate tool-specific
Page 96 and 97: 8 Tools 8.5 Modify texts for tool-s
Page 102 and 103: 9ToolManagement 9.1 Overview of fun
Page 104 and 105: 9ToolManagement 9.2 Start-up of the
Page 120 and 121: 9ToolManagement 9.3 Tool management
Page 130 and 131:
9ToolManagement 9.4 Examples 9.4 Ex
Page 132 and 133:
9ToolManagement 9.4 Examples Create
Page 134 and 135:
9ToolManagement 9.4 Examples 9-134
Page 136 and 137:
9ToolManagement 9.5 Configuring the
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
10 Measuring Cycles 10.2 Probe conn
Page 146 and 147:
10 Measuring Cycles 10.3 Functional
Page 148 and 149:
10 Measuring Cycles 10.4 Start-up s
Page 150 and 151:
10 Measuring Cycles 10.4 Start-up s
Page 152 and 153:
10 Measuring Cycles 10.5 Machine da
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
11 Network Link 11.2 Linking Window
Page 160 and 161:
11 Network Link 11.2 Linking Window
Page 162 and 163:
12 Access Protection via Password a
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
13 Miscellaneous 13.1 Configuring t
Page 170 and 171:
13 Miscellaneous 13.2 Configuring t
Page 172 and 173:
13 Miscellaneous 13.3 Cylinder surf
Page 174 and 175:
13 Miscellaneous 13.3 Cylinder surf
Page 176 and 177:
13 Miscellaneous 13.4 Swivel heads
Page 178 and 179:
13 Miscellaneous 13.5 Multiple clam
Page 180 and 181:
13 Miscellaneous 13.7 Spindle contr
Page 182 and 183:
13 Miscellaneous 13.9 ShopMill Open
Page 184 and 185:
13 Miscellaneous 13.11 User status
Page 186 and 187:
13 Miscellaneous 13.12 OP hotkeys,
Page 188 and 189:
A Abbreviations MCP MD MMC MPF MPI
Page 190 and 191:
A Abbreviations A-190 Notes 12.01
Page 192 and 193:
B References User Documentation /AU
Page 194 and 195:
B References /PGT/ /PGZ/ /PI / /SYI
Page 196 and 197:
B References /FB3/ /FBA/ B-196 A4 D
Page 198 and 199:
B References /FBO/ /FBP/ /FBR/ /FBS
Page 200 and 201:
B References /PJU/ /POS1/ /POS2/ /P
Page 202 and 203:
B References B-202 Notes 12.01 Sie
Page 204 and 205:
C Index N NC machine data exact val
Page 206:
SINUMERIK 840D/810D Documentation o
show all

SINUMERIK 840D/810D ShopMill

Create successful ePaper yourself

Delete template?

Save as template?