SINUMERIK 840D/810D ShopMill

More documents

Recommendations

Info

10 Measuring Cycles 10.2 Probe connection 10.2 Probe connection Probe connection 10-144 12.01 A maximum of two sensors can be connected to the SINUMERIK 810D via the X121 I/O interface, which is located on the front panel of the CCU module. CCU1 X121 Fig. 10-1 Probe connection to X121 on CCU module Cable distributor Probe E Siemens AG, 2001. All rights reserved SINUMERIK 840D/810D Description of Functions ShopMill (FBSP) - 12.01 Edition
12.01 I/O interface (X121) The probe is connected via a 37-pin D-Sub pin connector (X121). The 24 V load power supply is also connected on this connector. E Siemens AG, 2001. All rights reserved SINUMERIK 840D/810D Description of Functions ShopMill (FBSP) - 12.01 Edition 10 Measuring Cycles 10.2 Probe connection Table 10-1 Extract from PIN assignment table for X121 front connectors PIN Designation External power supply 1 M24EXT External ground 2 M24EXT External ground ... ... ... Connection probe 1 9 MEPUS 0 Measuring pulse signal input 10 MEPUC 0 Measuring pulse common input ... ... ... External power supply 20 P24EXT Current 24 V external 21 P24EXT Current 24 V external ... ... ... Connection probe 2 28 MEPUS 1 Measuring pulse signal input 29 MEPUC 1 Measuring pulse common input ... ... ... 10-145
Page 1:
SINUMERIK 840D/810D Description of
Page 4 and 5:
SINUMERIK R Documentation Printing
Page 6 and 7:
Preface Searching aids Notes Warnin
Page 8 and 9:
Preface viii Notes 12.01 E Siemens
Page 10 and 11:
Contents x 12.01 7 Reserved Functio
Page 12 and 13:
Contents xii Notes 12.01 Siemens A
Page 14 and 15:
1Hardware 1.1 Hardware assembly Tab
Page 16 and 17:
1Hardware 1.2 Examples for assignin
Page 18 and 19:
2Installation and Start-Up 2.1 Prec
Page 20 and 21:
2Installation and Start-Up 2.2 Init
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
2Installation and Start-Up 2.3 Seri
Page 34 and 35:
3 Supplementary Conditions 3-34 Not
Page 36 and 37:
4PLCProgram 4.2 Example for OB1 and
Page 38 and 39:
4PLCProgram 4.2 Example for OB1 and
Page 40 and 41:
4PLCProgram 4.3 Overview of blocks
Page 42 and 43:
4PLCProgram 4.4 Description of bloc
Page 44 and 45:
4PLCProgram 4.4 Description of bloc
Page 46 and 47:
4PLCProgram 4.5 Standard interface
Page 48 and 49:
5SignalDescription 5.1 Overview of
Page 50 and 51:
5SignalDescription 5.1 Overview of
Page 52 and 53:
5SignalDescription 5.2 Description
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
6Machine Data 6.1 NC machine data f
Page 72 and 73:
6Machine Data 6.2 Display machine d
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
7 Reserved Functions 7-88 Notes 12.
Page 90 and 91:
8 Tools 8.1 Tool-changing cycle ada
Page 92 and 93:
8 Tools 8.2 Manual tools 8.2 Manual
Page 94 and 95: 8 Tools 8.4 Activate tool-specific
Page 96 and 97: 8 Tools 8.5 Modify texts for tool-s
Page 102 and 103: 9ToolManagement 9.1 Overview of fun
Page 104 and 105: 9ToolManagement 9.2 Start-up of the
Page 120 and 121: 9ToolManagement 9.3 Tool management
Page 130 and 131: 9ToolManagement 9.4 Examples 9.4 Ex
Page 132 and 133: 9ToolManagement 9.4 Examples Create
Page 134 and 135: 9ToolManagement 9.4 Examples 9-134
Page 136 and 137: 9ToolManagement 9.5 Configuring the
Page 146 and 147: 10 Measuring Cycles 10.3 Functional
Page 148 and 149: 10 Measuring Cycles 10.4 Start-up s
Page 150 and 151: 10 Measuring Cycles 10.4 Start-up s
Page 152 and 153: 10 Measuring Cycles 10.5 Machine da
Page 158 and 159: 11 Network Link 11.2 Linking Window
Page 160 and 161: 11 Network Link 11.2 Linking Window
Page 162 and 163: 12 Access Protection via Password a
Page 168 and 169: 13 Miscellaneous 13.1 Configuring t
Page 170 and 171: 13 Miscellaneous 13.2 Configuring t
Page 172 and 173: 13 Miscellaneous 13.3 Cylinder surf
Page 174 and 175: 13 Miscellaneous 13.3 Cylinder surf
Page 176 and 177: 13 Miscellaneous 13.4 Swivel heads
Page 178 and 179: 13 Miscellaneous 13.5 Multiple clam
Page 180 and 181: 13 Miscellaneous 13.7 Spindle contr
Page 182 and 183: 13 Miscellaneous 13.9 ShopMill Open
Page 184 and 185: 13 Miscellaneous 13.11 User status
Page 186 and 187: 13 Miscellaneous 13.12 OP hotkeys,
Page 188 and 189: A Abbreviations MCP MD MMC MPF MPI
Page 190 and 191: A Abbreviations A-190 Notes 12.01
Page 192 and 193: B References User Documentation /AU
Page 194 and 195:
B References /PGT/ /PGZ/ /PI / /SYI
Page 196 and 197:
B References /FB3/ /FBA/ B-196 A4 D
Page 198 and 199:
B References /FBO/ /FBP/ /FBR/ /FBS
Page 200 and 201:
B References /PJU/ /POS1/ /POS2/ /P
Page 202 and 203:
B References B-202 Notes 12.01 Sie
Page 204 and 205:
C Index N NC machine data exact val
Page 206:
SINUMERIK 840D/810D Documentation o
show all

SINUMERIK 840D/810D ShopMill

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?