SINUMERIK 840D/810D ShopMill

More documents

Recommendations

Info

8 Tools 8.4 Activate tool-specific M functions 1...4 8.4 Activate tool-specific M functions 1...4 Example 8-94 12.01 The tool-specific M functions 1...4 are intended for further machine functions, which can be activated for a tool. For example, third coolant, speed monitoring, tool break, etc. Fig. 8-3 Tool list: Tool-specific functions 1...4 Cursor texts: “Tool-spec. fct. 1...4” The fields in the tool list can be grayed out with the display MD 9661, CMM_ENABLE_CUSTOMER_M_CODES = 0. The tool-specific M functions 1...4 are output by the ShopMill tool change cycle after M6 for a PLC cycle in DB82. Tool-specific M function 1 ... 4 in DB82: DB82 DBX42.0 CMM_OUT.tool_m_function.function_1_on DB82 DBX42.1 CMM_OUT.tool_m_function.function_2_on DB82 DBX42.2 CMM_OUT.tool_m_function.function_3_on DB82 DBX42.3 CMM_OUT.tool_m_function.function_4_on DB82 DBX42.4 CMM_OUT.tool_m_function.function_1_active DB82 DBX42.5 CMM_OUT.tool_m_function.function_2_active DB82 DBX42.6 CMM_OUT.tool_m_function.function_3_active DB82 DBX42.7 CMM_OUT.tool_m_function.function_4_active Bits DB82.DBX42.4...7 indicates whether the function displayed in bits DB82.DBX42.0...3 is valid. The signal is low active. The following functions are programmed: Tool-specific M_function 1: On Tool-specific M_function 2: No change Tool-specific M_function 3: Off Tool-specific M_function 4: No change M command M90=161 is generated. The following bits are set in DB82.DBB42: Table 8-1 DB82.DBB42 Bit Status Function 0 1 Activate tool-specific M function 1 1 0 No change in tool-specific M function 2 2 0 Deactivate tool-specific M function 3 3 0 No change in tool-specific M function 4 4 0 Accept function from bit0 5 1 Do not accept function from bit1 6 0 Accept function from bit2 7 1 Do not accept function from bit3 E Siemens AG, 2001. All rights reserved SINUMERIK 840D/810D Description of Functions ShopMill (FBSP) - 12.01 Edition
12.01 Special features in “MANUAL” mode Modifying the cursor texts E Siemens AG, 2001. All rights reserved SINUMERIK 840D/810D Description of Functions ShopMill (FBSP) - 12.01 Edition 8 Tools 8.4 Activate tool-specific M functions 1...4 In “MANUAL” mode, no tool-specific M functions are output to the PLC. On tool change in the “MANUAL” mode, these functions can be initiated by the operator using the keys on the machine control panel (implementation via PLC user program). The cursor texts (“Tool-specific function 1, ...”) are stored in the CUST.TXT file and can be modified (see Section 8.5 “Modifying texts for tool-specific functions”). Note Tool-specific M functions are output from the HMI to the ShopMill PLC using M functions with extended address (see Chapter 7 “Reservations”). 8-95
Page 1:
SINUMERIK 840D/810D Description of
Page 4 and 5:
SINUMERIK R Documentation Printing
Page 6 and 7:
Preface Searching aids Notes Warnin
Page 8 and 9:
Preface viii Notes 12.01 E Siemens
Page 10 and 11:
Contents x 12.01 7 Reserved Functio
Page 12 and 13:
Contents xii Notes 12.01 Siemens A
Page 14 and 15:
1Hardware 1.1 Hardware assembly Tab
Page 16 and 17:
1Hardware 1.2 Examples for assignin
Page 18 and 19:
2Installation and Start-Up 2.1 Prec
Page 20 and 21:
2Installation and Start-Up 2.2 Init
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
2Installation and Start-Up 2.3 Seri
Page 34 and 35:
3 Supplementary Conditions 3-34 Not
Page 36 and 37:
4PLCProgram 4.2 Example for OB1 and
Page 38 and 39:
4PLCProgram 4.2 Example for OB1 and
Page 40 and 41:
4PLCProgram 4.3 Overview of blocks
Page 42 and 43:
4PLCProgram 4.4 Description of bloc
Page 44 and 45: 4PLCProgram 4.4 Description of bloc
Page 46 and 47: 4PLCProgram 4.5 Standard interface
Page 48 and 49: 5SignalDescription 5.1 Overview of
Page 50 and 51: 5SignalDescription 5.1 Overview of
Page 52 and 53: 5SignalDescription 5.2 Description
Page 70 and 71: 6Machine Data 6.1 NC machine data f
Page 72 and 73: 6Machine Data 6.2 Display machine d
Page 88 and 89: 7 Reserved Functions 7-88 Notes 12.
Page 90 and 91: 8 Tools 8.1 Tool-changing cycle ada
Page 92 and 93: 8 Tools 8.2 Manual tools 8.2 Manual
Page 96 and 97: 8 Tools 8.5 Modify texts for tool-s
Page 102 and 103: 9ToolManagement 9.1 Overview of fun
Page 104 and 105: 9ToolManagement 9.2 Start-up of the
Page 120 and 121: 9ToolManagement 9.3 Tool management
Page 130 and 131: 9ToolManagement 9.4 Examples 9.4 Ex
Page 132 and 133: 9ToolManagement 9.4 Examples Create
Page 134 and 135: 9ToolManagement 9.4 Examples 9-134
Page 136 and 137: 9ToolManagement 9.5 Configuring the
Page 144 and 145:
10 Measuring Cycles 10.2 Probe conn
Page 146 and 147:
10 Measuring Cycles 10.3 Functional
Page 148 and 149:
10 Measuring Cycles 10.4 Start-up s
Page 150 and 151:
10 Measuring Cycles 10.4 Start-up s
Page 152 and 153:
10 Measuring Cycles 10.5 Machine da
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
11 Network Link 11.2 Linking Window
Page 160 and 161:
11 Network Link 11.2 Linking Window
Page 162 and 163:
12 Access Protection via Password a
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
13 Miscellaneous 13.1 Configuring t
Page 170 and 171:
13 Miscellaneous 13.2 Configuring t
Page 172 and 173:
13 Miscellaneous 13.3 Cylinder surf
Page 174 and 175:
13 Miscellaneous 13.3 Cylinder surf
Page 176 and 177:
13 Miscellaneous 13.4 Swivel heads
Page 178 and 179:
13 Miscellaneous 13.5 Multiple clam
Page 180 and 181:
13 Miscellaneous 13.7 Spindle contr
Page 182 and 183:
13 Miscellaneous 13.9 ShopMill Open
Page 184 and 185:
13 Miscellaneous 13.11 User status
Page 186 and 187:
13 Miscellaneous 13.12 OP hotkeys,
Page 188 and 189:
A Abbreviations MCP MD MMC MPF MPI
Page 190 and 191:
A Abbreviations A-190 Notes 12.01
Page 192 and 193:
B References User Documentation /AU
Page 194 and 195:
B References /PGT/ /PGZ/ /PI / /SYI
Page 196 and 197:
B References /FB3/ /FBA/ B-196 A4 D
Page 198 and 199:
B References /FBO/ /FBP/ /FBR/ /FBS
Page 200 and 201:
B References /PJU/ /POS1/ /POS2/ /P
Page 202 and 203:
B References B-202 Notes 12.01 Sie
Page 204 and 205:
C Index N NC machine data exact val
Page 206:
SINUMERIK 840D/810D Documentation o
show all

SINUMERIK 840D/810D ShopMill

Create successful ePaper yourself

Delete template?

Save as template?