SINUMERIK 840D/810D ShopMill

More documents

Recommendations

Info

6Machine Data 6.2 Display machine data for ShopMill 9721 $MM_CMM_ENABLE_TRACYL MD number Enable signal for cylinder peripheral surface transformation Default setting: 0 Min. input limit: 0 Max. input limit: 1 Changes valid from: IMMEDIATE Protection level: 3/4 Unit: - Data type: BYTE Valid as of software version: 840D SW 4.4, 810D SW 2.4 with ShopMill SW 5.1 Meaning: Activate the cylinder peripheral surface transformation function via the operator interface: 6-86 12.01 0 = The cylinder peripheral surface transformation function is not displayed on the operator interface. 1 = The cylinder peripheral surface transformation function is displayed on the operator interface. The cylinder peripheral surface transformation function can be used only if it has been started up as a standard function. References: /FB2/, M1, Kinematic Transformations 9723 $MM_CMM_ENABLE_SWIVELLING_HEAD MD number Enable swivelling heads Default setting: 0 Min. input limit: 0 Max. input limit: 1 Changes valid from: IMMEDIATE Protection level: 3/4 Unit: - Data type: BYTE Valid as of software version: 840D SW 4.4, 810D SW 2.4 with ShopMill SW 5.1 Meaning: This MD can be set to select whether or not swivel heads can be used on the machine. 0 = No screenforms supporting swivel heads are made available. 1 = Screenforms supporting swivel heads are made available. 9724 $MM_CMM_CIRCLE_RAPID_FEED MD number Rapid traverse feed for positioning on circular path Default setting: 5000 Min. input limit: 0 Max. input limit: 100000 Changes valid from: IMMEDIATE Protection level: 3/4 Unit: mm/min Data type: DOUBLE Valid as of software version: 840D SW 6.3, 810D SW 4.3 with ShopMill SW 6.2 Meaning: Use this MD to set the rapid traverse feed in mm/min for positioning on a circular path. Note For a description of the display machine data for measuring cycles, please refer to Section 10.5 “Machine data for execution of measuring cycles”. E Siemens AG, 2001. All rights reserved SINUMERIK 840D/810D Description of Functions ShopMill (FBSP) - 12.01 Edition J
Reserved Functions M functions The following functions are utilized by ShopMill and must not be assigned for other purposes. M functions with extended address: M[value]=90 M[value]=91 M90 and M91 are defaults and must be changed where required. 1. extended M address: DB82.DBB12 ext_m_cmd_1, default=90 Display MD 9684 CMM_M_CODE_TOOL_BITS_1, default=90 2. extended M address: DB82.DBB13 ext_m_cmd_2, default=91 Display MD 9685 CMM_M_CODE_TOOL_BITS_2, default=91 E Siemens AG, 2001. All rights reserved SINUMERIK 840D/810D Description of Functions ShopMill (FBSP) - 12.01 Edition 7 J 7-87
Page 1:
SINUMERIK 840D/810D Description of
Page 4 and 5:
SINUMERIK R Documentation Printing
Page 6 and 7:
Preface Searching aids Notes Warnin
Page 8 and 9:
Preface viii Notes 12.01 E Siemens
Page 10 and 11:
Contents x 12.01 7 Reserved Functio
Page 12 and 13:
Contents xii Notes 12.01 Siemens A
Page 14 and 15:
1Hardware 1.1 Hardware assembly Tab
Page 16 and 17:
1Hardware 1.2 Examples for assignin
Page 18 and 19:
2Installation and Start-Up 2.1 Prec
Page 20 and 21:
2Installation and Start-Up 2.2 Init
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
2Installation and Start-Up 2.3 Seri
Page 34 and 35:
3 Supplementary Conditions 3-34 Not
Page 36 and 37: 4PLCProgram 4.2 Example for OB1 and
Page 38 and 39: 4PLCProgram 4.2 Example for OB1 and
Page 40 and 41: 4PLCProgram 4.3 Overview of blocks
Page 42 and 43: 4PLCProgram 4.4 Description of bloc
Page 44 and 45: 4PLCProgram 4.4 Description of bloc
Page 46 and 47: 4PLCProgram 4.5 Standard interface
Page 48 and 49: 5SignalDescription 5.1 Overview of
Page 50 and 51: 5SignalDescription 5.1 Overview of
Page 52 and 53: 5SignalDescription 5.2 Description
Page 70 and 71: 6Machine Data 6.1 NC machine data f
Page 72 and 73: 6Machine Data 6.2 Display machine d
Page 88 and 89: 7 Reserved Functions 7-88 Notes 12.
Page 90 and 91: 8 Tools 8.1 Tool-changing cycle ada
Page 92 and 93: 8 Tools 8.2 Manual tools 8.2 Manual
Page 94 and 95: 8 Tools 8.4 Activate tool-specific
Page 96 and 97: 8 Tools 8.5 Modify texts for tool-s
Page 102 and 103: 9ToolManagement 9.1 Overview of fun
Page 104 and 105: 9ToolManagement 9.2 Start-up of the
Page 120 and 121: 9ToolManagement 9.3 Tool management
Page 130 and 131: 9ToolManagement 9.4 Examples 9.4 Ex
Page 132 and 133: 9ToolManagement 9.4 Examples Create
Page 134 and 135: 9ToolManagement 9.4 Examples 9-134
Page 136 and 137:
9ToolManagement 9.5 Configuring the
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
10 Measuring Cycles 10.2 Probe conn
Page 146 and 147:
10 Measuring Cycles 10.3 Functional
Page 148 and 149:
10 Measuring Cycles 10.4 Start-up s
Page 150 and 151:
10 Measuring Cycles 10.4 Start-up s
Page 152 and 153:
10 Measuring Cycles 10.5 Machine da
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
11 Network Link 11.2 Linking Window
Page 160 and 161:
11 Network Link 11.2 Linking Window
Page 162 and 163:
12 Access Protection via Password a
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
13 Miscellaneous 13.1 Configuring t
Page 170 and 171:
13 Miscellaneous 13.2 Configuring t
Page 172 and 173:
13 Miscellaneous 13.3 Cylinder surf
Page 174 and 175:
13 Miscellaneous 13.3 Cylinder surf
Page 176 and 177:
13 Miscellaneous 13.4 Swivel heads
Page 178 and 179:
13 Miscellaneous 13.5 Multiple clam
Page 180 and 181:
13 Miscellaneous 13.7 Spindle contr
Page 182 and 183:
13 Miscellaneous 13.9 ShopMill Open
Page 184 and 185:
13 Miscellaneous 13.11 User status
Page 186 and 187:
13 Miscellaneous 13.12 OP hotkeys,
Page 188 and 189:
A Abbreviations MCP MD MMC MPF MPI
Page 190 and 191:
A Abbreviations A-190 Notes 12.01
Page 192 and 193:
B References User Documentation /AU
Page 194 and 195:
B References /PGT/ /PGZ/ /PI / /SYI
Page 196 and 197:
B References /FB3/ /FBA/ B-196 A4 D
Page 198 and 199:
B References /FBO/ /FBP/ /FBR/ /FBS
Page 200 and 201:
B References /PJU/ /POS1/ /POS2/ /P
Page 202 and 203:
B References B-202 Notes 12.01 Sie
Page 204 and 205:
C Index N NC machine data exact val
Page 206:
SINUMERIK 840D/810D Documentation o
show all

SINUMERIK 840D/810D ShopMill

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?