SINUMERIK 840D/810D ShopMill

More documents

Recommendations

Info

13 Miscellaneous 13.3 Cylinder surface transformation 13-174 12.01 1st data block for cylinder surface transformation: 24100 $MC_TRAFO_TYPE_1=512 Definition of 1st transformation in cylinder surface channel 24110 $MC_TRAFO_AXES_IN_1[0]=3 Channel axis of radial rotary axis (Z) for 1st transformation 24110 $MC_TRAFO_AXES_IN_1[1]=4 Channel axis of rotary axis for 1st transformation 24110 $MC_TRAFO_AXES_IN_1[2]=1 Channel axis of parallel rotary axis (X) for 1st transformation 24110 $MC_TRAFO_AXES_IN_1[3]=2 Channel axis of special axis index [0] for 1st transformation 24120 $MC_TRAFO_GEOAX_ASSIGN_TAB_1[0]=1 1st Channel axis (X) for 1st transformation 24120 $MC_TRAFO_GEOAX_ASSIGN_TAB_1[1]=4 2nd Channel axis (Y) for 1st transformation 24120 $MC_TRAFO_GEOAX_ASSIGN_TAB_1[2]=3 3rd Channel axis (Z) for 1st transformation 24800 $MC_TRACYL_ROT_AX_OFFSET_1=0 Offset of rotary axis for the 1st TRACYL transformation 24810 $MC_TRACYL_ROT_SIGN_IS_PLUS_1=1 Sign of rotary axis for the 1st TRACYL transformation 24820 $MC_TRACYL_BASE_TOOL_1[n]=0 Vector of basic tool for 1st TRACYL transformation 2nd data block for cylinder surface transformation with slot side correction: 24200 $MC_TRAFO_TYPE_2=513 Definition of 2nd transformation in cylinder surface channel with slot side correction 24210 $MC_TRAFO_AXES_IN_2[0]=3 Channel axis of radial rotary axis (Z) for 2nd transformation 24210 $MC_TRAFO_AXES_IN_2[1]=4 Channel axis of rotary axis for 2nd transformation 24210 $MC_TRAFO_AXES_IN_2[2]=1 Channel axis of parallel rotary axis (X) for 2nd transformation 24210 $MC_TRAFO_AXES_IN_2[3]=2 Channel axis of special axis index [0] for 2nd transformation 24220 $MC_TRAFO_GEOAX_ASSIGN_TAB_2[0]=1 1st Channel axis (X) for 2nd transformation 24220 $MC_TRAFO_GEOAX_ASSIGN_TAB_2[1]=4 2nd channel axis (Y) for 2nd transformation 24220 $MC_TRAFO_GEOAX_ASSIGN_TAB_2[2]=3 3rd channel axis (Z) for 2nd transformation 24850 $MC_TRACYL_ROT_AX_OFFSET_2=0 Offset of rotary axis for 2nd TRACYL transformation 24860 $MC_TRACYL_ROT_SIGN_IS_PLUS_2=1 Sign of rotary axis for the 2nd TRACYL transformation 24870 $MC_TRACYL_BASE_TOOL[n]=0 Vector of basic tool for 2nd TRACYL transformation Note MD 24100 must always be set to 512 in the 1st data set and MD 24200 to 513 in the 2nd data set. E Siemens AG, 2001. All rights reserved SINUMERIK 840D/810D Description of Functions ShopMill (FBSP) - 12.01 Edition
12.01 Enable cylinder surface transformation E Siemens AG, 2001. All rights reserved SINUMERIK 840D/810D Description of Functions ShopMill (FBSP) - 12.01 Edition 13 Miscellaneous 13.3 Cylinder surface transformation The “Enable cylinder surface transformation” function is displayed on the Shop- Mill operator interface when display MD 9721 $MM_CMM_ENABLE_TRACYL is set to 1. The rotary axis involved in the cylinder surface transformation is displayed and programmed via display MD 9653 $MM_CMM_ENABLE_A_AXIS or 9720 $MM_CMM_ENABLE_B_AXIS. 13-175
Page 1:
SINUMERIK 840D/810D Description of
Page 4 and 5:
SINUMERIK R Documentation Printing
Page 6 and 7:
Preface Searching aids Notes Warnin
Page 8 and 9:
Preface viii Notes 12.01 E Siemens
Page 10 and 11:
Contents x 12.01 7 Reserved Functio
Page 12 and 13:
Contents xii Notes 12.01 Siemens A
Page 14 and 15:
1Hardware 1.1 Hardware assembly Tab
Page 16 and 17:
1Hardware 1.2 Examples for assignin
Page 18 and 19:
2Installation and Start-Up 2.1 Prec
Page 20 and 21:
2Installation and Start-Up 2.2 Init
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
2Installation and Start-Up 2.3 Seri
Page 34 and 35:
3 Supplementary Conditions 3-34 Not
Page 36 and 37:
4PLCProgram 4.2 Example for OB1 and
Page 38 and 39:
4PLCProgram 4.2 Example for OB1 and
Page 40 and 41:
4PLCProgram 4.3 Overview of blocks
Page 42 and 43:
4PLCProgram 4.4 Description of bloc
Page 44 and 45:
4PLCProgram 4.4 Description of bloc
Page 46 and 47:
4PLCProgram 4.5 Standard interface
Page 48 and 49:
5SignalDescription 5.1 Overview of
Page 50 and 51:
5SignalDescription 5.1 Overview of
Page 52 and 53:
5SignalDescription 5.2 Description
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
6Machine Data 6.1 NC machine data f
Page 72 and 73:
6Machine Data 6.2 Display machine d
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
7 Reserved Functions 7-88 Notes 12.
Page 90 and 91:
8 Tools 8.1 Tool-changing cycle ada
Page 92 and 93:
8 Tools 8.2 Manual tools 8.2 Manual
Page 94 and 95:
8 Tools 8.4 Activate tool-specific
Page 96 and 97:
8 Tools 8.5 Modify texts for tool-s
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
9ToolManagement 9.1 Overview of fun
Page 104 and 105:
9ToolManagement 9.2 Start-up of the
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
9ToolManagement 9.3 Tool management
Page 122 and 123:
9ToolManagement 9.3 Tool management
Page 124 and 125: 9ToolManagement 9.3 Tool management
Page 130 and 131: 9ToolManagement 9.4 Examples 9.4 Ex
Page 132 and 133: 9ToolManagement 9.4 Examples Create
Page 134 and 135: 9ToolManagement 9.4 Examples 9-134
Page 136 and 137: 9ToolManagement 9.5 Configuring the
Page 144 and 145: 10 Measuring Cycles 10.2 Probe conn
Page 146 and 147: 10 Measuring Cycles 10.3 Functional
Page 148 and 149: 10 Measuring Cycles 10.4 Start-up s
Page 150 and 151: 10 Measuring Cycles 10.4 Start-up s
Page 152 and 153: 10 Measuring Cycles 10.5 Machine da
Page 158 and 159: 11 Network Link 11.2 Linking Window
Page 160 and 161: 11 Network Link 11.2 Linking Window
Page 162 and 163: 12 Access Protection via Password a
Page 168 and 169: 13 Miscellaneous 13.1 Configuring t
Page 170 and 171: 13 Miscellaneous 13.2 Configuring t
Page 172 and 173: 13 Miscellaneous 13.3 Cylinder surf
Page 176 and 177: 13 Miscellaneous 13.4 Swivel heads
Page 178 and 179: 13 Miscellaneous 13.5 Multiple clam
Page 180 and 181: 13 Miscellaneous 13.7 Spindle contr
Page 182 and 183: 13 Miscellaneous 13.9 ShopMill Open
Page 184 and 185: 13 Miscellaneous 13.11 User status
Page 186 and 187: 13 Miscellaneous 13.12 OP hotkeys,
Page 188 and 189: A Abbreviations MCP MD MMC MPF MPI
Page 190 and 191: A Abbreviations A-190 Notes 12.01
Page 192 and 193: B References User Documentation /AU
Page 194 and 195: B References /PGT/ /PGZ/ /PI / /SYI
Page 196 and 197: B References /FB3/ /FBA/ B-196 A4 D
Page 198 and 199: B References /FBO/ /FBP/ /FBR/ /FBS
Page 200 and 201: B References /PJU/ /POS1/ /POS2/ /P
Page 202 and 203: B References B-202 Notes 12.01 Sie
Page 204 and 205: C Index N NC machine data exact val
Page 206: SINUMERIK 840D/810D Documentation o
show all

SINUMERIK 840D/810D ShopMill

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?