SINUMERIK 840D/810D ShopMill

More documents

Recommendations

Info

5SignalDescription 5.2 Description of ShopMill interface DB82 5-54 12.01 DB82 sub_mode_mill.oem2 DBX6.5 OEM2 operating area Data block Signal(s) to ShopMill Edge evaluation: yes Signal(s) updated: cyclically Signal(s) valid as of software version: 840D SW 6.1, 810D SW 4.1 Edge change 0 - - ->1 This signal can also be implemented in the user program via a customized key on the 19¨ machine control panel or via hardkeys on the full CNC keyboard in the case of an OP032S machine control panel. The appropriate operating area is displayed in ShopMill when you select this key. Signal state 0 No effect Corresponding to ... DB82, DBX34.5, sub_mode_mill.oem2 DB82 sub_mode_mill.customer DBX6.6 CUSTOMER operating area Data block Signal(s) to ShopMill Edge evaluation: yes Signal(s) updated: cyclically Signal(s) valid as of software version: 840D SW 6.1, 810D SW 4.1 Edge change 0 - - ->1 This signal can also be implemented in the user program via a customized key on the 19¨ machine control panel or via hardkeys on the full CNC keyboard in the case of an OP032S machine control panel. The appropriate operating area is displayed in ShopMill when you select this key. Signal state 0 No effect Corresponding to ... DB82, DBX34.6, sub_mode_mill.customer DB82 sub_mode_mill.mda DBX6.7 MDA operating area Data block Signal(s) to ShopMill Edge evaluation: yes Signal(s) updated: cyclically Signal(s) valid as of software version: 840D SW 6.1, 810D SW 4.1 Edge change 0 - - ->1 This signal can also be implemented in the user program via a customized key on the 19¨ machine control panel or via hardkeys on the full CNC keyboard in the case of an OP032S machine control panel. The appropriate operating area is displayed in ShopMill when you select this key. Signal state 0 No effect Note Effective only when DB82.DBB0=2 is set Corresponding to ... DB82, DBX34.7, sub_mode_mill.mda DB82 spindle_interface_number DBB8 Assignment of spindle/axis data record Data block Signal(s) to ShopMill Edge evaluation: no Signal(s) updated: cyclically Signal(s) valid as of software version: 840D SW 4.3, 810D SW 2.3 Signal meaning This signal can be used to assign the spindle to an axis data record. Enter the number of the machine axis. Corresponding to... ShopMill SW release 5.3 and higher: MD 9705 CMM_INDEX_SPINDLE, enter the number of the channel axis here. E Siemens AG, 2001. All rights reserved SINUMERIK 840D/810D Description of Functions ShopMill (FBSP) - 12.01 Edition
12.01 E Siemens AG, 2001. All rights reserved SINUMERIK 840D/810D Description of Functions ShopMill (FBSP) - 12.01 Edition 5SignalDescription 5.2 Description of ShopMill interface DB82 DB82 user_defined_spindle_control DBX9.0 User-defined spindle control Data block Signal(s) to ShopMill Edge evaluation: no Signal(s) updated: cyclically Signal(s) valid as of software version: 840D SW 6.2, 810D SW 4.2 Signal state 0 The spindle control is supported by the ShopMill PLC. Interface signals DB82.DBX9.1 to DB82.DBX9.4 and DB82.DBX36.2 to DB82.DBX36.5 are active. Interface signals DB3x.DBX30.0 to DB3x.DBX30.2 are written to the axis DB of the spindle (see also Section 13.7 “Spindle control”). Signal state 1 The spindle control is not supported by the ShopMill PLC. Interface signals DB82.DBX9.1 to DB82.DBX9.4 and DB82.DBX36.2 to DB82.DBX36.5 have no function and interface signals DB3x.DBX30.0 to DB3x.DBX30.2 are not written. The spindle must be controlled in the user PLC. DB82 spindle_start DBX9.1 Spindle Start Data block Signal(s) to ShopMill Edge evaluation: yes Signal(s) updated: cyclically Signal(s) valid as of software version: 840D SW 4.3, 810D SW 2.3 Edge change 0 ---> 1 The spindle starts only when a direction of rotation is selected via interface signals DB3x.DBX30.1 or DB3x.DBX30.2. Please refer to Section 13.7 “Spindle control”. Signal state 0 No effect Corresponding to ... DB82, DBX36.2, spindle_start_req DB82, DBX9.3, spindle_left DB82, DBX9.4, spindle_right DB82 spindle_stop DBX9.2 Spindle Stop Data block Signal(s) to ShopMill Edge evaluation: yes Signal(s) updated: cyclically Signal(s) valid as of software version: 840D SW 4.3, 810D SW 2.3 Edge change The spindle is stopped via interface signal DB3x.DBX30.0. 0 ---> 1 Please refer to Section 13.7 “Spindle control”. Signal state 0 No effect Corresponding to ... DB82, DBX36.3, spindle_stop_req DB82 spindle_left DBX9.3 Spindle rotation counter-clockwise Data block Signal(s) to ShopMill Edge evaluation: yes Signal(s) updated: cyclically Signal(s) valid as of software version: 840D SW 4.3, 810D SW 2.3 Edge change 0 ---> 1 Direction of spindle rotation (CCW) works only in conjunction with Spindle Start. Signal state 0 No effect Corresponding to ... DB82, DBX36.5, spindle_left References /BAS/, ShopMill Operator’s Guide 5-55
Page 1:
SINUMERIK 840D/810D Description of
Page 4 and 5: SINUMERIK R Documentation Printing
Page 6 and 7: Preface Searching aids Notes Warnin
Page 8 and 9: Preface viii Notes 12.01 E Siemens
Page 10 and 11: Contents x 12.01 7 Reserved Functio
Page 12 and 13: Contents xii Notes 12.01 Siemens A
Page 14 and 15: 1Hardware 1.1 Hardware assembly Tab
Page 16 and 17: 1Hardware 1.2 Examples for assignin
Page 18 and 19: 2Installation and Start-Up 2.1 Prec
Page 20 and 21: 2Installation and Start-Up 2.2 Init
Page 32 and 33: 2Installation and Start-Up 2.3 Seri
Page 34 and 35: 3 Supplementary Conditions 3-34 Not
Page 36 and 37: 4PLCProgram 4.2 Example for OB1 and
Page 38 and 39: 4PLCProgram 4.2 Example for OB1 and
Page 40 and 41: 4PLCProgram 4.3 Overview of blocks
Page 42 and 43: 4PLCProgram 4.4 Description of bloc
Page 44 and 45: 4PLCProgram 4.4 Description of bloc
Page 46 and 47: 4PLCProgram 4.5 Standard interface
Page 48 and 49: 5SignalDescription 5.1 Overview of
Page 50 and 51: 5SignalDescription 5.1 Overview of
Page 52 and 53: 5SignalDescription 5.2 Description
Page 70 and 71: 6Machine Data 6.1 NC machine data f
Page 72 and 73: 6Machine Data 6.2 Display machine d
Page 88 and 89: 7 Reserved Functions 7-88 Notes 12.
Page 90 and 91: 8 Tools 8.1 Tool-changing cycle ada
Page 92 and 93: 8 Tools 8.2 Manual tools 8.2 Manual
Page 94 and 95: 8 Tools 8.4 Activate tool-specific
Page 96 and 97: 8 Tools 8.5 Modify texts for tool-s
Page 102 and 103: 9ToolManagement 9.1 Overview of fun
Page 104 and 105:
9ToolManagement 9.2 Start-up of the
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
9ToolManagement 9.3 Tool management
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
9ToolManagement 9.4 Examples 9.4 Ex
Page 132 and 133:
9ToolManagement 9.4 Examples Create
Page 134 and 135:
9ToolManagement 9.4 Examples 9-134
Page 136 and 137:
9ToolManagement 9.5 Configuring the
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
10 Measuring Cycles 10.2 Probe conn
Page 146 and 147:
10 Measuring Cycles 10.3 Functional
Page 148 and 149:
10 Measuring Cycles 10.4 Start-up s
Page 150 and 151:
10 Measuring Cycles 10.4 Start-up s
Page 152 and 153:
10 Measuring Cycles 10.5 Machine da
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
11 Network Link 11.2 Linking Window
Page 160 and 161:
11 Network Link 11.2 Linking Window
Page 162 and 163:
12 Access Protection via Password a
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
13 Miscellaneous 13.1 Configuring t
Page 170 and 171:
13 Miscellaneous 13.2 Configuring t
Page 172 and 173:
13 Miscellaneous 13.3 Cylinder surf
Page 174 and 175:
13 Miscellaneous 13.3 Cylinder surf
Page 176 and 177:
13 Miscellaneous 13.4 Swivel heads
Page 178 and 179:
13 Miscellaneous 13.5 Multiple clam
Page 180 and 181:
13 Miscellaneous 13.7 Spindle contr
Page 182 and 183:
13 Miscellaneous 13.9 ShopMill Open
Page 184 and 185:
13 Miscellaneous 13.11 User status
Page 186 and 187:
13 Miscellaneous 13.12 OP hotkeys,
Page 188 and 189:
A Abbreviations MCP MD MMC MPF MPI
Page 190 and 191:
A Abbreviations A-190 Notes 12.01
Page 192 and 193:
B References User Documentation /AU
Page 194 and 195:
B References /PGT/ /PGZ/ /PI / /SYI
Page 196 and 197:
B References /FB3/ /FBA/ B-196 A4 D
Page 198 and 199:
B References /FBO/ /FBP/ /FBR/ /FBS
Page 200 and 201:
B References /PJU/ /POS1/ /POS2/ /P
Page 202 and 203:
B References B-202 Notes 12.01 Sie
Page 204 and 205:
C Index N NC machine data exact val
Page 206:
SINUMERIK 840D/810D Documentation o
show all

SINUMERIK 840D/810D ShopMill

Create successful ePaper yourself

Delete template?

Save as template?