<strong>STEPP</strong>CONFIG VERSION 1.8.14 $PSRF108,LOG $PSRF108,VOL $PSRF108,KEY $PSRF108,NAME $PSRF108,PORT $PSRF109,0,Date,Time $PSRF103,Protocol,00,0 0,On/OFF,01 $PSRF108,IN $PSRF108,Fehler! Verweisquelle konnte nicht gefunden werden. $PSRF108,GSMRESET() Define the History parameters Modify the level of the speaker of the <strong>STEPP</strong> Configure the alarm inputs of the <strong>STEPP</strong> Give/Change <strong>STEPP</strong> name Set the digital outputs Retrieve History <strong>for</strong> specific date/Time Switch ON/OFF GPS/GPGSM/GPIOP protocols Configure the analog inputs with the max. and min. values Reset the GPS core in the <strong>STEPP</strong> after nminutes if no satellites in view Reset the GSM core after n-minutes if no data can be transmitted via data connection It allows you to monitor an abandoned $PSRF108,IGN() vehicle fitted with <strong>Falcom</strong> <strong>STEPP</strong> Configure geo-fencing vial NMEA <strong>commands</strong> $PSRF108,GEO() = RegionName, Region ID,Lattitude UL, Longitude UL, Latitude LR, Longitude LR, 0 $PSRF108, GEO() = RegionName, Region ID,Lattitude UL, Longitude UL, Latitude LR,Longitude LR, 1 $PSRF108, GEO() = RegionName, Region ID,Lattitude UL, Geo-Fencing command Alarm when <strong>STEPP</strong> leaves the area Geo-Fencing command Alarm when the <strong>STEPP</strong> enters the area Geo-Fencing command Alarm when <strong>STEPP</strong> enters and leaves the area $PSRF108,LOG=4,60,3600,50,0,20,0 $PSRF108,VOL=12,14 Speaker: 12 Microphone: 14 $PSRF108,KEY1=S0123456,AlarmText,RM C $PSRF108,NAME=VEHICLE001 $PSRF108,PORT1=E Output1 ON $PSRF108,PORT2=A Output2 OFF $PSRF108,PORT3=Z,1,1 Output3 cycle switching (1 sec. ON; 1 sec. OFF) $PSRF108,PORT4=I,2,1 Impulse signal at output4 (2 sec. Signal impulse; 1 is ignored but required <strong>for</strong> settings) $PSRF109,0,280104,155000 $PSRF103,04,00,00,01 GPRMC OFF $PSRF103,04,00,01,01 GPRMC ON $PSRF108,IN1=S012345,AlarmText,2,4,IOP $PSRF108,GPSRESET=5 $PSRF108,GSMRESET=1 $PSRF108,IGN=0,1000,Ignition-alarm*25 A Master region (GEO00) of 1000 meter radius is generated. $PSRF108,GEO01=LANGEWIESEN,001,50 .68175,10.95133,50.66715,10.98726,0 $PSRF108,GEO01=LANGEWIESEN,001,50 .68175,10.95133,50.66715,10.98726,1 $PSRF108,GEO01=LANGEWIESEN,001,50 .68175,10.95133,50.66715,10.98726,2 This confidential document is the property of FALCOM GmbH and may not be copied or circulated without permission. Page 25
<strong>STEPP</strong>CONFIG VERSION 1.8.14 Longitude UL, Latitude LR, Longitude LR, 2 This confidential document is the property of FALCOM GmbH and may not be copied or circulated without permission. Page 26