6 Configuration commands - for Falcom STEPP
6 Configuration commands - for Falcom STEPP
6 Configuration commands - for Falcom STEPP
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>STEPP</strong>CONFIG VERSION 1.8.14<br />
SMS<br />
command<br />
NMEA<br />
message<br />
&CNF [PWD] UNIT IGN=0,1000,Ignition-alarm<br />
&CNF [PWD] UNIT IGN=0,1000,Ignition-alarm:GEOMSG=<br />
S012345678,3,60,0,0,0,0,0,IOPRMC<br />
&CNF UNIT IGN<br />
&CNF UNIT IGN:GEOMSG<br />
$PSRF108,IGN=0,1000,Ignition-alarm*25<br />
$PSRF108,IGN=0,1000,Ignition-alarm:GEOMSG=<br />
S012345678,3,60,0,0,0,0,0,IOPRMC*52<br />
$PSRF108,IGN*42<br />
$PSRF108,IGN:GEOMSG*6C<br />
Notes<br />
• A SMS alarm message is issued, if the vehicle fitted with <strong>STEPP</strong><br />
moves beyond the user-defined master region. Please, note that, if<br />
master region is activated, other set areas are deactivated.<br />
• If the value is set to 0, then the device deactivates the master<br />
region and automatically activates the other set areas (if defined).<br />
• !!!! Please note that you have to configure first the destination number<br />
where the SMS alarm should be sent to. This could be done by using<br />
the command:<br />
&CNF UNIT GEOMSG=S012345678,3,60,0,0,0,0,0,IOPRMC<br />
(this is only an example, other configuration events are also possible).<br />
Finally configure the Master region via SMS command.<br />
• In order to configure a Master region and set the GEOMSG settings at<br />
once (instead of the user at first configures the GEOMSG parameter<br />
and then initialize the Master region), you can send both parameters<br />
(split by colons [:]) the IGN and GEOMSG with corresponding settings<br />
on one line, (see example in table above).<br />
• To clear the present configuration of IGN, a SMS message without<br />
value has to be sent to the device.<br />
• The user may also clear the present configuration of IGN and<br />
GEOMSG at once, see the last example in the table above.<br />
• If the object (vehicle fitted with the FALCOM <strong>STEPP</strong>) enters (i) into the<br />
predefined master region, the SMS message delivered from the <strong>STEPP</strong><br />
device to the target phone number specified by the<br />
GEOMSG parameter includes:<br />
- the device name (if predefined),<br />
- the header (GEO00),<br />
- the specified by the WATCH parameter and<br />
- closed by the user selected protocols either by the WATCH or<br />
GEOMSG parameter.<br />
e.g.<br />
+CMT: "+4917610022382",,"05/06/27,10:44:20+08"<br />
<strong>STEPP</strong> Ignition-alarm<br />
$GPRMC,084509.984,A,5040.3998,N,01058.8412,E,0.06,350.84,<br />
270605,,*05<br />
$GPIOP,11000000,00000000,0.71,5.25,4.11*73<br />
i<br />
Feature of the Firmware 1.8.14 and greater versions<br />
This confidential document is the property of FALCOM GmbH and may not be copied or circulated without permission.<br />
Page 96