6 Configuration commands - for Falcom STEPP
6 Configuration commands - for Falcom STEPP
6 Configuration commands - for Falcom STEPP
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>STEPP</strong>CONFIG VERSION 1.8.14<br />
Version history:<br />
Version<br />
number<br />
Author Changes<br />
1.00 Fadil Beqiri - Initial version<br />
1.01 Fadil Beqiri - Connection illustration (Image 26) optimize.<br />
1.02 Saleh Mohamad - Command on page 67 corrected<br />
- Added new chapter “4.2.3.1.4 Analogue imputs configuration”.<br />
- Added new SMS <strong>commands</strong> (POS polling positions and START<br />
reset GPS receiver and GSM engine).<br />
1.2 RC3 Fadil Beqiri<br />
-<br />
-<br />
The parameter LOG corrected<br />
The parameter KEY corrected (added)<br />
- The description of chapter 6.4.7 corrected.<br />
-<br />
-<br />
The received alarm SMS from is corrected (added)<br />
On the chapter 6.1.2 the command $PSRF109 is corrected.<br />
- New feature <strong>for</strong> Yellow LED added<br />
- New chapter “<strong>Falcom</strong> <strong>STEPP</strong> operating with Firmware 1.4 “<br />
included new SMS <strong>commands</strong> added.<br />
- “Important item “ to “Service Mode” menu added.<br />
- New NOTE added<br />
- Chapters 4.1, 4.2.1, 4.2.3, 4.2.3.2, 4.3 updated<br />
- An image description (of each bit) of $GPIOP protocol added<br />
- “Logging” menu item is added instead of “Switch ON<br />
Development Console”, which is removed.<br />
- In the chapter 3.3.1.4, the example of modem profile the<br />
parameters Register Status and GSM-Status updated.<br />
- Figures 9, 10, 12 and 18.b updated.<br />
1.4 Fadil Beqiri<br />
-<br />
-<br />
Chaper 4.3.4 History window updated, new figure added.<br />
Pin 14 in Image 27 added.<br />
- In the chapter 4.2 page 63, Please note updated, new feature <strong>for</strong><br />
password encryption added.<br />
- New SMS parameter “MSG“added.<br />
- Chapter 6.4.7 updated.<br />
- It is possible to transfer data to other modem/mobile using the<br />
command described in chapter 6.4.6.<br />
- An Example is added in the received alarm SMS from <strong>STEPP</strong>.<br />
- A simple Public procedure to calculate the Checksum is<br />
added.<br />
- The “SIM” with corresponding solution on page 74 added.<br />
- New chapter “How to update the new firmware into the<br />
<strong>STEPP</strong>“ is added.<br />
1.4.1 Fadil Beqiri<br />
- The SMS configuration parameter “IN” <strong>for</strong> Analogue<br />
Inputs added.<br />
- New chapter 2.1.4 added (periodically self test on the <strong>Falcom</strong><br />
<strong>STEPP</strong> firmware Ver. 1.4.5 implemented).<br />
- New chapter 3 added (Brief description of supported SMS and<br />
1.4.2 Fadil Beqiri<br />
-<br />
PSRF <strong>commands</strong>)<br />
The NMEA command $PSRF107 disabled. (!!!! Please do not<br />
try to per<strong>for</strong>m this command.)<br />
- The chapter 6.4.1 updated. The SMS parameters MSG and the<br />
PSRF command in the chapter 6.5.1 updated.<br />
This confidential document is the property of FALCOM GmbH and may not be copied or circulated without permission.<br />
Page 4