6 Configuration commands - for Falcom STEPP
6 Configuration commands - for Falcom STEPP
6 Configuration commands - for Falcom STEPP
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>STEPP</strong>CONFIG VERSION 1.8.14<br />
Lower Right (2)<br />
character (°) is produce when the "Alt" key is released.<br />
Enter the lower right coordinates <strong>for</strong> the Latitude and Longitude<br />
of the restricted zone.<br />
Area (3) Select one of 99 possibilities to defined an area.<br />
Enter the identification number <strong>for</strong> each areas.<br />
There are two possibilities to set up an ID zone.<br />
Area ID (4)<br />
In order to establish a single zone which involves many small<br />
zones (up to 99 fixed), is required that all involved zones must<br />
have the same ID number. e.g. establish an area where the<br />
vehicle allowed to travel. An alarm message is issued if predefined<br />
parameters of established single zone are exceeded. (For<br />
more details read the description below this table.)<br />
In order to control each zone separately, the different ID <strong>for</strong> each<br />
zone has to be set. An alarm message is issued if pre-defined<br />
parameters <strong>for</strong> current zone are exceeded.<br />
Alarm type (5)<br />
Select one of three posibilities of alarm type <strong>for</strong> current restricted<br />
zone. (For more details read the description below.)<br />
Alarm text (6) Enter the text of the alarm SMS <strong>for</strong> current defined zone.<br />
Dest. number (7)<br />
Enter the target telephone number where an alarm <strong>for</strong> current<br />
zone to be sent to.<br />
Set the interval of time in seconds <strong>for</strong> sending SMS message<br />
Interval (8)<br />
from the <strong>Falcom</strong> <strong>STEPP</strong>. If this value is set to 0, a SMS message<br />
<strong>for</strong> in-zone and out-zone will be sent to the authorized number,<br />
respectively.<br />
Send (9)<br />
Saves the configuration of the restricted zone in <strong>Falcom</strong> <strong>STEPP</strong><br />
terminal.<br />
Appears all stored configuration of areas. By double-clicking on<br />
Stored areas (10) an already defined area, the area data will be displayed in fields 1<br />
to 9 <strong>for</strong> controlling and editing purposes.<br />
Concerning the set No-Go Zone Entry event, the FALCOM <strong>STEPP</strong> terminal<br />
supports three different configuration types:<br />
1- if the vehicle enters (on the Alarm Type selection field named “inside”)<br />
the pre-defined zone.<br />
2- if the vehicle leaves (on the Alarm Type selection field named“outside”)<br />
the pre-defined zone.<br />
3- if the vehicle enters and leaves (on the Alarm Type selection field named<br />
“inside and outside”) the pre-defined zone.<br />
The other possibility is also supported, when the user sets up to 99 different<br />
zones with the same ID number. The FALCOM <strong>STEPP</strong> recognises those<br />
restricted zones as a single zone. The set up of zones has to be adjacent to or<br />
overlapped zones (no free space between zones). That means if the vehicle<br />
leaves the first zone and at the same time enters to the next one and others,<br />
(depend on the amount of set zones) the FALCOM <strong>STEPP</strong> compares the ID<br />
zones (the previous zone with the next one) if they are the same one, no SMS<br />
message will be sent. When the vehicle leaves the current zone and does not<br />
contemporaneously enter to the next one, so a SMS alert message with<br />
corresponding zone identification text will be sent to the predefined phone<br />
number. In other words this geo-fencing feature allows you to establish an area<br />
This confidential document is the property of FALCOM GmbH and may not be copied or circulated without permission.<br />
Page 44