Tooling Systems

Slim design.
Pre-balanced G6.3 @ 15,000 rpm.
Maximum 30,000 rpm.
Manufactured runout ≤0,003mm (.0001").
Through-the-toolholder coolant capability.
Chucks ≤ ø 10mm (≤ ø 3/8") have 10mm
(3/8") axial adjustment stop actuated
through the center of chuck.
Chucks ≥ ø 12mm (≥ ø 1/2") have external
side actuation adjustment stop, giving
10mm (3/8") axial adjustment.
KM63UT Shank Tools
Hydraulic Chucks — Slim Line
KM SYSTEM
HSK SYSTEM
BT SYSTEM
HCSLT — Metric
order number catalog number D1 D2 D21 D22 L1 L2 L9 L21 V kg
3055503 KM63UTHCSLT06160M 6 13,5 19,50 44,45 160 35 27 85 10 1,36
3055504 KM63UTHCSLT08160M 8 15,5 19,50 44,45 160 35 27 85 10 1,37
3055505 KM63UTHCSLT10160M 10 17,5 44,45 — 160 85 31 140 10 1,35
CV SYSTEM
Spare Parts
catalog number
actuation
wrench
wrench sizeactuation
screw
adjustment
wrench
wrench sizeadjustment
screw
KM63UTHCSLT06160M 170.135 5 MM 170.002 2.5 MM
KM63UTHCSLT08160M 170.135 5 MM 170.002 2.5 MM
KM63UTHCSLT10160M 170.135 5 MM 170.003 3 MM
DV SYSTEM
QC / R8 SYSTEMS
STRAIGHT SHANK
HCSL — Metric
order number catalog number D1 D2 D21 L1 L2 L9 V kg
3055506 KM63UTHCSL12170M 12 19,5 44,45 170 95 36 10 1,40
3055507 KM63UTHCSL14170M 14 21,5 52,45 170 95 36 10 1,66
3055508 KM63UTHCSL16170M 16 23,5 52,45 170 95 39 10 1,67
3055509 KM63UTHCSL18170M 18 25,5 52,45 170 95 39 10 1,71
3055510 KM63UTHCSL20170M 20 27,5 52,45 170 95 41 10 1,75
Spare Parts
catalog number
actuation
wrench
wrench sizeactuation
screw
adjustment
wrench
wrench sizeadjustment
screw
KM63UTHCSL12170M 170.135 5 MM 170.002 2.5 MM
KM63UTHCSL14170M 170.135 5 MM 170.002 2.5 MM
KM63UTHCSL16170M 170.135 5 MM 170.002 2.5 MM
KM63UTHCSL18170M 170.135 5 MM 170.002 2.5 MM
KM63UTHCSL20170M 170.135 5 MM 170.002 2.5 MM
COLLETS / SLEEVES
INDEX TECHNICAL ACCESSORIES
IMPORTANT: Do not overtorque clamp screw. Use supplied wrench and tighten by hand until stop is felt.
Hydraulic chuck technical section, see page 805.
Supplied with stop screw and actuation wrench (in some cases these are the same wrench).
SEFAS chamfering rings are available and must be ordered separately; see Kennametal's Holemaking catalog.
Reduction sleeves are available and must be ordered separately; see page 643.
To place an order, contact Kennametal or your authorized Kennametal distributor, or visit www.kennametal.com. 303