Tooling Systems

Grip 1:1.
Industry-standard Erickson double-angle
collet system.
Recommended only for stationary
applications (lathe).
Toolholder provides 0,25mm (.010")
movement in all directions to compensate
for angular and parallel misalignments.
Hollow design enables coolant through
the tool and short projection lengths.
Adjusting nut varies spring tension to
compensate for cutter weight.
Collet Capacity
mm inch
DA - 08 Collet Series min. max. min. max.
DA180 2,2 20 1/64 3/4
DA 08 FF-SS — Inch
Straight Shank Tools
DA — 08 series — Double Angle — Fully Floating Holders
CV SYSTEM
BT SYSTEM
HSK SYSTEM KM SYSTEM
D order number catalog number
CST
collet series D11 D2 L LS lbs. locknut
locknut
wrench ft.lbs
3/4 1015975 SS075FC188688 DA180 1.73 2.38 6.88 4.00 .86 NPA188 OEW150 75
1 1015982 SS100FC188688 DA180 1.73 2.38 6.88 4.00 1.52 NPA188 OEW150 75
1 1/4 1015910 SS125FC188888 DA180 1.73 2.38 8.88 6.00 4.08 NPA188 OEW150 75
1 1/2 1015952 SS150FC188688 DA180 1.73 2.38 6.88 4.00 3.44 NPA188 OEW150 75
1 1/2 1015947 SS150FC188888 DA180 1.73 2.38 8.88 6.00 4.44 NPA188 OEW150 75
1 3/4 1015976 SS175FC188888 DA180 1.73 2.38 8.88 6.00 6.04 NPA188 OEW150 75
IMPORTANT: Do not overtighten locknut; use torque recommendations above.
Locknut and adjusting nut wrenches must be ordered separately.
Collet chuck technical section, see page 816.
Supplied with locknut.
DA standard straight-bore collets, see page 713.
No through-the-toolholder coolant
capability.
One adapter accepts a variety of slotting
cutter hub widths.
Works best in Kennametal-brand end mill
adapters and collet chucks.
Hub widths may vary in thickness so more
than one spacer may be required.
SA-SS — Inch
D order number catalog number D1 D2 L1 LS L13 lbs.
lock
screw
wrench sizelock
screw ft.lbs slot drive key
1 1288235 SS100SA062050 5/8 1.25 .50 2.28 .78 .74 KLS07 1/4 45 DWG SDK062088
1 1/4 1288264 SS125SA100075 1 1.61 .75 2.28 .94 1.46 KLS10 5/16 60 DWG SDK100106
1 1/4 1015362 SS125SA125075 1 1/4 1.86 .75 2.28 1.09 1.94 KLS12 5/16 70 DWG SDK125119
1 1/2 1015363 SS150SA150100 1 1/2 2.11 1.00 2.69 1.70 3.28 KLS15 3/8 75 DWG SDK150175
2 1015384 SS200SA200100 2 2.75 1.00 3.25 1.70 7.81 KLS20 9/16 100 SDK200169
IMPORTANT: Do not overtighten lock screw; use torque recommendations above.
Item 1288264 is supplied with .156" spacer.
Item 1015362 is supplied with .250" spacer.
Supplied with lock screw and drive key.
Lock screw wrench not included.
Slotting Cutter Adapters
INDEX TECHNICAL ACCESSORIES COLLETS / SLEEVES STRAIGHT SHANK QC / R8 SYSTEMS DV SYSTEM
To place an order, contact Kennametal or your authorized Kennametal distributor, or visit www.kennametal.com. 639