Tooling Systems

KM SYSTEM
HSK SYSTEM
BT SYSTEM
CV SYSTEM
DV SYSTEM
QC / R8 SYSTEMS
STRAIGHT SHANK
COLLETS / SLEEVES
INDEX TECHNICAL ACCESSORIES
Collets and Sleeves
32mm HC Hydraulic Chuck Sleeves
One-piece design with slot configuration to
seal coolant.
Cutting tool must be cylindrical and have a
through hole when using coolant.
Capable of up to 120 bar (1,500 psi)
coolant pressure.
Sleeve must be inserted completely into
the hydraulic chuck until shoulder mates
against the hydraulic chuck front face.
Cutting tools must be in full contact of the
sleeve bore length (L9).
Cutting tool shank requirement tolerance is
h6 and Ra ≥ 0,3 µm (12 µ in) surface finish.
Metric and inch bores are available.
HC32M Sleeve — Metric
(32mm sleeve with metric bore)
D1 order number catalog number
sleeve
series
sleeve capacity
max. mm
sleeve capacity
min. mm
L9
6,0 3026675 32MHC060M HC32M 6,000 5,992 37
7,0 3026676 32MHC070M HC32M 7,000 6,991 37
8,0 3026677 32MHC080M HC32M 8,000 7,991 37
9,0 3026678 32MHC090M HC32M 9,000 8,991 37
10,0 3026679 32MHC100M HC32M 10,000 9,991 40
11,0 3026680 32MHC110M HC32M 11,000 10,989 41
12,0 3026681 32MHC120M HC32M 12,000 11,989 45
13,0 3026682 32MHC130M HC32M 13,000 12,989 45
14,0 3026683 32MHC140M HC32M 14,000 13,989 46
15,0 3026684 32MHC150M HC32M 15,000 14,989 46
16,0 3026685 32MHC160M HC32M 16,000 15,989 48
17,0 3026686 32MHC170M HC32M 17,000 16,989 48
18,0 3026687 32MHC180M HC32M 18,000 12,989 49
19,0 3026691 32MHC190M HC32M 19,000 18,987 49
20,0 3026688 32MHC200M HC32M 20,000 19,987 50
22,0 3026689 32MHC220M HC32M 22,000 21,987 51
25,0 3026690 32MHC250M HC32M 25,000 24,987 57
HC32M Sleeve — Inch
(32mm sleeve with inch bore)
D1 order number catalog number
sleeve
series
sleeve capacity
max. inch
sleeve capacity
min. inch
L9
1/2 1093594 32HCM0500 HC32M .5000 .4996 1.77
9/16 1093595 32HCM0562 HC32M .5625 .5621 1.81
5/8 1093596 32HCM0625 HC32M .6250 .6246 1.81
11/16 1093597 32HCM0688 HC32M .6875 .6871 1.89
3/4 1093598 32HCM0750 HC32M .7500 .7495 1.97
7/8 1093599 32HCM0875 HC32M .8750 .8745 2.01
1 1093600 32HCM1000 HC32M 1.0000 .9995 2.20
IMPORTANT: Inserting the cutting tool less than the full gripping length (L9) of the sleeve can permanently damage the sleeve and hydraulic chuck.
Full length of the gripping bore needs to be maintained to achieve maximum accuracy, safety, and coolant sealing feature.
646
To place an order, contact Kennametal or your authorized Kennametal distributor, or visit www.kennametal.com.