Tooling Systems

DV SYSTEM
CV SYSTEM
BT SYSTEM
HSK SYSTEM KM SYSTEM
KM63XMZ Shank Tools
Hydraulic Chucks — Slim Line
Slim design.
Pre-balanced G6.3 @ 15,000 rpm.
Maximum 30,000 rpm.
Manufactured runout ≤ 0,003mm (.0001").
Through-the-toolholder coolant capability.
Chucks ≤ ø 10mm (≤ ø 3/8") have 10mm (3/8") axial adjustment stop
actuated through the center of chuck.
Chucks ≥ ø 12mm (≥ ø 1/2") have external side actuation adjustment
stop, giving 10mm (3/8") axial adjustment.
HCSLT — Metric
order number catalog number D1 D2 D21 D22 L1 L2 L9 L21 V
3055511 KM63XMZHCSLT06160MY 6 13,5 19,50 44,45 160 35 27 85,000 10,000
3055512 KM63XMZHCSLT08160MY 8 15,5 19,50 44,45 160 35 27 85,000 10,000
3055513 KM63XMZHCSLT10160MY 10 17,5 44,45 — 160 85 31 142,000 10,000
Spare Parts
catalog number
wrench sizeactuation
screw actuation wrench
wrench sizestop
screw adjustment wrench kg
KM63XMZHCSLT06160MY 5 MM 170.135 2.5 MM 170.002 1,38
KM63XMZHCSLT08160MY 5 MM 170.135 2.5 MM 170.002 1,39
KM63XMZHCSLT10160MY 5 MM 170.135 3 MM 170.003 1,37
STRAIGHT SHANK
QC / R8 SYSTEMS
COLLETS / SLEEVES
INDEX TECHNICAL ACCESSORIES
HCSL — Metric
order number catalog number D1 D2 D21 L1 L2 L9 V
3055514 KM63XMZHCSL12170MY 12 19,5 44,45 170 95 36 10
3055515 KM63XMZHCSL14170MY 14 21,5 52,45 170 95 36 10
3055516 KM63XMZHCSL16170MY 16 23,5 52,45 170 95 39 10
3055517 KM63XMZHCSL18170MY 18 25,5 52,45 170 95 39 10
3055518 KM63XMZHCSL20170MY 20 27,5 52,45 170 95 41 10
Spare Parts
catalog number
wrench sizeactuation
screw actuation wrench
wrench sizestop
screw adjustment wrench kg
KM63XMZHCSL12170MY 5 MM 170.135 2.5 MM 170.002 1,41
KM63XMZHCSL14170MY 5 MM 170.135 2.5 MM 170.002 1,69
KM63XMZHCSL16170MY 5 MM 170.135 2.5 MM 170.002 1,70
KM63XMZHCSL18170MY 5 MM 170.135 2.5 MM 170.002 1,75
KM63XMZHCSL20170MY 5 MM 170.135 2.5 MM 170.002 1,78
IMPORTANT: Do not overtorque clamp screw. Use supplied wrench and tighten by hand until stop is felt.
Hydraulic chuck technical section, see page 805.
Supplied with stop screw and actuation wrench (in some cases these are the same wrench).
SEFAS chamfering rings are available and must be ordered separately; see Kennametal's Holemaking catalog.
Reduction sleeves are available and must be ordered separately; see page 643.
328
To place an order, contact Kennametal or your authorized Kennametal distributor, or visit www.kennametal.com.