Tooling Systems

Chucks ≤ ø 12mm (≤ ø 1/2") are
pre-balanced G6.3 @ 30,000 rpm.
Chucks ≥ ø 14mm (≥ ø 5/8") are
pre-balanced G6.3 @ 30,000 rpm.
Runout ≤0,003mm (.0001").
Through-the-toolholder coolant capability.
10mm (3/8") axial adjustment stop through
center of tool.
HSK 40E Shank Tools
Hydraulic Chucks — Trend Line
KM SYSTEM
HSK SYSTEM
HC Trend-HSK form E — Metric
order number catalog number D1 D2 D21 L1 L2 L9 V kg
actuation
wrench
wrench sizeactuation
screw
stop screw
wrench
wrench sizestop
screw
2288133 HSK40EHCT06080M 6 25,7 32 80 35 27 10 0,47 170.135 5 MM 170.003 3 MM
2288134 HSK40EHCT08080M 8 27,7 32 80 36 27 10 0,49 170.135 5 MM 170.003 3 MM
2288135 HSK40EHCT10085M 10 29,7 32 85 38 31 10 0,53 170.135 5 MM 170.003 3 MM
2288136 HSK40EHCT12090M 12 31,6 32 90 40 36 10 0,57 170.135 5 MM 170.003 3 MM
2387467 HSK40EHCT14100M 14 33,6 50 100 42 36 10 0,80 170.135 5 MM 170.135 5 MM
2387468 HSK40EHCT16100M 16 37,6 50 100 47 39 10 0,85 170.135 5 MM 170.135 5 MM
2387469 HSK40EHCT18100M 18 39,6 50 100 47 39 10 0,87 170.135 5 MM 170.135 5 MM
2387470 HSK40EHCT20100M 20 41,6 50 100 48 41 10 0,89 170.135 5 MM 170.135 5 MM
HC Trend-HSK form E — Inch
order number catalog number D1 D2 D21 L1 L2 L9 V lbs.
actuation
wrench
wrench sizeactuation
screw
stop screw
wrench
wrench sizestop
screw
2260223 HSK40EHCT025315 1/4 1.01 1.25 3.15 1.38 1.06 .39 1.03 170.135 5 MM 170.003 3 MM
2260224 HSK40EHCT038335 3/8 1.17 1.25 3.55 1.58 1.22 .39 1.17 170.135 5 MM 170.003 3 MM
2260225 HSK40EHCT050354 1/2 1.24 1.25 3.54 1.69 1.42 .39 1.23 170.135 5 MM 170.003 3 MM
2387471 HSK40EHCT062394 5/8 1.48 1.96 3.94 1.83 1.54 .39 1.87 170.135 5 MM 170.135 5 MM
2387472 HSK40EHCT075394 3/4 1.64 1.96 3.94 1.89 1.61 .39 1.98 170.135 5 MM 170.135 5 MM
IMPORTANT: Do not overtorque actuation screw. Use supplied wrench and tighten by hand until stop is felt.
Hydraulic chuck technical section, see page 805.
Supplied with stop screw and actuation wrench.
SEFAS chamfering rings cannot be used on the slim-style hydraulic chucks.
Reduction sleeves are available and must be ordered separately; see page 643.
HSK coolant unit and wrench are available and must be ordered separately; see page 763.
STRAIGHT SHANK QC / R8 SYSTEMS DV SYSTEM
CV SYSTEM
BT SYSTEM
INDEX TECHNICAL ACCESSORIES
COLLETS / SLEEVES
To place an order, contact Kennametal or your authorized Kennametal distributor, or visit www.kennametal.com. 429