ARMY *TM 9-6115-464-34 AIR FORCE TO-35C2-3 ... - Igor Chudov

More documents

Recommendations

Info

ARMY TM 9-6115-464-34AIR FORCE TO 35C2-3-445-2NAVY NAVFAC P-8-624-34Figure 3-22. Adjusting Fuel Injection Pump Roller-to-Roller Dimension(15) Carefully insert the transfer pump blades (71) and springs (70) taking care not to cock them. Rotatethe liner several times to check for freedom of movement. Return the liner to the correct position.(16) Install transfer pump seal (68).(17) Slip the head and rotor assembly, drive end up, into the holding fixture. Place the six governorweights (113) in their sockets with the slots facing the bore of the assembly. Place the thrust sleevewasher (115) against the thrust sleeve (114) so that the camfered edge faces the sleeve. Insert theforefinger into the bore of the sleeve and washer, holding them together, and insert them into theslots of the governor weights by tilting the weights slightly back. The two slots on the thrust sleeveflange should face up. Sight across the tops of the assembled weights to ascertain correctpositioning. One weight higher than others indicates incorrect assembly of the thrust washer.(18) Place the governor arm (86) in position with the fork for the governor linkage hook facing the endplate. Insert pivot shaft (85) with the knife edge facing the end plate and assemble the two seals (83and 84) and nuts (81 and 82). Tighten the nuts simultaneously to a torque of 20 to 25 inch-pounds.(19) install a new seal (122) on the hydraulic head. Rotate the cam ring so that the unthreaded hole is inline with the metering valve bore to insure proper positioning of the cam. Apply a light film of cleangrease around the inside edge of the housing (152).CAUTIONDo not use force. If the hydraulic head should cock during insertion, withdraw and startover. Failure to observe this caution could result in equipment damage.(20) Grasp the hydraulic head firmly in both hands and insert it into the housing with a slight rotarymotion.3-58
ARMY TM 9-6115 464 34AIR FORCE TO 35C2-3-445-2NAVY NAVFAC P-8-624-34NOTEMake sure that the assembly is wrung into position past the hydraulic head seal (122). Failure to do thismay result in leakage.(21) Rotate the hydraulic head until the head locking screw holes are aligned. Install head locking screws (136 and137) finger tight.(22) Invert the pump and holding fixture in the vise so that the bottom faces up.(23) Install seals (107) and head locating screw (106).(24) Install seals on piston plugs (96 and 108).(25) Install piston ring seal (110) and piston ring (109).(26) Install cam advance screw (105) using tool number 15500 and 15499 and torque to 400 inch- pounds. Install seal(104) and plug (103).(27) Using the piston ring installing tool (part number 16199), slide power piston plug (108) over piston (111).(28) Install spring (99), shim (100), piston (101), and slide washer (102) into plug (96). Install seal (98) onto plug (96).(29) Install plugs (96 and 108) with their assembled parts into the housing and torque to 215 to 265 inch-pounds.NOTEMake sure that the power piston plug is on the right side of the pump as viewed from the transfer pumpend.(30) Torque plug (103) to 75-100 inch-pounds(31) Torque head locating screw (106) to 300 inch-pounds(32) Torque head locking screws (136 and 137) to 180-220 inch-pounds(33) Invert the pump and holding fixture in the viseCAUTIONNever sand or polish off the special treatment on the valve. Failure to observe this caution could result inequipment damage.(34) Install the metering valve (93) and shims (95) into its bore. Depress and rotate the valve several times to insurefreedom of movement. If valve sticks, lap it carefully in dean oil.(35) Metering Valve Setup:(a)(b)(c)Install No.shim and No.16575 spacer on metering valve.Thread control rod guide No. 20223 into pump (finger tight).Check clearance between valve and control rod guide. Add shim No. 16576 through 16583 (as required) tocontrol clearance between 0.002 in. and 0.005 in. maximum.(36) Pull back on the governor linkage hook (50) stretching the spring just enough to Connect the hook correctly to thefork on the governor arm (86). Position the other end over the pin on the metering valve arm (91). Check allgovernor parts again for freedom of movement(37) With the end plate (66) removed, install the speed droop control rod though threaded hole from inside of pumphousing.Change 1 3-59
Page 1:
ARMY *TM 9-6115-464-34AIR FORCETO-3
Page 4 and 5:
ARMY TM 9-6115-464-34AIR FORCE 35C2
Page 7:
ARMY TM 9-6115 464 34AIR FORCE TO 3
Page 11 and 12:
ARMY TM 9-6115-464-34AIR FORCE TO 3
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Table 1-1. FITS AND TOLERANCES (CON
Page 33:
Table 1-1. FITS AND TOLERANCES (CON
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63: ARMY TM 9-6115-464-34AIR FORCE TO 3
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
ARMY TM 9-6115-464—34AIR FORCE 35
Page 270 and 271:
Page 272 and 273:
Page 274 and 275:
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Page 284 and 285:
Page 286 and 287:
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Page 300 and 301:
Page 302 and 303:
Page 304 and 305:
Page 306 and 307:
Page 308 and 309:
Page 310 and 311:
Page 312 and 313:
Page 314 and 315:
Page 316 and 317:
Page 318 and 319:
Page 320 and 321:
Page 322 and 323:
Page 324 and 325:
Page 326 and 327:
Page 328 and 329:
Page 330 and 331:
Page 332 and 333:
Page 334 and 335:
Page 336 and 337:
Page 338 and 339:
Page 340 and 341:
Page 342 and 343:
Page 344 and 345:
Page 346 and 347:
Page 348 and 349:
Page 350 and 351:
Page 352 and 353:
Page 354 and 355:
Page 356 and 357:
Page 358 and 359:
Page 360 and 361:
ARMY TM 9-6115-464—34AIR FORCE 35
Page 362 and 363:
Page 364 and 365:
(c)(d)(e)Pull all slack from the le
Page 366 and 367:
Page 368 and 369:
Page 370 and 371:
Page 372 and 373:
Page 374 and 375:
Page 376:
Page 379 and 380:
Page 381 and 382:
Page 383 and 384:
Page 385 and 386:
Page 387 and 388:
Page 389 and 390:
Page 391 and 392:
Page 393 and 394:
Page 395 and 396:
Page 397 and 398:
Page 399 and 400:
Page 401 and 402:
Page 404 and 405:
REPAIR INSTRUCTIONSARMY TM 9-6115-4
Page 406 and 407:
Page 408 and 409:
Page 410 and 411:
Page 412 and 413:
Page 414 and 415:
Page 416 and 417:
Page 418 and 419:
Page 420 and 421:
Page 422 and 423:
Page 424 and 425:
Page 426 and 427:
Page 428 and 429:
Page 430 and 431:
Page 432 and 433:
Page 434 and 435:
Page 436 and 437:
Page 438 and 439:
Page 440 and 441:
Page 442 and 443:
Page 444 and 445:
Page 446 and 447:
Page 448 and 449:
Page 450 and 451:
Page 452 and 453:
Page 454 and 455:
Page 456 and 457:
Page 458 and 459:
Page 460 and 461:
Page 462 and 463:
Page 464 and 465:
Page 466 and 467:
Page 468 and 469:
Page 470 and 471:
Page 472 and 473:
Page 474 and 475:
Page 476 and 477:
Page 478 and 479:
Page 480 and 481:
Page 482 and 483:
ARMY TM 9-6115 464 34AIR FORCE TO 3
Page 484 and 485:
Page 487 and 488:
Page 489 and 490:
Page 491:
ARMY TM 9-6115-464-34AIR FORCE TO-3
show all

ARMY *TM 9-6115-464-34 AIR FORCE TO-35C2-3 ... - Igor Chudov

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?