ARMY *TM 9-6115-464-34 AIR FORCE TO-35C2-3 ... - Igor Chudov

More documents

Recommendations

Info

ARMY TM 9-6115-464-34AIR FORCE 35C2-3-445-2NAVY NAVFAC P-8-624-34(e) Slowly raise output frequency of power source GI until test lamps transfer. Test lamps shall transferat 46 ± 1 Hz (375 Hz for 400 Hz units).(f) Adjust output voltage of power source G1 to 132 Vac. Check for test lamp transfer points. Transferpoints shall be within 1 Hz of those of steps (d) and (e).(g) Adjust output voltage of power source G1 to 108 Vac. Check for test lamp transfer points. Transferpoints shall be within 1 Hz of those of steps (d) and (e).(h) Open switch S1 and repeat steps (d) through (g). Transfer points shall be 55 ± 1 Hz and 58 ± 1 Hz(380 ± Hz and 385 ± 2 for 400 Hz units).(10) Test permissive paralleling relay as follows:(a)(b)(c)(d)(e)(f)(g)(h)(i)(j)(k)(l)Install permissive paralleling relay into test circuit shown in figure 3–126.Check that switch (S1) is open, then energize power sources G1 and G2.Adjust power source G1 to obtain reading of 15 Vac on voltmeter (M1).Adjust power source G1 to obtain reading of 50 Hz on frequency meter (M2).Close switch (S1) and observe test lamp (DS1) and (DS2). DS1 shall be dark and DS2 shall beilluminated.Slowly reduce the voltage of power source G1 until the relay drops out (DS1 extinguishes and DS2illuminates). Drop out shall occur at 8 ± 1 Vac.Slowly increase the voltage of power supply G1 until relay pickup occurs (DS1 illuminates and DS2extinguishes). Pick up shall occur at a voltage not greater than 1 Vac greater than drop out.Open switch (S1) and adjust frequency of power source G1 to 60 Hz.Repeat steps (e) through (g) above. Relay drop out and pick up shall occur at the same voltages.Open switch (S1) and adjust the frequency of power source G1 to 400 Hz.Repeat steps (e) through (g) above. Relay drop out and pick up shall occur at the same voltages.Increase the voltage of power source G1 to 300 Vac for 2 seconds. There shall be no damage as aresult of this test.(11) Replace relays which fail to perform as specified.(12) Test electronic components assembly as follows: (See schematic diagram in figure 3-127).(a) Check resistance across terminals 1 and 2 and across terminals 3 and 4. Resistance should be asspecified. If it is not, replace the defective resistors as necessary.(b) Test capacitor (terminals 5 and 6). Replace, if defective.(13) Replace defective components of electronic components assembly using figure 3-127 as a guide,and Appendix A references for detailed soldering and replacement procedures.(14) If the wiring harness has sustained damage and requires repair or rebuild, refer to figure 3-128(50/60 Hz) or 3-129 (400 Hz) for layout, identification and material requirements and Appendix A fordetailed soldering and replacement procedures.3-262
ARMY TM 9-6115-464-34AIR FORCE TO 35C2-3-445-2NAVY NAVFAC P-8-624-34Figure 3–1 26. Permissive Paralleling Relay Test Circuit(15) Check individual wires for continuity. Replace defective wires using wire conforming to MilitarySpecification MIL-W–5086, Type Il. Use figures 3-128 or 3-129 as a guide.d. Assembly..(1)Position chassis (33, figure 3-123) to install permissive paralleling relay (32) and screw & captivewasher assembly (31).(2)(3)(4)(5)(6)(7)(8)(9)(10)e. Installation.Install under frequency relay (30), screw & captive washer assembly (29).Install terminal jumper (28), terminal board assembly (27), screw (26), nut & captive washerassembly (25).Install electronic components assembly (24), screw & captive washer assembly (23) and nut (22).Install under voltage relay (21), screw& captive washer assembly (20).Install wiring harness (19), screw & captive washer assembly (18), and nut (17).Install screw (16), nut & captive washer assembly (15), flatwasher (14), nut & captive washerassembly (13).Install switch (12), positioning washer (11), tooth Iockwasher (10) and nut (9).Install rheostat (8), tooth Iockwasher (7), nut (6), and locknut (5).Install cover (4), screw & captive washer assembly (3).(1) Position precise relay assembly to install Iockwashers (2, figure 3-123) and screws (1).(2) Connect electrical connectors to precise relay assembly.3-263
Page 1:
ARMY *TM 9-6115-464-34AIR FORCETO-3
Page 4 and 5:
ARMY TM 9-6115-464-34AIR FORCE 35C2
Page 7:
ARMY TM 9-6115 464 34AIR FORCE TO 3
Page 11 and 12:
ARMY TM 9-6115-464-34AIR FORCE TO 3
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Table 1-1. FITS AND TOLERANCES (CON
Page 33:
Table 1-1. FITS AND TOLERANCES (CON
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267: ARMY TM 9-6115-464-34AIR FORCE 35C2
Page 268 and 269: ARMY TM 9-6115-464—34AIR FORCE 35
Page 360 and 361: ARMY TM 9-6115-464—34AIR FORCE 35
Page 364 and 365: (c)(d)(e)Pull all slack from the le
Page 366 and 367:
Page 368 and 369:
Page 370 and 371:
Page 372 and 373:
Page 374 and 375:
Page 376:
Page 379 and 380:
Page 381 and 382:
Page 383 and 384:
Page 385 and 386:
Page 387 and 388:
Page 389 and 390:
Page 391 and 392:
Page 393 and 394:
Page 395 and 396:
Page 397 and 398:
Page 399 and 400:
Page 401 and 402:
Page 404 and 405:
REPAIR INSTRUCTIONSARMY TM 9-6115-4
Page 406 and 407:
Page 408 and 409:
Page 410 and 411:
Page 412 and 413:
Page 414 and 415:
Page 416 and 417:
Page 418 and 419:
Page 420 and 421:
Page 422 and 423:
Page 424 and 425:
Page 426 and 427:
Page 428 and 429:
Page 430 and 431:
Page 432 and 433:
Page 434 and 435:
Page 436 and 437:
Page 438 and 439:
Page 440 and 441:
Page 442 and 443:
Page 444 and 445:
Page 446 and 447:
Page 448 and 449:
Page 450 and 451:
Page 452 and 453:
Page 454 and 455:
Page 456 and 457:
Page 458 and 459:
Page 460 and 461:
Page 462 and 463:
Page 464 and 465:
Page 466 and 467:
Page 468 and 469:
Page 470 and 471:
Page 472 and 473:
Page 474 and 475:
Page 476 and 477:
Page 478 and 479:
Page 480 and 481:
Page 482 and 483:
ARMY TM 9-6115 464 34AIR FORCE TO 3
Page 484 and 485:
Page 487 and 488:
Page 489 and 490:
Page 491:
ARMY TM 9-6115-464-34AIR FORCE TO-3
show all

ARMY *TM 9-6115-464-34 AIR FORCE TO-35C2-3 ... - Igor Chudov

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?