ARMY *TM 9-6115-464-34 AIR FORCE TO-35C2-3 ... - Igor Chudov

More documents

Recommendations

Info

ARMY TM 9-6115-464-34AIR FORCE TO 35C2-3-445-2NAVY NAVFAC P-8-624-345-3. HEATER CONTROL ASSEMBLY.a. Removal. Refer to the Operator and Unit Maintenance Manual for heater control assembly removalinstructions.b Disassembly.(1) Tag all electrical leads before disconnecting.(2) Remove screws (1, figure 5-1), and remove panel assembly (9), from housing (21).(3) Remove nut (2), tooth lockwasher (3), on-off switch (15), and key washer (11).(4) Remove nut (4), Iockwasher (5), and circuit breaker (16).(5) Remove lens (6), lamp (7), nut (8), lockwasher (10) and indicator light base (17) from panel (9).(6) Remove screw (13) from housing (14).(7) Remove nut (18), screw (19), and connector, from housing (21).c. Cleaning, Inspection, and Repair.WARNINGCompressed air used for cleaning and drying purposes can create airborne particlesthat may enter the eyes. Pressure shall not exceed 30 psig and use only with adequatechip guards and chipping goggles. Failure to observe this warning could result inserious personal injury or death.WARNINGSolvent, Dry Cleaning P–D-680, Type II is flammable and moderately toxic to skin,eyes and respiratory tract. Eye and skin protection required. Good general ventilationis normally adequate. Failure to observe this warning could result in serious personalinjury or death.(1)(2)(3)(4)(5)(6)(7)(8)(9)(10)Clean all electrical parts with filtered compressed air and a soft bristle brush. If necessary, cakeddeposits may be removed with a clean, lint-free cloth moistened with solvent P-D-680 Type Il.Clean all non-electrical parts with a clean, lint–free cloth moistened with dry cleaning solvent(Federal Specification P-D-680).Inspect ON-OFF switch for cracked casing, corrosion, and burns or other evidence of shorting.Place switch in the ON position and check for continuity, using an ohmmeter. Ohmmeter shallindicate continuity. Check for open circuit with switch in the OFF position. Ohmmeter shall indicateopen circuit.Inspect circuit breaker for cracked casing, corrosion, and burns or other indications of shorting.Using an ohmmeter, check for open circuit across circuit breaker terminals. Ohmmeter shall indicateopen circuit. Depress circuit breaker button. Ohmmeter shall indicate continuity.Inspect indicator light lens for cracked or broken glass, corrosion, and other damage.Inspect lamp for cracked or broken glass, burned out filament and corrosion.Check indicator light base for cracks, corrosion, and burns.Inspect wiring harness for damaged connectors, wires, and terminals. Check individual wires forcontinuity using figure 5-2 as a guide.5-5
ARMY TM 9-6116-464-34AIR FORCE TO 35C2-3-445-2NAVY NAVFAC P-8-624-34(11) Replace damaged connectors and terminals by unsoldering and removing electrical leads. Installreplacement part, make mechanical connection and solder in accordance with establishedprocedure.(12) Replace defective wires using wire conforming to Military Specification MIL-W-5086, Type Il.(13) Inspect housing for cracks, warping, and corrosion.(14) Inspect all threads for crossing, stripping, and other damage.(15) Replace all damaged or defective parts.d. Assembly.(1) Install connector (20, figure 5-1), screws (19), nuts (18) on housing (21).(2) Install screws (13) in housing (14).(3) Install indicator light base (17), tooth lockwasher (10), nut (8), lamp (7), and lens (6) on panelassembly (9).(4) Install circuit breaker (16), Iockwasher (5) and nut (4).(5) Install key washer (11), on-off switch (15), tooth Iockwasher (3) and nut (2).(6) Position panel assembly (9), and install screws (1).e. Installation. Refer to the Operator and Unit Maintenance Manual for fuel burning winterization heatercontrol assembly installation instructions.5-6
Page 1:
ARMY *TM 9-6115-464-34AIR FORCETO-3
Page 4 and 5:
ARMY TM 9-6115-464-34AIR FORCE 35C2
Page 7:
ARMY TM 9-6115 464 34AIR FORCE TO 3
Page 11 and 12:
ARMY TM 9-6115-464-34AIR FORCE TO 3
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Table 1-1. FITS AND TOLERANCES (CON
Page 33:
Table 1-1. FITS AND TOLERANCES (CON
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
ARMY TM 9-6115-464—34AIR FORCE 35
Page 270 and 271:
Page 272 and 273:
Page 274 and 275:
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Page 284 and 285:
Page 286 and 287:
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Page 300 and 301:
Page 302 and 303:
Page 304 and 305:
Page 306 and 307:
Page 308 and 309:
Page 310 and 311:
Page 312 and 313:
Page 314 and 315:
Page 316 and 317:
Page 318 and 319:
Page 320 and 321:
Page 322 and 323:
Page 324 and 325:
Page 326 and 327:
Page 328 and 329:
Page 330 and 331:
Page 332 and 333:
Page 334 and 335:
Page 336 and 337:
Page 338 and 339:
Page 340 and 341:
Page 342 and 343:
Page 344 and 345:
Page 346 and 347:
Page 348 and 349:
Page 350 and 351:
Page 352 and 353:
Page 354 and 355:
Page 356 and 357:
Page 358 and 359: ARMY TM 9-6115-464-34AIR FORCE 35C2
Page 360 and 361: ARMY TM 9-6115-464—34AIR FORCE 35
Page 362 and 363: ARMY TM 9-6115-464-34AIR FORCE 35C2
Page 364 and 365: (c)(d)(e)Pull all slack from the le
Page 366 and 367: ARMY TM 9-6115-464-34AIR FORCE TO 3
Page 376: ARMY TM 9-6115-464-34AIR FORCE TO 3
Page 404 and 405: REPAIR INSTRUCTIONSARMY TM 9-6115-4
Page 458 and 459:
Page 460 and 461:
Page 462 and 463:
Page 464 and 465:
Page 466 and 467:
Page 468 and 469:
Page 470 and 471:
Page 472 and 473:
Page 474 and 475:
Page 476 and 477:
Page 478 and 479:
Page 480 and 481:
Page 482 and 483:
ARMY TM 9-6115 464 34AIR FORCE TO 3
Page 484 and 485:
Page 487 and 488:
Page 489 and 490:
Page 491:
ARMY TM 9-6115-464-34AIR FORCE TO-3
show all

ARMY *TM 9-6115-464-34 AIR FORCE TO-35C2-3 ... - Igor Chudov

Create successful ePaper yourself

Delete template?

Save as template?