general information - Martin Nez

2-12 PERIODIC MAINTENANCE(EXHAUST SIDE)TAPPET SHIM SELECTION TABLE [EXHAUST]TAPPET SHIM NO. (12892-05C00-XXX)TAPPET SHIM SET (12800-05830)SUFFIXNO.120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220MEASUREDVALVECLEARANCE(mm)PRESENTSHIM SIZE(mm) 1.20 1.25 1.30 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.200.05 – 0.090.10 – 0.140.15 – 0.190.20 – 0.300.31 – 0.350.36 – 0.400.41 – 0.450.46 – 0.500.51 – 0.550.56 – 0.600.61 – 0.650.66 – 0.700.71 – 0.750.76 – 0.800.81 – 0.850.86 – 0.900.91 – 0.950.96 – 1.001.01 – 1.051.06 – 1.101.11 – 1.151.20 1.25 1.30 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.051.20 1.25 1.30 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10SPECIFIED CLEARANCE/NO ADJUSTMENT REQUIRED1.30 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20 2.201.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.201.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.201.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.201.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.201.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.201.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.201.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.201.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.201.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.201.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.201.85 1.90 1.95 2.00 2.05 2.10 2.15 2.201.90 1.95 2.00 2.05 2.10 2.15 2.201.95 2.00 2.05 2.10 2.15 2.202.00 2.05 2.10 2.15 2.202.05 2.10 2.15 2.202.10 2.15 2.201.16 – 1.202.15 2.201.21 – 1.25 2.201.20 1.25 1.30 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15HOW TO USE THIS CHART:I. Measure valve clearance. “ENGINE IS COLD”II. Measure present shim size.III. Match clearance in vertical column with present shim size in horizontalcolumn.EXAMPLEValve clearance is 0.33 mmPresent shim size 1.70 mmShim size to be used 1.80 mm