Process Unit 73 LF - Knick

More documents

Recommendations

Info

Process Unit 73 LF How to access the Diagnostics menu Pressing opens the Diagnostics menu. Pressing or exits the Diagnostics menu. Message List Press or to access the ”Message List”. All currently active failure and warning messages are displayed. For description of messages, refer to chapter 11. Press to return to the Diagnostics menu. Measurement Data Press and to access the ”Measurement Data”. The point of measurement (to DIN 19227/ ISO 3511) is displayed. Below, you can read the cell constant and which limit values are set. If the unit is equipped with option 352 (probe rinsing), you can see if probe rinsing is activated. If the unit is equipped with option 353 (digital controller) or option 483 (analog controller) and the controller is activated, the controller setpoint is displayed. With activated digital controller, the limit values are not monitored. Press to return to the Diagnostics menu. 3–2 Diagnostics
How to enter the point of measurement On the Administrator level you select menu item ”Point of Measurement”. You can select . 0...9 A...Z – + / using the scrolling keys. Enter the point of measurement using scrolling and cursor keys (see page 2–5) and confirm your entry with . Logbook You can only make use of the logbook if your unit is equipped with option 354. Without this option, the menu reads “Logbook (Optional)”, and this item cannot be selected. What is the logbook? The logbook contains the last 200 events with date and time and displays them. Error messages occurring during parameter setting, calibration or maintenance are not recorded. The following events are recorded: instrument in measuring mode instrument turned on/off : start of warning and failure messages : end of warning and failure messages probe rinsing activated calibration messages, cell constant parameter setting, calibration, maintenance or diagnostics activated entry of wrong passcodes What you can do with the logbook The logbook entries can be used for quality management documentation to ISO 9000 and GLP/ GMP. Logbook entries cannot be edited! If the instrument is equipped with option 351 (remote interface) (refer to page 9–49), the logbook contents can be read out and automatically documented. Diagnostics 3–3
Page 1 and 2: Instruction Manual Process Unit 73
Page 3 and 4: Changes for Software Release 6 Proc
Page 5 and 6: Safety Information Be sure to read
Page 7 and 8: Information on Electromagnetic Comp
Page 9 and 10: The representation of a menu in thi
Page 11 and 12: Contents Safety Information . . . .
Page 13 and 14: 9 Capabilities of the Process Unit
Page 15 and 16: 1 Overview of the Process Unit 73 L
Page 17 and 18: vanic isolation optional) allows li
Page 19 and 20: 2 Operating the Process Unit 73 LF
Page 21 and 22: Control Elements Pressing menu key
Page 23 and 24: How to select a menu item Press scr
Page 25 and 26: How to keep the old setting Pressin
Page 27: 3 Diagnostics Menu What you can do
Page 31 and 32: Device Diagnostics What you can do
Page 33 and 34: 4 Maintenance Menu What you can do
Page 35 and 36: Resistance Measurement Press and
Page 37 and 38: Temperature Probe Adjustment This f
Page 39 and 40: 5 Viewing Level What you can do on
Page 41 and 42: 6 Calibration Why do you have to ca
Page 43 and 44: How to select a calibration sequenc
Page 45 and 46: Automatic Calibration with Standard
Page 47 and 48: Calibration by Manual Entry of Cond
Page 49 and 50: Calibration by Entry of Premeasured
Page 51 and 52: With TC correction T ref = 25 °C W
Page 53 and 54: 7 Operator Level What you can do on
Page 55 and 56: 8 Administrator Level Before commis
Page 57 and 58: An Example You want to change the s
Page 59 and 60: How to set the administrator passco
Page 61 and 62: 9 Capabilities of the Process Unit
Page 63 and 64: Pt 100/ Pt 1000/ Ni 100 Process Uni
Page 65 and 66: wt pk bn gy bu gn rd yw Shi
Page 67 and 68: Conductivity Measurement using ZU 0
Page 69 and 70: Sensor cable Terminal box ZU 0307 E
Page 71 and 72: Sensor cable Terminal box ZU 0307 g
Page 73 and 74: Calibration Solution for Automatic
Page 75 and 76: Manual Temperature Compensation Man
Page 77 and 78: How to define temperature compensat
Page 79 and 80:
Trilinear Output Curve output curre
Page 81 and 82:
2nd Current Output If your unit is
Page 83 and 84:
100 Trilinear (Bilinear) Curve (fal
Page 85 and 86:
How to set the parameters for conce
Page 87 and 88:
Complete Installation using all Fun
Page 89 and 90:
NAMUR Contacts The three NAMUR cont
Page 91 and 92:
During calibration the limit contac
Page 93 and 94:
In measuring mode the present value
Page 95 and 96:
Output 2 can be used to control val
Page 97 and 98:
The information text shows the cont
Page 99 and 100:
ÍÍÍÍÍÍÍÍÍÍÍÍ ÍÍÍÍÍ
Page 101 and 102:
Error Messages for Controller Setti
Page 103 and 104:
How to set the current input parame
Page 105 and 106:
Cleaning: The contact ”cleaning
Page 107 and 108:
How to set the rinsing cycle parame
Page 109 and 110:
Remote Interface Operation You can
Page 111 and 112:
How to set the interface parameters
Page 113 and 114:
10 Information on Mounting and Inst
Page 115 and 116:
front removable for instrument inst
Page 117 and 118:
Installation Installation of the Pr
Page 119:
Maintenance and Cleaning The Proces
Page 122 and 123:
Process Unit 73 LF Error Message (D
Page 124 and 125:
Process Unit 73 LF According to Int
Page 126 and 127:
Process Unit 73 LF 11-6 Error Messa
Page 128 and 129:
Process Unit 73 LF Output Current 1
Page 130 and 131:
Process Unit 73 LF Transmission beh
Page 132 and 133:
Process Unit 73 LF STATUS Commands:
Page 134 and 135:
Process Unit 73 LF Device Diagnosti
Page 136 and 137:
Process Unit 73 LF Clock RPRTM WPRT
Page 138 and 139:
Process Unit 73 LF WPDISLAI1 Displa
Page 140 and 141:
Process Unit 73 LF RPTOMA WPTOMA0 W
Page 142 and 143:
Process Unit 73 LF Output Current 1
Page 144 and 145:
Process Unit 73 LF Output 2/Control
Page 146 and 147:
Process Unit 73 LF Limit Contacts/C
Page 148 and 149:
Process Unit 73 LF RPCIBV WPCIBVp R
Page 150 and 151:
Process Unit 73 LF Current Input RP
Page 152 and 153:
Process Unit 73 LF Automatic Device
Page 154 and 155:
Process Unit 73 LF Digital Controll
Page 156 and 157:
Process Unit 73 LF Interface Bus Pr
Page 158 and 159:
Process Unit 73 LF 4th Field: CRC16
Page 160 and 161:
Process Unit 73 LF Interface Bus Pr
Page 162 and 163:
Process Unit 73 LF Mounting Accesso
Page 164 and 165:
Process Unit 73 LF Display Display
Page 166 and 167:
Process Unit 73 LF Cells Model SE 6
Page 168 and 169:
Process Unit 73 LF Model ZU 0071*)
Page 170 and 171:
Process Unit 73 LF cable length app
Page 172 and 173:
Process Unit 73 LF 1 Observe instal
Page 174 and 175:
Process Unit 73 LF connector plug W
Page 176 and 177:
Process Unit 73 LF [mS/cm] 1,200 H
Page 178 and 179:
Process Unit 73 LF 700 [mS/cm] Sal
Page 180 and 181:
Process Unit 73 LF Sodium Chloride
Page 182 and 183:
Process Unit 73 LF EPROM Replacemen
Page 184 and 185:
Process Unit 73 LF 16-4 Appendix
Page 186 and 187:
Process Unit 73 LF conductance cond
Page 188 and 189:
Process Unit 73 LF Parameter Settin
Page 190 and 191:
Process Unit 73 LF cell, SE 603 app
Page 192 and 193:
Process Unit 73 LF limit contacts/c
Page 194:
Process Unit 73 LF viewing angle ad
show all

Process Unit 73 LF - Knick

Create successful ePaper yourself

Delete template?

Save as template?