MMC User Manual - AMS Neve

-40
-40
0
-10
-20
-30
-40
-50
0
-10
-20
-30
-40
-40
-40
-40
-40
-40
-40
0
-10
-20
-30
-40
-50
0
-10
-20
-30
-40
-40
-40
-40
-40
-40
-40
0
-10
-20
-30
-40
-50
0
-10
-20
-30
-40
-40
-40
0
-10
-20
-30
-40
-50
0
-10
-20
-30
-40
0
-10
-20
-30
-40
-50
0
-10
-20
-30
-40
0
-10
-20
-30
-40
-50
0
-10
-20
-30
-40
Metering
Meter Bridge
Meter Bridge
The Logic MMC Meter Bridge consists of a Main Meter Section, and Strip Meter Sections on either side.
The Main Meter Section consists of 8 stereo Aux meters and 8 stereo Aux/Group meters, a master stereo
bargraph meter with an associated phase meter and two dynamic VU meters. There are keys for selecting the
signals to be metered and an LED panel for indicating solo, power and overload status.
0
0
0
0
0
0
0
0
0
-10
-20
-60
-10
-20
-60
-10
-20
-60
-10
-20
-60
-10
-20
-60
-10
-20
-60
-10
-20
-60
-10
-20
-60
/O
-5
-10
-20
-20
R22AF
-10
20
VU
-7
-5
40
60
-3
-2
80
-1
100
0
+1
VU
+2
+ 3
-20
R22AF
-10
20
VU
-7
-5
40
60
-3
-2
80
-1
100
0
+1
VU
+2
+ 3
AUX1
AUX2
AUX3
AUX4
AUX5
AUX6
AUX7
AUX8
-30
LEFT
RIGHT
0
0
0
0
0
0
0
0
-40
-10
-10
-10
-10
-10
-10
-10
-10
-60
ASSIGN
-20
-20
-20
-20
-20
-20
-20
-20
ASSIGN
POWER
SOLO FAIL O/LOAD
STRIP METERS
BUS/
TAPE
OPER
LEVEL
FOLL
FDR
-60
GP1
AUX9
-60
GP2
AUX10
-60
-60
GP3 GP4
AUX11 AUX12
-60
GP5
AUX13
-60
GP6
AUX14
-60
-60
GP7 GP8
AUX15 AUX16
GP/
AUX
AUX/
MON
DYN
SEL FOLL
S.MTR KNOB
The master stereo bargraph meter and associated phase meter follow the source selected for the Control Room
monitors. The alpha display below the meters shows the currently selected Control Room source (see the
Monitoring chapter).
The Strip Meters are stereo bargraph meters which can be selected between Input, Bus and Tape metering.
BUS
BUS
BUS
BUS
BUS
BUS
DYN
DYN
DYN
DYN
DYN
DYN
0
0
0
0
0
0
-10
-10
-10
-10
-10
-10
-20
-20
-20
-20
-20
-20
-30
-30
-30
-30
-30
-30
A
MON
B
-40
-50
-60
A
MON
B
-40
-50
-60
A
MON
B
-40
-50
-60
A
MON
B
-40
-50
-60
A
MON
B
-40
-50
-60
A
MON
B
-40
-50
-60
0
0
0
0
0
0
-10
-10
-10
-10
-10
-10
-20
-20
-20
-20
-20
-20
-30
-40
-60
-30
-40
-60
-30
-40
-60
-30
-40
-60
-30
-40
-60
-30
-40
-60
HID
HID
HID
HID
HID
HID
1 2 3 4 5 6
Mono signals will be displayed on the left leg of the bargraph meters.
Aux/Group Metering
Sixteen stereo bargraph meters on the Main Meter Section of the Meter Bridge are used for Aux metering. Eight
of these may be re-assigned for Group metering.
To re-assign Aux meters 9 to 16 to meter Groups press the GP/AUX key on the Main Meter Section.
The integral LED will illuminate and the GP1 to GP8 LEDs under the Group/Aux meters will illuminate.
Aux/Mon Metering
The metering for auxes 1-8 can be swapped to show the Film outputs. Pressing the AUX/MON key switches
between auxes 1-8 and the Films.
Assigning the VU Meters
SEL6 is used for sending a signal to the VU Meters. This allows the SELECT Panel to be used for signal source
selection.
To select the signal to be metered by the Meter Bridge VU Meters press and hold the ASSIGN key below the
meters.
The SELECT Panel is now used for selection of the required signal.
Press the MAIN, GRP, AUX or EXT key on the SELECT Panel.
The integral LED will illuminate red.
Issue 4 Page 11:2