REFERENCE MANUAL - FTP Directory Listing - Trimble

More documents

Recommendations

Info

COPERNICUS <strong>REFERENCE</strong> BOARD 10 Reference Board Jumper Table Table 10.2 Copernicus Reference Board Jumper Table Reference Designator Name Description J1 RF Input MCX Jack (Female Connector)50 Ohms unbalanced J4 XRESET Normal Operation: Jumper in place (connects XRESET to VCC) Reset Operation: Removing the Jumper and asserting pin 2 of J4 low for greater than 100 usec resets the unit. *Switch SW1 can also reset the unit. Please see below. SW1 Reset Switch Press the button resets the unit. J5 VCC Normal Operation: Jumper in place (Applies VCC to unit) Test Mode: Jumper may be removed and ampere meter may be inserted for current measurement. J6 Vback Normal Operation: Jumper in place.(Applies VBack to unit). The user can use VCC as the STANDBY Supply. J7 8-Pin Header See Table 10 for Reference Board pin Description. J8 PPS Normal Operation: Jumper in place.(It outputs PPS at pin 9 of both DB9 connectors of the Starter Kit through J7 pin 6 of the Reference Board). J9-J21 Reserved Reserved J25 Reserved Reserved Normal Operation: No Jumper (Run Mode). J27 Reserved Reserved J28 XSTANDBY Normal Operation: Jumper between pins 1 and 2 of the jumper J28 (Run Mode). * Standby Mode: Jumper between pins 2 and 3 of J28. *For external control, Jumper may be removed and pin 2 of the jumper can be externally controlled, e.g. via a host processor. J22-24 Spare Spare driver transistor J26 Antenna Power Normal Operation: Jumper in place.(Active antenna powered from VCC).If a separate power supply is desired for active antenna, jumper may be removed and an external antenna power can be applied to pin 2 of J26. * * See Copernicus Reference Board Schematics in this chapter. Note – See Table 3.1 for pin numbers. indicates pin 1. Copernicus GPS Receiver 103
10 COPERNICUS <strong>REFERENCE</strong> BOARD Reference Board Component Locations Drawing Figure 10.4 Copernicus Reference Board, Top Side Figure 10.5 Copernicus Reference Board Schematic, Bottom Side 104 Copernicus GPS Receiver
Page 1 and 2:
REFERENCE MANUAL Copernicus GPS Re
Page 3 and 4:
Corporate Office Trimble Navigation
Page 6 and 7:
Table of Contents Table of Contents
Page 8 and 9:
Table of Contents 7 MECHANICAL SPEC
Page 10 and 11:
Table of Contents Command Packet 0x
Page 12 and 13:
Table of Contents X1 Extended Statu
Page 14 and 15:
CHAPTER 1 STARTER KIT 1 In this cha
Page 16 and 17:
STARTER KIT 1 Starter Kit The Coper
Page 18 and 19:
STARTER KIT 1 Figure 1.3 USB Cable
Page 20 and 21:
STARTER KIT 1 Interface Connections
Page 22 and 23:
STARTER KIT 1 Removing the Referenc
Page 24 and 25:
STARTER KIT 1 Quick Start Guide 1.
Page 26 and 27:
STARTER KIT 1 Trimble GPS Monitor T
Page 28 and 29:
STARTER KIT 1 4. Click the Device M
Page 30 and 31:
STARTER KIT 1 Connect to the GPS Re
Page 32 and 33:
STARTER KIT 1 Configure GPS Ports 1
Page 34 and 35:
STARTER KIT 1 Configure PPS Output
Page 36 and 37:
STARTER KIT 1 Creating a Log Follow
Page 38 and 39:
STARTER KIT 1 3. Select one of the
Page 40 and 41:
CHAPTER 2 PRODUCT DESCRIPTION 2 In
Page 42 and 43:
PRODUCT DESCRIPTION 2 Block Diagram
Page 44 and 45:
PRODUCT DESCRIPTION 2 Electrical El
Page 46 and 47:
PRODUCT DESCRIPTION 2 Absolute Mini
Page 48 and 49:
PRODUCT DESCRIPTION 2 Power Consump
Page 50 and 51:
CHAPTER 3 INTERFACE CHARACTERISTICS
Page 52 and 53:
INTERFACE CHARACTERISTICS 3 Pin Des
Page 54 and 55:
INTERFACE CHARACTERISTICS 3 Table 3
Page 56 and 57:
INTERFACE CHARACTERISTICS 3 Serial
Page 58 and 59:
INTERFACE CHARACTERISTICS 3 Acquiri
Page 60 and 61:
INTERFACE CHARACTERISTICS 3 Enablin
Page 62 and 63: CHAPTER 4 OPERATING MODES 4 In this
Page 64 and 65: OPERATING MODES 4 Changing the Run/
Page 66 and 67: OPERATING MODES 4 Serial Port Activ
Page 68 and 69: OPERATING MODES 4 Saving Almanac, E
Page 70 and 71: CHAPTER 5 APPLICATION CIRCUITS 5 In
Page 72 and 73: APPLICATION CIRCUITS 5 Figure 5.2 P
Page 74 and 75: APPLICATION CIRCUITS 5 • Antenna
Page 76 and 77: APPLICATION CIRCUITS 5 Following is
Page 78 and 79: CHAPTER 6 RF LAYOUT CONSIDERATIONS
Page 80 and 81: RF LAYOUT CONSIDERATIONS 6 In the p
Page 82 and 83: RF LAYOUT CONSIDERATIONS 6 PCB Cons
Page 84 and 85: RF LAYOUT CONSIDERATIONS 6 Striplin
Page 86 and 87: CHAPTER 7 MECHANICAL SPECIFICATIONS
Page 88 and 89: MECHANICAL SPECIFICATIONS 7 Solderi
Page 90 and 91: MECHANICAL SPECIFICATIONS 7 Paste M
Page 92 and 93: CHAPTER 8 PACKAGING 8 In this chapt
Page 94 and 95: PACKAGING 8 Reel The 13-inch reel t
Page 96 and 97: CHAPTER 9 SHIPPING and HANDLING 9 I
Page 98 and 99: SHIPPING and HANDLING 9 Moisture Pr
Page 100 and 101: SHIPPING and HANDLING 9 Recommended
Page 102 and 103: SHIPPING and HANDLING 9 Grounding t
Page 104 and 105: CHAPTER 10 COPERNICUS REFERENCE BOA
Page 106 and 107: COPERNICUS REFERENCE BOARD 10 IMAGE
Page 108 and 109: COPERNICUS REFERENCE BOARD 10 Refer
Page 110 and 111: COPERNICUS REFERENCE BOARD 10 Refer
Page 114 and 115: CHAPTER 11 FIRMWARE UPGRADE 11 In t
Page 116 and 117: FIRMWARE UPGRADE 11 Firmware Binary
Page 118 and 119: FIRMWARE UPGRADE 11 Pseudo-Code Exp
Page 120 and 121: FIRMWARE UPGRADE 11 Error Recovery
Page 122 and 123: FIRMWARE UPGRADE 11 Packet ID - 0x8
Page 124 and 125: FIRMWARE UPGRADE 11 Packet ID - 0x8
Page 126 and 127: FIRMWARE UPGRADE 11 Loading Firmwar
Page 128 and 129: APPENDIX A TRIMBLE STANDARD INTERFA
Page 130 and 131: TRIMBLE STANDARD INTERFACE PROTOCOL
Page 162 and 163:
TRIMBLE STANDARD INTERFACE PROTOCOL
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
APPENDIX B TRIMBLE ASCII INTERFACE
Page 196 and 197:
TRIMBLE ASCII INTERFACE PROTOCOL (T
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
APPENDIX C NMEA 0183 C In this appe
Page 222 and 223:
NMEA 0183 C The NMEA 0183 Communica
Page 224 and 225:
NMEA 0183 C Note - Spaces are only
Page 226 and 227:
NMEA 0183 C General NMEA Parser Req
Page 228 and 229:
NMEA 0183 C Table C.4 Copernicus GP
Page 230 and 231:
NMEA 0183 C GLL - Geographic Positi
Page 232 and 233:
NMEA 0183 C RMC - Recommended Minim
Page 234 and 235:
NMEA 0183 C AH - Almanac Health Thi
Page 236 and 237:
NMEA 0183 C AS - Almanac Status Thi
Page 238 and 239:
NMEA 0183 C EP - Ephemeris This sen
Page 240 and 241:
NMEA 0183 C IO Ionosphere This sent
Page 242 and 243:
NMEA 0183 C PS - PPS Configuration
Page 244 and 245:
NMEA 0183 C RT - Reset This sentenc
Page 246 and 247:
NMEA 0183 C Table C.29 SG - Set Bit
Page 248 and 249:
NMEA 0183 C TF - Receiver Status an
Page 250 and 251:
NMEA 0183 C VR - Version This sente
show all

REFERENCE MANUAL - FTP Directory Listing - Trimble

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?