REFERENCE MANUAL - FTP Directory Listing - Trimble

More documents

Recommendations

Info

TRIMBLE ASCII INTERFACE PROTOCOL (TAIP) B The Set Qualifier The set (S) qualifier enables the user equipment to initialize/set-up various types of data in the GPS unit. The format is: >SAA[{B}][;ID=CCCC][;*DD]< where AA is the two character message identifier and {B} specifies the data string within the message. For the format of {B}, please refer to the message definitions in the previous section. Note that all the messages have very specific formats and are length dependent. Messages normally supported by the set qualifier are AL, AP, CP, DC, DD, ID, IP, LN, PT, PV, and RM. The set qualifier may be used with the AL, CP, LN, or PV message to set more precise initial position data into the GPS receiver than can be set with the IP message. Note – The Lassen PT GPS does not support the AP TAIP message. Sample Communication Session The following is a sample communication session to illustrate how message qualifiers are used. Query the receiver for version number for the TAIP firmware: >QVR< The receiver responds with a message in the following form: >RVR CT COPERNICUS APP; VERSION 01.05 (05/23/06);*6E< Note – The receiver identified its product name, firmware version number, core signal processing version number, and release dates, then included the checksum for the message (the default for the CS Flag is TRUE). Also notice that the receiver did respond to our query even though we did not send a checksum. Query the receiver for its ID number: >QID< The receiver will respond (assuming factory default settings): >RID0000;*70< Set the ID to match the number for a vehicle in your fleet and then tell the receiver to include the Vehicle ID in its responses: >SID1234< >SRM;ID_FLAG=T< The Lassen iQ receiver receiver is set by default to report the PV message once every 5 seconds. To schedule the PV message from vehicle 1234 to respond once every 10 seconds, starting at 5 seconds after the top of the hour, use the following command: >FPV00100005;ID=1234< Copernicus GPS Receiver 209
B TRIMBLE ASCII INTERFACE PROTOCOL (TAIP) The receiver will check the ID included in the message for a match with its own and then reschedule the PV message. At the next scheduled time, the receiver will respond with: >RPV15714+3739438-1220384601512612;ID=1234;*7F< Note – The Lassen PT GPS does not support the AP TAIP message. The time given in the message is the time of the last GPS fix (04:21:54 GPS), not necessarily the time of the message response. If the time of last fix is 10 or more seconds old, the age flag will be set to 1. 210 Copernicus GPS Receiver
Page 1 and 2:
REFERENCE MANUAL Copernicus GPS Re
Page 3 and 4:
Corporate Office Trimble Navigation
Page 6 and 7:
Table of Contents Table of Contents
Page 8 and 9:
Table of Contents 7 MECHANICAL SPEC
Page 10 and 11:
Table of Contents Command Packet 0x
Page 12 and 13:
Table of Contents X1 Extended Statu
Page 14 and 15:
CHAPTER 1 STARTER KIT 1 In this cha
Page 16 and 17:
STARTER KIT 1 Starter Kit The Coper
Page 18 and 19:
STARTER KIT 1 Figure 1.3 USB Cable
Page 20 and 21:
STARTER KIT 1 Interface Connections
Page 22 and 23:
STARTER KIT 1 Removing the Referenc
Page 24 and 25:
STARTER KIT 1 Quick Start Guide 1.
Page 26 and 27:
STARTER KIT 1 Trimble GPS Monitor T
Page 28 and 29:
STARTER KIT 1 4. Click the Device M
Page 30 and 31:
STARTER KIT 1 Connect to the GPS Re
Page 32 and 33:
STARTER KIT 1 Configure GPS Ports 1
Page 34 and 35:
STARTER KIT 1 Configure PPS Output
Page 36 and 37:
STARTER KIT 1 Creating a Log Follow
Page 38 and 39:
STARTER KIT 1 3. Select one of the
Page 40 and 41:
CHAPTER 2 PRODUCT DESCRIPTION 2 In
Page 42 and 43:
PRODUCT DESCRIPTION 2 Block Diagram
Page 44 and 45:
PRODUCT DESCRIPTION 2 Electrical El
Page 46 and 47:
PRODUCT DESCRIPTION 2 Absolute Mini
Page 48 and 49:
PRODUCT DESCRIPTION 2 Power Consump
Page 50 and 51:
CHAPTER 3 INTERFACE CHARACTERISTICS
Page 52 and 53:
INTERFACE CHARACTERISTICS 3 Pin Des
Page 54 and 55:
INTERFACE CHARACTERISTICS 3 Table 3
Page 56 and 57:
INTERFACE CHARACTERISTICS 3 Serial
Page 58 and 59:
INTERFACE CHARACTERISTICS 3 Acquiri
Page 60 and 61:
INTERFACE CHARACTERISTICS 3 Enablin
Page 62 and 63:
CHAPTER 4 OPERATING MODES 4 In this
Page 64 and 65:
OPERATING MODES 4 Changing the Run/
Page 66 and 67:
OPERATING MODES 4 Serial Port Activ
Page 68 and 69:
OPERATING MODES 4 Saving Almanac, E
Page 70 and 71:
CHAPTER 5 APPLICATION CIRCUITS 5 In
Page 72 and 73:
APPLICATION CIRCUITS 5 Figure 5.2 P
Page 74 and 75:
APPLICATION CIRCUITS 5 • Antenna
Page 76 and 77:
APPLICATION CIRCUITS 5 Following is
Page 78 and 79:
CHAPTER 6 RF LAYOUT CONSIDERATIONS
Page 80 and 81:
RF LAYOUT CONSIDERATIONS 6 In the p
Page 82 and 83:
RF LAYOUT CONSIDERATIONS 6 PCB Cons
Page 84 and 85:
RF LAYOUT CONSIDERATIONS 6 Striplin
Page 86 and 87:
CHAPTER 7 MECHANICAL SPECIFICATIONS
Page 88 and 89:
MECHANICAL SPECIFICATIONS 7 Solderi
Page 90 and 91:
MECHANICAL SPECIFICATIONS 7 Paste M
Page 92 and 93:
CHAPTER 8 PACKAGING 8 In this chapt
Page 94 and 95:
PACKAGING 8 Reel The 13-inch reel t
Page 96 and 97:
CHAPTER 9 SHIPPING and HANDLING 9 I
Page 98 and 99:
SHIPPING and HANDLING 9 Moisture Pr
Page 100 and 101:
SHIPPING and HANDLING 9 Recommended
Page 102 and 103:
SHIPPING and HANDLING 9 Grounding t
Page 104 and 105:
CHAPTER 10 COPERNICUS REFERENCE BOA
Page 106 and 107:
COPERNICUS REFERENCE BOARD 10 IMAGE
Page 108 and 109:
COPERNICUS REFERENCE BOARD 10 Refer
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
CHAPTER 11 FIRMWARE UPGRADE 11 In t
Page 116 and 117:
FIRMWARE UPGRADE 11 Firmware Binary
Page 118 and 119:
FIRMWARE UPGRADE 11 Pseudo-Code Exp
Page 120 and 121:
FIRMWARE UPGRADE 11 Error Recovery
Page 122 and 123:
FIRMWARE UPGRADE 11 Packet ID - 0x8
Page 124 and 125:
FIRMWARE UPGRADE 11 Packet ID - 0x8
Page 126 and 127:
FIRMWARE UPGRADE 11 Loading Firmwar
Page 128 and 129:
APPENDIX A TRIMBLE STANDARD INTERFA
Page 130 and 131:
TRIMBLE STANDARD INTERFACE PROTOCOL
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169: TRIMBLE STANDARD INTERFACE PROTOCOL
Page 194 and 195: APPENDIX B TRIMBLE ASCII INTERFACE
Page 196 and 197: TRIMBLE ASCII INTERFACE PROTOCOL (T
Page 220 and 221: APPENDIX C NMEA 0183 C In this appe
Page 222 and 223: NMEA 0183 C The NMEA 0183 Communica
Page 224 and 225: NMEA 0183 C Note - Spaces are only
Page 226 and 227: NMEA 0183 C General NMEA Parser Req
Page 228 and 229: NMEA 0183 C Table C.4 Copernicus GP
Page 230 and 231: NMEA 0183 C GLL - Geographic Positi
Page 232 and 233: NMEA 0183 C RMC - Recommended Minim
Page 234 and 235: NMEA 0183 C AH - Almanac Health Thi
Page 236 and 237: NMEA 0183 C AS - Almanac Status Thi
Page 238 and 239: NMEA 0183 C EP - Ephemeris This sen
Page 240 and 241: NMEA 0183 C IO Ionosphere This sent
Page 242 and 243: NMEA 0183 C PS - PPS Configuration
Page 244 and 245: NMEA 0183 C RT - Reset This sentenc
Page 246 and 247: NMEA 0183 C Table C.29 SG - Set Bit
Page 248 and 249: NMEA 0183 C TF - Receiver Status an
Page 250 and 251: NMEA 0183 C VR - Version This sente
show all

REFERENCE MANUAL - FTP Directory Listing - Trimble

Create successful ePaper yourself

Delete template?

Save as template?