REFERENCE MANUAL - FTP Directory Listing - Trimble

More documents

Recommendations

Info

TRIMBLE ASCII INTERFACE PROTOCOL (TAIP) B Sample PV Message The Position/Velocity Solution (PV) message is one of the more commonly used TAIP messages and most receivers using TAIP are set by default to output the PV message once every 5 seconds. The following analysis of a typical PV message is provided to further explain the TAIP message protocol. >RPV15714+3739438-1220384601512612;ID=1234;*7F Start of message delimiter R Response qualifier PV PV message identifier 15714 GPS time of day +3739438 Latitude -12203846 Longitude 015 Speed 126 Heading 1 Source of data 2 Age of data ;ID=1234 Vehicle ID ;*7F Checksum < End of message delimiter Note – See PV Position/Velocity Solution, page 200, for more detail on the interpretation of this message. Copernicus GPS Receiver 189
B TRIMBLE ASCII INTERFACE PROTOCOL (TAIP) Time and Distance Reporting The ’D’ message qualifier allows you to specify a minimum distance traveled as well as a minimum and maximum time interval for the next report. Units that are stationed at a fixed location can be programmed to report only when the unit moves “off station” or after a certain elapsed time since last report, but no more often than the specified minimum time interval. The message format used with the ’D’ qualifier is shown below: >DAABBBBCCCCEEEEFFFF[;ID=GGGG][;*HH]< The distance ‘D’ in the message refers to the radial distance. A message would be issued if the receiver has moved farther than a radius of ‘D’ away from where it was previously reported. If the accumulated distance traveled is longer than ‘D’ but the final location is still within the radius of ‘D’ (e.g. circling many times around a closed perimeter of radius smaller than ‘D’), then no message would be issued. ID Meaning > Start of message delimiter D Distance message qualifier AA Message to report (i.e. PV means Position Velocity message) BBBB Minimum time (seconds) interval between reports ( T interval) CCCC Report epoch (number of seconds from top of the hour) EEEE Delta distance (meters) from last reported distance FFFF Maximum time (seconds) interval between reports ( T max) GGGG Optional vehicle identification number (user selected) HH Optional checksum < End of message delimiter Note – If BBBB = 0, then the message output is disabled. If FFFF = 0, maximum time feature is disabled (the unit will only report if current position is greater than or equal to the delta distance specified in EEEE). Example When the message: >DPV0030000505000900;ID=0105< is sent to the GPS receiver, it specifies that vehicle number 105 (GGGG = 0105) is to report the Position Velocity message (AA = PV) whenever its current position differs from the previously reported position by at least 500 meters (EEEE = 0500), but no more often than every 30 seconds (BBBB = 0030) or less often than every 15 minutes (FFFF = 0900 seconds). The minimum and maximum time-out reports are to be issued with a 5 second offset (CCCC = 0005) from the top of the hour. The optional checksum was not used in this example. The square brackets, [...], shown in the format description above are used to indicate optional data. The brackets themselves are never included in the actual TAIP message string. 190 Copernicus GPS Receiver
Page 1 and 2:
REFERENCE MANUAL Copernicus GPS Re
Page 3 and 4:
Corporate Office Trimble Navigation
Page 6 and 7:
Table of Contents Table of Contents
Page 8 and 9:
Table of Contents 7 MECHANICAL SPEC
Page 10 and 11:
Table of Contents Command Packet 0x
Page 12 and 13:
Table of Contents X1 Extended Statu
Page 14 and 15:
CHAPTER 1 STARTER KIT 1 In this cha
Page 16 and 17:
STARTER KIT 1 Starter Kit The Coper
Page 18 and 19:
STARTER KIT 1 Figure 1.3 USB Cable
Page 20 and 21:
STARTER KIT 1 Interface Connections
Page 22 and 23:
STARTER KIT 1 Removing the Referenc
Page 24 and 25:
STARTER KIT 1 Quick Start Guide 1.
Page 26 and 27:
STARTER KIT 1 Trimble GPS Monitor T
Page 28 and 29:
STARTER KIT 1 4. Click the Device M
Page 30 and 31:
STARTER KIT 1 Connect to the GPS Re
Page 32 and 33:
STARTER KIT 1 Configure GPS Ports 1
Page 34 and 35:
STARTER KIT 1 Configure PPS Output
Page 36 and 37:
STARTER KIT 1 Creating a Log Follow
Page 38 and 39:
STARTER KIT 1 3. Select one of the
Page 40 and 41:
CHAPTER 2 PRODUCT DESCRIPTION 2 In
Page 42 and 43:
PRODUCT DESCRIPTION 2 Block Diagram
Page 44 and 45:
PRODUCT DESCRIPTION 2 Electrical El
Page 46 and 47:
PRODUCT DESCRIPTION 2 Absolute Mini
Page 48 and 49:
PRODUCT DESCRIPTION 2 Power Consump
Page 50 and 51:
CHAPTER 3 INTERFACE CHARACTERISTICS
Page 52 and 53:
INTERFACE CHARACTERISTICS 3 Pin Des
Page 54 and 55:
INTERFACE CHARACTERISTICS 3 Table 3
Page 56 and 57:
INTERFACE CHARACTERISTICS 3 Serial
Page 58 and 59:
INTERFACE CHARACTERISTICS 3 Acquiri
Page 60 and 61:
INTERFACE CHARACTERISTICS 3 Enablin
Page 62 and 63:
CHAPTER 4 OPERATING MODES 4 In this
Page 64 and 65:
OPERATING MODES 4 Changing the Run/
Page 66 and 67:
OPERATING MODES 4 Serial Port Activ
Page 68 and 69:
OPERATING MODES 4 Saving Almanac, E
Page 70 and 71:
CHAPTER 5 APPLICATION CIRCUITS 5 In
Page 72 and 73:
APPLICATION CIRCUITS 5 Figure 5.2 P
Page 74 and 75:
APPLICATION CIRCUITS 5 • Antenna
Page 76 and 77:
APPLICATION CIRCUITS 5 Following is
Page 78 and 79:
CHAPTER 6 RF LAYOUT CONSIDERATIONS
Page 80 and 81:
RF LAYOUT CONSIDERATIONS 6 In the p
Page 82 and 83:
RF LAYOUT CONSIDERATIONS 6 PCB Cons
Page 84 and 85:
RF LAYOUT CONSIDERATIONS 6 Striplin
Page 86 and 87:
CHAPTER 7 MECHANICAL SPECIFICATIONS
Page 88 and 89:
MECHANICAL SPECIFICATIONS 7 Solderi
Page 90 and 91:
MECHANICAL SPECIFICATIONS 7 Paste M
Page 92 and 93:
CHAPTER 8 PACKAGING 8 In this chapt
Page 94 and 95:
PACKAGING 8 Reel The 13-inch reel t
Page 96 and 97:
CHAPTER 9 SHIPPING and HANDLING 9 I
Page 98 and 99:
SHIPPING and HANDLING 9 Moisture Pr
Page 100 and 101:
SHIPPING and HANDLING 9 Recommended
Page 102 and 103:
SHIPPING and HANDLING 9 Grounding t
Page 104 and 105:
CHAPTER 10 COPERNICUS REFERENCE BOA
Page 106 and 107:
COPERNICUS REFERENCE BOARD 10 IMAGE
Page 108 and 109:
COPERNICUS REFERENCE BOARD 10 Refer
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
CHAPTER 11 FIRMWARE UPGRADE 11 In t
Page 116 and 117:
FIRMWARE UPGRADE 11 Firmware Binary
Page 118 and 119:
FIRMWARE UPGRADE 11 Pseudo-Code Exp
Page 120 and 121:
FIRMWARE UPGRADE 11 Error Recovery
Page 122 and 123:
FIRMWARE UPGRADE 11 Packet ID - 0x8
Page 124 and 125:
FIRMWARE UPGRADE 11 Packet ID - 0x8
Page 126 and 127:
FIRMWARE UPGRADE 11 Loading Firmwar
Page 128 and 129:
APPENDIX A TRIMBLE STANDARD INTERFA
Page 130 and 131:
TRIMBLE STANDARD INTERFACE PROTOCOL
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149: TRIMBLE STANDARD INTERFACE PROTOCOL
Page 194 and 195: APPENDIX B TRIMBLE ASCII INTERFACE
Page 196 and 197: TRIMBLE ASCII INTERFACE PROTOCOL (T
Page 220 and 221: APPENDIX C NMEA 0183 C In this appe
Page 222 and 223: NMEA 0183 C The NMEA 0183 Communica
Page 224 and 225: NMEA 0183 C Note - Spaces are only
Page 226 and 227: NMEA 0183 C General NMEA Parser Req
Page 228 and 229: NMEA 0183 C Table C.4 Copernicus GP
Page 230 and 231: NMEA 0183 C GLL - Geographic Positi
Page 232 and 233: NMEA 0183 C RMC - Recommended Minim
Page 234 and 235: NMEA 0183 C AH - Almanac Health Thi
Page 236 and 237: NMEA 0183 C AS - Almanac Status Thi
Page 238 and 239: NMEA 0183 C EP - Ephemeris This sen
Page 240 and 241: NMEA 0183 C IO Ionosphere This sent
Page 242 and 243: NMEA 0183 C PS - PPS Configuration
Page 244 and 245: NMEA 0183 C RT - Reset This sentenc
Page 246 and 247: NMEA 0183 C Table C.29 SG - Set Bit
Page 248 and 249:
NMEA 0183 C TF - Receiver Status an
Page 250 and 251:
NMEA 0183 C VR - Version This sente
show all

REFERENCE MANUAL - FTP Directory Listing - Trimble

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?