Carbon Nanotube Reinforced Composites: Metal and Ceramic ...

Materials Science Forum, 534–536 (Pt2),
889–892.
42 Fogagnolo, J.B., Ruiz-Navas, E.M.,
Robert, M.H. and Torralba, J.M. (2003)
The effects of mechanical alloying on the
compressibility of aluminum composite
powder. Materials Science and Engineering
A, 355, 50–55.
43 Fogagnolo, J.B., Velasco, F., Robert, M.H.
and Torralba, J.M. (2003) Effect of
mechanical alloying on the morphology,
microstructure and properties of
aluminum matrix composite powders.
Materials Science and Engineering A,
342, 131–143.
44 Suryanarayana, C. (2001) Mechanical
alloying and milling. Progress in Materials
Science, 46, 1–184.
45 Kamrani, S., Simchi, A., Riedel, R. and
Seyed Reihani, S.M. (2007) Effect of
reinforcement volume fraction on
mechanical alloying of Al-SiC
nanocomposite powders. Powder
Metallurgy, 50, 276–282.
46 He, C., Zhao, N., Shi, C., Du, X., Li, J.,
Li, H. and Cui, Q. (2007) An approach
to obtaining homogeneously dispersed
carbon nanotubes in Al powders for
preparing reinforced Al-matrix
composites. Advanced Materials,
19, 1128–1132.
47 Valiev, R.Z., Zehetbauer, M.J., Estin, Y.,
Hoeppel, H.W., Ivanisenko, Y., Hahn, H.,
Wilde, G., Roven, H.J., Sauvage, X. and
Langdon, T.G. (2007) The innovation
potential of nanostructured materials.
Advanced Engineering Materials, 9,
527–533.
48 Lee, S., Berbon, P.B., Furukawa, M.,
Horita, Z., Nemoto, M., Tsenev, N.K.,
Valiev, R.Z. and Langdon, T.G. (1999)
Developing superplastic properties in
aluminum alloy through severe plastic
deformation. Materials Science and
Engineering A, 272, 63–72.
49 Saravanan, M., Pillai, R.M., Ravi, K.R.,
Pai, B.C. and Brahmakumar, M. (2007)
Development of ultrafine grain
aluminum-graphite metal matrix
Referencesj83
composite by equal channel angular
pressing. Composites Science and
Technology, 67, 1275–1279.
50 Sabirov, I., Kolednik, O., Valiev, R.Z.
and Pippan, R. (2005) Equal
channel angular pressing of metal
matrix composites: Effect on particle
distribution and fracture toughness.
Acta Materialia, 53, 4919–4930.
51 Stolyarov, V.V., Zhu, Y.T., Lowe, T.C.,
Islamgaliev, R.K. and Valiev, R.Z. (2000)
Processing nanocrystalline Ti and its
nanocomposites from micrometer-sized
Ti powder using high pressure torsion.
Materials Science and Engineering A, 282,
78–85.
52 Tokunaga, T., Kaneko, K. and Horita, Z.
(2008) Production of aluminum-matrix
carbon nanotube composite using high
pressure torsion. Materials Science and
Engineering A, 490, 300–304.
53 Tokunaga, T., Kaneko, K., Sato, K. and
Horita, Z. (2008) Microstructure and
mechanical properties of aluminumfullerene
composite fabricated by high
pressure torsion. Scripta Materialia, 58,
735–738.
54 Housh, S., Mikucki, B. and Stevenson, A.
(1990) Selection and application of
magnesium and magnesium alloys,
in ASM Handbook: Properties and
Selection: Nonferrous Alloys and
Special-Purpose Materials, vol. 2, ASM
International, Materials Park, Ohio, USA,
DOI:10.1361/asmhba0001074.
55 Xie, W., Liu, Y., Li, D.S., Zhang, J., Zhang,
Z.W. and Bi, J. (2007) Influence of
sintering routes to the mechanical
properties of magnesium alloy and its
composites produced by PM technique.
Journal of Alloys and Compounds, 431,
162–166.
56 Ferkel, H. and Mordike, B.L. (2001)
Magnesium strengthened by SiC
nanoparticles. Materials Science and
Engineering A, 298, 193–199.
57 Cao, G., Konishi, H. and Li, X. (2008)
Mechanical properties and
microstructure of SiC-reinforced Mg-