User Manual 08/2003 Edition

More documents

Recommendations

Info

5 5 Description of the Functions 02.99 04.01 08.03 5.6 Parameters for SIMODRIVE POSMO A P0029 / 1D Electronics temperature tolerance time 300W 075W Min Standard Max Unit Data type Effective 0 120000 2000000 ms T4 immed. For an electronics overtemperature condition, after this time, the warning is changed to a fault, i.e. the appropriate response is activated. Note: The electronics temperature is displayed using P47. Input resolution = 10 ms The parameter value can be changed while traversing. P0030 / 1E 300W 075W Fault suppression Min Standard Max Unit Data type Effective 0 0 F Hex I2 immed. If the bit is set, instead of the appropriate fault, only a warning is output. Bit 0: Speed controller at its endstop Bit 1: Start, software limit switch or end, software limit switch Software limit switches always stop an axis. Bit 2: Standstill monitoring Bit 3: Undervoltage of the load current supply (from SW 1.6) Note: The parameter value can be changed while traversing. P0031 / 1F 300W 075W Function terminal 1 Min Standard Max Unit Data type Effective 0 0 479 – I2 immed. The function of the terminal is defined using this parameter: The following applies from SW 2.0: The meaning of terminal parameterization depends on the operating mode (P930). Parameters with different meanings are marked. Parameters which are not marked have the same function in both operating modes. 0 No function 1 I (STW.4) Positioning operating mode: Operating condition positioning. Stop and reject the actual traversing task on cancelation. Stop Speed setpoint operating mode: Ramp-function generator enable. Stop with maximum acceleration on cancelation. 2 I (STW.5) Positioning operating mode: Operating condition positioning. Stop without rejecting the actual traversing task on cancelation. Stop Speed setpoint operating mode: Ramp-function generator START / Rampfunction generator STOP. The actual speed remains constant on cancelation. 3 I (STW.6) Positioning operating mode: Activate traversing task Speed setpoint operating mode: Setpoint enable. Deceleration at the ramp on cancelation. 4 I (STW.8) Positioning operating mode: Jogging – Speed setpoint operating mode: No function 5 I (STW.9) Positioning operating mode: Jogging + Speed setpoint operating mode: No function 6 I (STW.11) Positioning operating mode: Referencing Speed setpoint operating mode: No function 7 I (STW.12) Positioning operating mode: Automatic single block. Speed setpoint operating mode: No function 5-192 Siemens AG 2003 All rights reserved SIMODRIVE POSMO A User Manual (POS1) – 08.03 Edition
02.99 04.01 08.03 Siemens AG 2003 All rights reserved SIMODRIVE POSMO A User Manual (POS1) – 08.03 Edition 5 Description of the Functions 5.6 Parameters for SIMODRIVE POSMO A 8 I (STW.13) Positioning operating mode: External block change. Speed setpoint operating mode: No function 9 I (STW.14) Positioning operating mode: Read-in enable. Speed setpoint operating mode: No function 10 I (RMB.0) Positioning operating mode: Accept value directly in checkback byte (bit 0). Speed setpoint operating mode: No function 11 I (RMB.1) Positioning operating mode: Accept value directly in checkback byte (bit 1). Speed setpoint operating mode: No function 12 I (RMB.2) Positioning operating mode: Accept value directly in checkback byte (bit 2). Speed setpoint operating mode: No function 13 I (RMB.3) Positioning operating mode: Accept value directly in checkback byte (bit 3). Speed setpoint operating mode: No function 14 I (RMB.4) Positioning operating mode: Accept value directly in checkback byte (bit 4). Speed setpoint operating mode: No function 15 I (RMB.5) Positioning operating mode: Accept value directly in checkback byte (bit 5). Speed setpoint operating mode: No function 16 I (RMB.6) Positioning operating mode: Accept value directly in checkback byte (bit 6). Speed setpoint operating mode: No function 17 I (RMB.7) Positioning operating mode: Accept value directly in checkback byte (bit 7). Speed setpoint operating mode: No function 18 I (STB.0) Positioning operating mode: Accept value directly in start byte (bit 0). Speed setpoint operating mode: No function 19 I (STB.1) Positioning operating mode: Accept value directly in start byte (bit 1). Speed setpoint operating mode: No function 20 I (STB.2) Positioning operating mode: Accept value directly in start byte (bit 2). Speed setpoint operating mode: No function 21 I (STB.3) Positioning operating mode: Accept value directly in start byte (bit 3). Speed setpoint operating mode: No function 22 I (STB.4) Positioning operating mode: Accept value directly in start byte (bit 4). Speed setpoint operating mode: No function 23 I (STB.5) Positioning operating mode: Accept value directly in start byte (bit 5). Speed setpoint operating mode: No function 24 I (STB.6) Positioning operating mode: Accept value directly in start byte (bit 6). Speed setpoint operating mode: No function 25 I (STB.7) Positioning operating mode: Accept value directly in start byte (bit 7). Speed setpoint operating mode: No function 26 I (STB.15) Open holding brake (software version 1.4 and higher) 27 I Positioning operating mode: On-the-fly measurement / actual value setting (software version 1.4 and higher) This function is only possible via terminal 1. Other input parameters can also be used. The input is updated in a 125 microsecond grid for the function ”On-the-fly measurement / actual value setting”. Speed setpoint operating mode: No function 28 I Start of hardware limit switch 29 I End of hardware limit switch 64 O (ZSW.0) Ready for power-up 65 O (ZSW.1) Ready 66 O (ZSW.2) Operation enabled 67 O (ZSW.3) Fault 68 O (ZSW.4) OFF 2 69 O (ZSW.5) OFF 3 70 O (ZSW.6) Power-on inhibit 71 O (ZSW.7) Warning 5-193 5
Page 1:
User Manual 08/2003 Edition simodri
Page 4 and 5:
3ls SIMODRIVE ® documentation Prin
Page 6 and 7:
Foreword Information about using th
Page 8 and 9:
Foreword Motor version, software re
Page 10 and 11:
Foreword x ! Notice This warning in
Page 12 and 13:
Foreword ESDS instructions xii Elec
Page 14 and 15:
Table of Contents 4 Communications
Page 16 and 17:
Table of Contents xvi Space for you
Page 18 and 19:
1 1 Brief Description 04.01 1.1 Gen
Page 20 and 21:
1 1 Brief Description 04.01 05.03 1
Page 22 and 23:
1 1 Brief Description 04.01 08.01 1
Page 24 and 25:
1 1 Brief Description 04.01 1.3 Saf
Page 26 and 27:
2 2 Installing and Connecting-up 02
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
3 3 Start-up 02.99 3.1 General info
Page 66 and 67:
3 3 Start-up 02.99 05.03 3.2 Commis
Page 68 and 69:
3 3 Start-up 02.99 04.01 05.03 3.2
Page 70 and 71:
3 3 Start-up 02.99 3.2 Commissionin
Page 72 and 73:
3 3 Start-up 02.99 05.03 3.2 Commis
Page 74 and 75:
Page 76 and 77:
3 3 Start-up 02.99 05.03 3.2 Commis
Page 78 and 79:
Page 80 and 81:
3 3 Start-up 02.99 05.03 3.3 Commis
Page 82 and 83:
3 3 Start-up 02.99 04.01 3.3 Commis
Page 84 and 85:
3 3 Start-up 02.99 05.03 3.3 Commis
Page 86 and 87:
3 3 Start-up 02.99 05.03 3.3 Commis
Page 88 and 89:
Page 90 and 91:
4 4 Communications via PROFIBUS DP
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
5 5 Description of the Functions 02
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143: 5 5 Description of the Functions 02
Page 214 and 215: 6 6 Fault Handling and Diagnostics
Page 232 and 233: 7 7 Installation and Service 04.01
Page 240 and 241: A A Abbreviations 04.01 GSD HEX HW
Page 242 and 243:
A A Abbreviations 04.01 STB STW SW
Page 244 and 245:
B B References 05.03 Electronic Doc
Page 246 and 247:
B B References 05.03 B-246 Space fo
Page 248 and 249:
C C Dimension Drawings 02.99 08.03
Page 250 and 251:
Page 252 and 253:
C C Dimension Drawings 02.99 C.2 Di
Page 254 and 255:
Page 256 and 257:
D D EC Declaration of Conformity 08
Page 258 and 259:
D D EC Declaration of Conformity 08
Page 260 and 261:
E E Index 08.03 Diagnostics LED, 1-
Page 262 and 263:
E E Index 08.03 O Offline with Simo
Page 264 and 265:
E E Index 08.03 Shaft load capabili
Page 266 and 267:
E E Index 08.03 E-266 Space for you
Page 269 and 270:
General Documentation/Catalogs SINU
show all

User Manual 08/2003 Edition

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?