User Manual 08/2003 Edition

More documents

Recommendations

Info

5 5 Description of the Functions 02.99 04.01 08.03 5.6 Parameters for SIMODRIVE POSMO A P0097 / 61 Carry-out POWER-ON RESET 300W 075W Min Standard Max Unit Data type Effective 0 0 1 – I2 immed. A POWER-ON RESET for the drive can be carried-out using this parameter. 0 Output status 1 Carry-out POWER ON-RESET Note: After P0097 = 1, POWER ON-RESET is immediately carried-out. Communications is interrupted. The master does not receive an acknowledgment. Available with software version 1.5 and higher. P0098 / 62 300W 075W Reset reference point set Min Standard Max Unit Data type Effective 0 0 1 – I2 immed. 0 No reference point set 1 Note: Reference point set For a stationary, referenced axis, when writing zero into P98 = 0, the ”No reference point set” status is re-established. Refer to ZSW.11 Available from SW 1.4. P0099:21 / 63 Program management 300W 075W Min Standard Max Unit Data type Effective 0 0 27 – I2 immed. The parameter specifies the start of a program. P99:0 ––> no significance P99:1 ––> start, program 1 (standard value = 13) P99:2 ––> start, program 2 (standard value = 18) P99:3 ––> start, program 3 (standard value = 23), etc. Note: The parameter value can be changed while traversing. P0100 / 64 300W 075W Control word simulation Min Standard Max Unit Data type Effective 0 0 FFFF – V2 immed. If the cyclic communication with Master Class 1 is interrupted for more than 3 seconds, this control word is used. All terminal signals remain active with priority. = 0 ––> no simulation = 17471 dec (= 443F hex) Note: ––> value recommended for simulation The parameter value can be changed while traversing. P101 must be > 0. When operating the system with Master Class 2 alone (SimoCom A), the simulation mode is activated immediately when making entries in P100. Available from SW 1.2. 5-204 Siemens AG 2003 All rights reserved SIMODRIVE POSMO A User Manual (POS1) – 08.03 Edition
02.99 04.01 08.03 Siemens AG 2003 All rights reserved SIMODRIVE POSMO A User Manual (POS1) – 08.03 Edition 5.6 Parameters for SIMODRIVE POSMO A P0101:11 / 65 Block sequence in standalone operation 5 Description of the Functions 300W 075W Min Standard Max Unit Data type Effective 0 0 27 – I2 immed. For standalone operation, a maximum of 10 traversing blocks can be entered in the range 3 to 27 in P101:11. These specified blocks are executed one after the other in the standalone mode. P101:0 ––> no significance P101:1 ––> 1st block P101:2 ––> 2nd block, etc. Note: The parameter value can be changed while traversing. Available from SW 1.2. P0700 / 2BC Operating mode selector switch 300W 075W Min Standard Max Unit Data type Effective 1 2 2 – I2 PO This parameter is used for selecting the operating mode. Operating mode changes only take effect when the parameter set is saved in the FEPROM (P971 0 ––> 1) followed by a Power-On Reset (P097 0 ––> 1). If SimoCom A is in use, the operating mode should be selected via the configuration dialog. The following operating modes are supported: 1 ––> Speed setpoint 2 ––> Positioning The parameter corresponds to parameter 930. Note: Before changing the operating mode load factory default setting via P970. This allows achieving a pre-defined initial status. Available with software version 2.0 and higher. P0880 / 370 300W 075W N-SETPOINT normalization Min Standard Max Unit Data type Effective –100000 4096 100000 rpm C4 immed. This parameter defines the normalization as to which speed sets in at the gear output when a setpoint of 1000h (4096d) is specified via the control word (STW). P0918 / 396 300W 075W PROFIBUS node address Min Standard Max Unit Data type Effective – – – – I2 RO The node address is read from address switch S1. P0928 / 3A0 300W 075W Control authority PZD Min Standard Max Unit Data type Effective 1 1 2 – V2 immed. Request for control authority from a Class 2 DP master. Note: Available from SW 1.4. 5-205 5
Page 1:
User Manual 08/2003 Edition simodri
Page 4 and 5:
3ls SIMODRIVE ® documentation Prin
Page 6 and 7:
Foreword Information about using th
Page 8 and 9:
Foreword Motor version, software re
Page 10 and 11:
Foreword x ! Notice This warning in
Page 12 and 13:
Foreword ESDS instructions xii Elec
Page 14 and 15:
Table of Contents 4 Communications
Page 16 and 17:
Table of Contents xvi Space for you
Page 18 and 19:
1 1 Brief Description 04.01 1.1 Gen
Page 20 and 21:
1 1 Brief Description 04.01 05.03 1
Page 22 and 23:
1 1 Brief Description 04.01 08.01 1
Page 24 and 25:
1 1 Brief Description 04.01 1.3 Saf
Page 26 and 27:
2 2 Installing and Connecting-up 02
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
3 3 Start-up 02.99 3.1 General info
Page 66 and 67:
3 3 Start-up 02.99 05.03 3.2 Commis
Page 68 and 69:
3 3 Start-up 02.99 04.01 05.03 3.2
Page 70 and 71:
3 3 Start-up 02.99 3.2 Commissionin
Page 72 and 73:
3 3 Start-up 02.99 05.03 3.2 Commis
Page 74 and 75:
Page 76 and 77:
3 3 Start-up 02.99 05.03 3.2 Commis
Page 78 and 79:
Page 80 and 81:
3 3 Start-up 02.99 05.03 3.3 Commis
Page 82 and 83:
3 3 Start-up 02.99 04.01 3.3 Commis
Page 84 and 85:
3 3 Start-up 02.99 05.03 3.3 Commis
Page 86 and 87:
3 3 Start-up 02.99 05.03 3.3 Commis
Page 88 and 89:
Page 90 and 91:
4 4 Communications via PROFIBUS DP
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
5 5 Description of the Functions 02
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155: 5 5 Description of the Functions 02
Page 214 and 215: 6 6 Fault Handling and Diagnostics
Page 232 and 233: 7 7 Installation and Service 04.01
Page 240 and 241: A A Abbreviations 04.01 GSD HEX HW
Page 242 and 243: A A Abbreviations 04.01 STB STW SW
Page 244 and 245: B B References 05.03 Electronic Doc
Page 246 and 247: B B References 05.03 B-246 Space fo
Page 248 and 249: C C Dimension Drawings 02.99 08.03
Page 250 and 251: C C Dimension Drawings 02.99 08.03
Page 252 and 253: C C Dimension Drawings 02.99 C.2 Di
Page 254 and 255:
C C Dimension Drawings 02.99 05.03
Page 256 and 257:
D D EC Declaration of Conformity 08
Page 258 and 259:
D D EC Declaration of Conformity 08
Page 260 and 261:
E E Index 08.03 Diagnostics LED, 1-
Page 262 and 263:
E E Index 08.03 O Offline with Simo
Page 264 and 265:
E E Index 08.03 Shaft load capabili
Page 266 and 267:
E E Index 08.03 E-266 Space for you
Page 269 and 270:
General Documentation/Catalogs SINU
show all

User Manual 08/2003 Edition

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?