User Manual 08/2003 Edition
User Manual 08/2003 Edition
User Manual 08/2003 Edition
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
2<br />
2 Installing and Connecting–up 02.99 05.03<br />
2.5 Gearbox selection<br />
2.5 Gearbox selection<br />
2.5.1 Gearboxes for SIMODRIVE POSMO A –75 W<br />
Modular gearbox,<br />
75 W motor<br />
2-52<br />
For SIMODRIVE POSMO A – 75 W, the following gearboxes can be<br />
selected and used according to Table 2-4:<br />
Table 2-4 System data, modular gearbox with planetary/worm gearboxes<br />
Gearbox Stage StepEffi- Torque Rated<br />
type num- number<br />
down<br />
ratio<br />
ciency<br />
Permissible<br />
speed<br />
1) ber ratio<br />
Available<br />
speed<br />
S1 short S1 S3 n<br />
term<br />
25 %<br />
1 min<br />
(S1)<br />
iGearbox Gearbox [Nm] [Nm] [Nm] [Nm] [RPM]<br />
Without<br />
gearbox<br />
Planetary<br />
gearbox<br />
– – – – – 0.18 0.36 3300<br />
1<br />
4.5 0.85 1.2 2.4 0.7 1.4 733<br />
8 0.85 1.2 2.4 1.2 2.4 413<br />
20.25 0.72 8 16 2.6 5.2 163<br />
2 36 0.72 8 16 4.7 9.3 92<br />
50 0.72 8 16 6.5 13.0 66<br />
3<br />
126.5625 0.61 24 48 13.9 27.8 26<br />
162 0.61 24 48 17.8 35.6 20<br />
5 0.70 2 4 0.6 1.3 660<br />
Worm<br />
gear2)3) gear<br />
1 24 0.50 3.5 7 2.2 4.3 138<br />
2)3) 1<br />
75 0.25 4 8 3.4 6.8 44<br />
1) The specified permissible gearbox torque may not be exceeded.<br />
Gearboxes can be briefly loaded (1 – 2 s when starting) with higher torques up to a maximum of twice the<br />
continuous torque without causing permanent damage (but this does have a negative impact on the<br />
gearbox lifetime). The gearbox could be destroyed if this limit is exceeded.<br />
The current limits of the positioning motor are preset in the factory so that gearboxes cannot be destroyed<br />
due to being over–stressed.<br />
2) Notice: If the worm gear has to be rotated due to the mechanical design, then the mounting screws must<br />
be subsequently tightened to a torque of 2 Nm and secured using Loctite 274. No warranty is accepted<br />
for damage caused by incorrect changes.<br />
3) Torsional play < 1°<br />
Reader’s note<br />
Additional gearbox data ––> refer to Chapter 2.6.1<br />
Dimension drawings of motors<br />
and gearboxes ––> refer to Chapter C.1<br />
Gearbox-dependent parameters ––> refer to Chapter 5.6.3<br />
Siemens AG <strong>2003</strong> All rights reserved<br />
SIMODRIVE POSMO A <strong>User</strong> <strong>Manual</strong> (POS1) – <strong>08</strong>.03 <strong>Edition</strong>