User Manual 08/2003 Edition

More documents

Recommendations

Info

5 5 Description of the Functions 02.99 04.01 5.6 Parameters for SIMODRIVE POSMO A 5-212 Space for your notes Siemens AG 2003 All rights reserved SIMODRIVE POSMO A User Manual (POS1) – 08.03 Edition
Fault Handling and Diagnostics 6.1 LED fault display LED fault display An LED with the following significance is provided on the rear of the positioning motor for diagnostics LED: Table 6-1 What does an LED mean when it is bright? LED display Is the What status does the drive have? Color How is it lit? bus OK? What are the fault possibilities? None Off No The equipment is powered down or is defective The power supply is incorrectly connected (incorrect polarity) Red Steady light No Critical hardware defect, CPU cannot be used Briefly after power up, even if the unit is OK Disappears after the system has completely run up. Flashing light Yes Fault present, drive not ready Read–out the fault number ––> refer to Chapter 6.2 Red/yellow Alternating flashing light No Bus communications interrupted Green Yellow Yellow/ green (from SW 1.2) Steady light Yes Standard operation Flashing light Yes Run–up, bus being initialized (baud rate adjustment, configuration, parameterization) No bus connection established: – Bus cables not OK – Address incorrectly set – Bus parameterizing error Steady light No Bus run–up, incorrect configuration telegram Flashing light No Bus run–up, incorrect parameterizing telegram Alternating flashing light Siemens AG 2003 All rights reserved SIMODRIVE POSMO A User Manual (POS1) – 08.03 Edition No Standalone operation is active ––> refer to Chapter 5.5.12 6 6-213 6
Page 1:
User Manual 08/2003 Edition simodri
Page 4 and 5:
3ls SIMODRIVE ® documentation Prin
Page 6 and 7:
Foreword Information about using th
Page 8 and 9:
Foreword Motor version, software re
Page 10 and 11:
Foreword x ! Notice This warning in
Page 12 and 13:
Foreword ESDS instructions xii Elec
Page 14 and 15:
Table of Contents 4 Communications
Page 16 and 17:
Table of Contents xvi Space for you
Page 18 and 19:
1 1 Brief Description 04.01 1.1 Gen
Page 20 and 21:
1 1 Brief Description 04.01 05.03 1
Page 22 and 23:
1 1 Brief Description 04.01 08.01 1
Page 24 and 25:
1 1 Brief Description 04.01 1.3 Saf
Page 26 and 27:
2 2 Installing and Connecting-up 02
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
3 3 Start-up 02.99 3.1 General info
Page 66 and 67:
3 3 Start-up 02.99 05.03 3.2 Commis
Page 68 and 69:
3 3 Start-up 02.99 04.01 05.03 3.2
Page 70 and 71:
3 3 Start-up 02.99 3.2 Commissionin
Page 72 and 73:
3 3 Start-up 02.99 05.03 3.2 Commis
Page 74 and 75:
Page 76 and 77:
3 3 Start-up 02.99 05.03 3.2 Commis
Page 78 and 79:
Page 80 and 81:
3 3 Start-up 02.99 05.03 3.3 Commis
Page 82 and 83:
3 3 Start-up 02.99 04.01 3.3 Commis
Page 84 and 85:
3 3 Start-up 02.99 05.03 3.3 Commis
Page 86 and 87:
3 3 Start-up 02.99 05.03 3.3 Commis
Page 88 and 89:
Page 90 and 91:
4 4 Communications via PROFIBUS DP
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
5 5 Description of the Functions 02
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163: 5 5 Description of the Functions 02
Page 214 and 215: 6 6 Fault Handling and Diagnostics
Page 232 and 233: 7 7 Installation and Service 04.01
Page 240 and 241: A A Abbreviations 04.01 GSD HEX HW
Page 242 and 243: A A Abbreviations 04.01 STB STW SW
Page 244 and 245: B B References 05.03 Electronic Doc
Page 246 and 247: B B References 05.03 B-246 Space fo
Page 248 and 249: C C Dimension Drawings 02.99 08.03
Page 252 and 253: C C Dimension Drawings 02.99 C.2 Di
Page 256 and 257: D D EC Declaration of Conformity 08
Page 258 and 259: D D EC Declaration of Conformity 08
Page 260 and 261: E E Index 08.03 Diagnostics LED, 1-
Page 262 and 263:
E E Index 08.03 O Offline with Simo
Page 264 and 265:
E E Index 08.03 Shaft load capabili
Page 266 and 267:
E E Index 08.03 E-266 Space for you
Page 269 and 270:
General Documentation/Catalogs SINU
show all

User Manual 08/2003 Edition

Create successful ePaper yourself

Delete template?

Save as template?