User Manual 08/2003 Edition

More documents

Recommendations

Info

5 5 Description of the Functions 02.99 04.01 05.03 5.6 Parameters for SIMODRIVE POSMO A 5.6.3 Gearbox–dependent parameters, factory defaults Gearbox– dependent parameters 5-210 Depending on the gearbox used, the parameters listed in Table 5-10 are pre–set before the equipment is supplied: Table 5-10 Gearbox–dependent parameters (factory presetting – default) Type Gearbox P964:7 P3 P10 P16 P22 P28 Step– down ratio iGearbox Gearbox code Gearbox stepdown ratio Maximum velocity 75 W motor: Gearbox–dependent parameters (factory default) Maximum overcurrent Maximum acceleration Maximum current – [mm/min] [A] [mm/s 2 ] [A] Without gearbox 2049 1 30000 9.0 1000 9.0 Planetary gearbox 4.5 2050 4.5 6660 9.0 225 7.8 8 2058 8 3750 7.5 125 4.6 20.25 2059 20.25 1480 9.0 50 9.0 36 2060 36 830 9.0 30 7.9 50 2061 50 600 8.0 20 5.6 126.5625 2062 126.5625 237 9.0 8 7.8 162 2063 162 185 7.4 6 6.0 5 2064 5 6000 9.0 200 9.0 Worm gear 24 2065 24 1250 7.3 40 7.3 75 2066 75 400 5.3 13 5.3 Siemens AG 2003 All rights reserved SIMODRIVE POSMO A User Manual (POS1) – 08.03 Edition
02.99 04.01 05.03 Siemens AG 2003 All rights reserved SIMODRIVE POSMO A User Manual (POS1) – 08.03 Edition 5.6 Parameters for SIMODRIVE POSMO A Table 5-10 Gearbox–dependent parameters (factory presetting – default), continued Type Gearbox Step– down ratio i Gearbox P964:7 Gearbox code P3 P10 P16 P22 P28 Gearbox stepdown ratio – Maximum velocity [mm/min] 300 W motor: Gearbox–dependent parameters (factory default) Keyway Without Smooth gearbox shaft (without keyway) Planetary gearbox 4 7 12 20 35 49 120 2051 1) 2067 2) 2075 1) 2076 2) 2052 2068 2053 2069 2054 2070 2055 2071 2056 2072 2057 2073 2078 2079 Maximum overcurrent [A] Maximum acceleration [mm/s 2 ] Maximum current [A] 1 30000 21.0 4000 21.0 4 7500 21.0 1000 21.0 7 4285 21.0 570 21.0 12 2500 21.0 330 21.0 20 1500 21.0 200 21.0 35 855 12.6 115 14.8 49 610 9.0 80 10.6 120 250 8.3 33 13.0 1) Upper value ––> gearbox code for the motor without holding brake 2) Lower value ––> gearbox code for the motor with holding brake 5 Description of the Functions Notice After another gearbox type has been mounted, the gearbox–dependent parameters no longer match the gearbox and must therefore be modified corresponding to Table 5-10. P964:7 (gearbox code) can only be changed with ”SimoCom A” using the drive configuration. 5-211 5
Page 1:
User Manual 08/2003 Edition simodri
Page 4 and 5:
3ls SIMODRIVE ® documentation Prin
Page 6 and 7:
Foreword Information about using th
Page 8 and 9:
Foreword Motor version, software re
Page 10 and 11:
Foreword x ! Notice This warning in
Page 12 and 13:
Foreword ESDS instructions xii Elec
Page 14 and 15:
Table of Contents 4 Communications
Page 16 and 17:
Table of Contents xvi Space for you
Page 18 and 19:
1 1 Brief Description 04.01 1.1 Gen
Page 20 and 21:
1 1 Brief Description 04.01 05.03 1
Page 22 and 23:
1 1 Brief Description 04.01 08.01 1
Page 24 and 25:
1 1 Brief Description 04.01 1.3 Saf
Page 26 and 27:
2 2 Installing and Connecting-up 02
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
3 3 Start-up 02.99 3.1 General info
Page 66 and 67:
3 3 Start-up 02.99 05.03 3.2 Commis
Page 68 and 69:
3 3 Start-up 02.99 04.01 05.03 3.2
Page 70 and 71:
3 3 Start-up 02.99 3.2 Commissionin
Page 72 and 73:
3 3 Start-up 02.99 05.03 3.2 Commis
Page 74 and 75:
Page 76 and 77:
3 3 Start-up 02.99 05.03 3.2 Commis
Page 78 and 79:
Page 80 and 81:
3 3 Start-up 02.99 05.03 3.3 Commis
Page 82 and 83:
3 3 Start-up 02.99 04.01 3.3 Commis
Page 84 and 85:
3 3 Start-up 02.99 05.03 3.3 Commis
Page 86 and 87:
3 3 Start-up 02.99 05.03 3.3 Commis
Page 88 and 89:
Page 90 and 91:
4 4 Communications via PROFIBUS DP
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
5 5 Description of the Functions 02
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161: 5 5 Description of the Functions 02
Page 214 and 215: 6 6 Fault Handling and Diagnostics
Page 232 and 233: 7 7 Installation and Service 04.01
Page 240 and 241: A A Abbreviations 04.01 GSD HEX HW
Page 242 and 243: A A Abbreviations 04.01 STB STW SW
Page 244 and 245: B B References 05.03 Electronic Doc
Page 246 and 247: B B References 05.03 B-246 Space fo
Page 248 and 249: C C Dimension Drawings 02.99 08.03
Page 252 and 253: C C Dimension Drawings 02.99 C.2 Di
Page 256 and 257: D D EC Declaration of Conformity 08
Page 258 and 259: D D EC Declaration of Conformity 08
Page 260 and 261:
E E Index 08.03 Diagnostics LED, 1-
Page 262 and 263:
E E Index 08.03 O Offline with Simo
Page 264 and 265:
E E Index 08.03 Shaft load capabili
Page 266 and 267:
E E Index 08.03 E-266 Space for you
Page 269 and 270:
General Documentation/Catalogs SINU
show all

User Manual 08/2003 Edition

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?