ISDN ANALYZER D1080 - messkom.de

More documents

Recommendations

Info

ISDN ANALYZER D1080 USER’S MANUAL REV. 5 42 Sabit, used to set the Sa bits value of the transmitted frame in Primary Access. GainRx, used to enable (YES) or disable (NO) a signal amplifier for reception in Primary Access. ! An incorrect setting in this field can cause malfunctioning. ClockTx, used to set the transmission clock in Primary Access: − LOOPED, to transmit with the network clock − INTERNAL, to transmit with an internally generated clock. The second setting is recommended in TE TEST mode. MonChan, selection of the B channel to be extracted on V.11 and/or for audio in monitor function ReqChan, selection of the B channel required by the instrument in the outgoing calls. − ANY, the B channel is set by the network. − B1/2 ÷ 31, the instrument expressly requests the set channel to the network. In QUALITY MEASUREMENT and CALLS GENERATION the B channel requested for the outgoing calls in the same measurement cycle increases starting from the set channel. Ex: if the field is set with the B29 channel, when STARTING the CALLS GENERATION test with 5 calls per cycle, the instrument requests the B29, B30, B31, B1 and B2 channels to the network. CHAPTER 6. SETTING THE INSTRUMENT
USER’S MANUAL REV. 5 ISDN ANALYZER D1080 CdnPlan, used to specify the type of network (that is the ISDN); the possibile options are ISDN or UNKNOWN. The selected value (ISDN or UNKNOWN) is an i.e. contained in the call SETUP. Most networks request the UNKNOWN value (that is do not request to specifiy the ISDN), while others request the ISDN value. The default value is UNKNOWN. It corresponds to the NumPlan field of the earlier firmware versions. CgnType, indicates the type of number called or connected. The options available are: − UNKNOWN; − NATIONAL, for national numbers; − INTERNATIONAL, for international numbers. UsrUsrI, to enter INFO of USER TO USER type in the SETUP and CONNECT messages. The information element for loop tests towards PABX can be entered. The Ascii field displays the ASCII character that corresponds to the entered value. The “?” symbol is displayed in case of non-printable characters. CallsRx, to set the automatic answer to incoming calls and loop the corresponding B channel. The following settings are possible: − ALL ACCEPTED, to accept all incoming calls and loop the corresponding B channels, without checking compatibility. − ONLY COMPATIBLE, to select which incoming calls to accept. The instrument rejects the calls which do not have the profile characteristics set in the Profile field of CHAPTER 6. SETTING THE INSTRUMENT 43
Page 1 and 2: ISDN ANALYZER D1080 USER’S MANUAL
Page 3 and 4: USER’S MANUAL REV. 5 ISDN ANALYZE
Page 15: USER’S MANUAL REV. 5 ISDN ANAL 1.
Page 35: USER’S MANUAL REV. 5 ISDN ANALYZE
Page 93 and 94:
USER’S MANUAL REV. 5 ISDN ANALYZE
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161:
Page 164 and 165:
ISDN ANALYZER D1080 USER’S MANUAL
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 185 and 186:
Page 187:
Page 191 and 192:
Page 193 and 194:
Page 195:
Page 199:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 215 and 216:
Page 217:
show all

ISDN ANALYZER D1080 - messkom.de

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?