ISDN ANALYZER D1080 - messkom.de

More documents

Recommendations

Info

ISDN ANALYZER D1080 USER’S MANUAL REV. 5 44 the CONFIGURATION page. The field is also valid for X.25 calls for which the check on the NUA is activated. − NONE ACCEPTED, to reject all incoming calls. Incoming calls that are not expressly requested by the state of the current test are rejected with cause “D17”. ! In the “CALL WAITING” state, the first incoming call is intercepted by the selected current measurement. Other incoming calls are either looped or rejected according to the value of the CallsRx field. Audio, to select the audio operating mode. In the TE SIMULATOR and TE TEST configuration, the following options are available: − PUSH TO TALK, the internal microphone is only enabled upon request from the operator − HANDS FREE, internal microphone and loudspeaker are enabled − EXTERNAL HANDSET, the operator uses a standard telephone handset connected to the “VF IFC” plug for audio connection − EXTERNAL BY-PASS used for analog measurements with external instruments by means of the “VF IFC” plug In the monitor function, the acoustic monitor can either be enabled for LOUDSPEAKER and EXTERNAL HANDSET or disabled (OFF). Serial, to set the parameters of the V.28 serial port: − Rate, choosing from 600, 1200, 2400, 4800, 9600 and 19200 bit/sec − No bit/character, fixed at 8 − Parity, fixed at no parity − Stop bit, fixed at 1 CHAPTER 6. SETTING THE INSTRUMENT
USER’S MANUAL REV. 5 ISDN ANALYZER D1080 þKeyboardBeep, to activate (YES) or deactivate (NO) the beep sound when pressing a button. The acoustic signal cannot be deactivated for errors. Charge, to activate (YES) or deactivate (NO) the recharging function of the internal batteries. ! To avoid damages, the battery recharging function must be deactivated when non-rechargeable batteries are used. The current voltage value of the batteries is shown in the V. field of the SETTING UP page. If batteries are not present or not correctly positioned, three hyphens appear on the display when the battery recharge circuit is enabled. When the circuit is not enabled, only one hyphen is shown. When the voltage is lower than 4,6 V, a flashing battery appears on the display. Further voltage reductions are indicated with an acoustic signal every two seconds. The functions of commands and setup parameters are shown in the following block diagram. CHAPTER 6. SETTING THE INSTRUMENT 45
Page 1 and 2: ISDN ANALYZER D1080 USER’S MANUAL
Page 3 and 4: USER’S MANUAL REV. 5 ISDN ANALYZE
Page 15: USER’S MANUAL REV. 5 ISDN ANAL 1.
Page 35: USER’S MANUAL REV. 5 ISDN ANALYZE
Page 43: USER’S MANUAL REV. 5 ISDN ANALYZE
Page 95 and 96:
USER’S MANUAL REV. 5 ISDN ANALYZE
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161:
Page 164 and 165:
ISDN ANALYZER D1080 USER’S MANUAL
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 185 and 186:
Page 187:
Page 191 and 192:
Page 193 and 194:
Page 195:
Page 199:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 215 and 216:
Page 217:
show all

ISDN ANALYZER D1080 - messkom.de

Create successful ePaper yourself

Delete template?

Save as template?