memory products - Al Kossow's Bitsavers

ETC2716READ OPERATIONDC CHARACTERISTICS TA=O°C to + 70°C, VCC=5V±5%, Vpp=VCC (2), VSS=OV, (Unless otherwisespecilied)(6)Symbol Parameter Test Conditions Min. Typ. Max. UnitsIII Input Current VIN = VCC or GND - - 10 p,AILO Output Leakage Current VOUT=5.25V, CE/PGM=VIH - - 10 p,AVIL Input Low Voltage -0.1 - 0.8 VVIH(4) Input High Voltage 2.0 - VCC+1 VVOU Output Low Voltage IOL=2.1 mA - - 0.45 VVOHI Output High Voltage IOH= -400 p,A 2.4 - - VVOL2 Output Low Voltage IOL=O p,A - - 0.1 VVOH2 Output High Voltage IOH=O p,A Vcc-0.1 - - VIppi Vpp Supply Current Vpp=5.25V - - 10 p,AICCI VCC Supply Current Active CE/PGM, OE = VIL(TTL Levels) Address = VIH or VIL - 2 10 mAFrequency 1 MHz, I/O = OmAICC2 V CC Supply Current Active CE/PGM = OE = VIL (Note 5)(CMOS Levels) Addresses=GND or VCC - 1 5 mAFrequency 1MHz, 1/0=OmAIccssl V CC Supply Current Standby CE/PGM=VIH - 0,1 1 mAICCSS2 V CC Supply Current Standby CE/PGM=Vcc - 0,01 0,1 mAAC CHARACTERISTICS (TA = O°C to + 70°C, VCC = 5V ±5%, VPP = VCC, VSS = OV; Unless otherwisespecilied)(6).Symbol ETC2716-1 ETC2716 (-V)ParameterTest ConditionsAlternate StandardMin. Max. Min. Max.tACC TAVOV Address to Output Delay CE/PGM=OE=VIL - 350 - 450 nstCE TELOV CE to Output Delay OE=VIL - 350 - 450 nstOE TGLOV Output Enable to CE/PGM=VIL - 120 - 120 nsOutput DelaytOF(5) TGHOZ OE or CE High to CE/PGM=VIL 0 100 0 100 nsOutput Hi-ZtOH TAXOX Address to Output Hold CE/PGM = OE = VIL 0 - 0 - nstoo TEHOZ CE to Output Hi-Z OE=VIL 0 100 0 100 nsUnitCAPACITANCE(3) TA=25°C, 1=1 MHzSymbol Parameter Test Conditions Min. Typ. Max. UnitCI Input Capacitance VIN=OV 4 6 pFCo Output Capacitance VOUT=OV 8 12 pFNotes I. Typical conditions are for operation at: TA=25°C. VCC=5V, Vpp=VCC, and VSS=OV.2. Vpp may be connected to VCC except during program.3. Capacitance is guarallllllld..lly periodic testing. T A = 25°C, f = I MHz ..4. The inputs (Address, OE, CE) may go above VCC by one volt with no latch up danger. Only the output (data inputs duringprogramming) need be..restrk:Jed to VCC + 0.3V.5. T OF is specified for OE or CE which ever occurs first. This parameter is only sampled and not 100% tested.6. TA = - 40·C to + 85·C for "V" range3/993