Service Manual TNC 407 / TNC 415 - heidenhain - DR. JOHANNES ...
Service Manual TNC 407 / TNC 415 - heidenhain - DR. JOHANNES ...
Service Manual TNC 407 / TNC 415 - heidenhain - DR. JOHANNES ...
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Function MP A B C D E F Input AE-6<br />
No. Bit Entry Value<br />
Reference mark evaluation<br />
1320<br />
Š Š Š Š Š Š 0 = positive<br />
Traverse direction for passing over the X<br />
0<br />
+1 = X axis negative<br />
% 00000<br />
reference marks<br />
Y<br />
1<br />
+2 = Y axis negative<br />
(0)<br />
Z<br />
2<br />
+4 = Z axis negative<br />
IV<br />
3<br />
+8 = IV. axis negative<br />
V<br />
4<br />
+16 = V. axis negative<br />
Feed rate for passing over the reference<br />
marks X 1330.0 Š Š Š Š Š Š linear axis:<br />
10 000<br />
Y 1330.1 Š Š Š Š Š Š 10 to 30 000 [mm/min]<br />
10 000<br />
Feed rate for leaving the reference end<br />
Z<br />
IV<br />
V<br />
1330.2<br />
1330.3<br />
1330.4<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
rotary axis:<br />
10 to 30 000 [°/min]<br />
10 000<br />
10 000<br />
10 000<br />
position<br />
X 1331.0 Š Š Š Š Š Š linear axis:<br />
200<br />
(only if MP1350 = 2)<br />
Y 1331.1 Š Š Š Š Š Š 10 to 500 [mm/min]<br />
200<br />
Z<br />
IV<br />
V<br />
1331.2<br />
1331.3<br />
1331.4<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
rotary axis:<br />
10 to 500 [°/min]<br />
200<br />
200<br />
200<br />
Axis sequence for reference mark traverse<br />
0 = no ref. mark traverse<br />
1. axis 1340.0 Š Š Š Š Š Š 1 = X<br />
1<br />
2. axis 1340.1 Š Š Š Š Š Š 2 = Y<br />
2<br />
3. axis<br />
4. axis<br />
5. axis<br />
1340.2<br />
1340.3<br />
1340.4<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
3 =<br />
4 =<br />
5 =<br />
Z<br />
IV<br />
V<br />
3<br />
4<br />
5<br />
Selecting the functional procedure for<br />
0 = position encoder with distance-coded<br />
passing over the reference marks X 1350.0 Š Š Š Š Š Š reference marks (1. mode)<br />
1<br />
Y 1350.1 Š Š Š Š Š Š 1 = position encoder without distance-coded<br />
1<br />
Z<br />
IV<br />
V<br />
1350.2<br />
1350.3<br />
1350.4<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
Š<br />
2 =<br />
3 =<br />
reference marks<br />
special function (linear measurement<br />
with rotary encoder)<br />
position encoder with distance-coded<br />
reference marks (2. mode)<br />
1<br />
1<br />
1<br />
RH<br />
1.0 <strong>TNC</strong> <strong>407</strong>/<strong>415</strong> Machine Parameters MP 1320 - MP 1350.4 16.01.95 10.2 12
Change language