Service Manual TNC 407 / TNC 415 - heidenhain - DR. JOHANNES ...
Service Manual TNC 407 / TNC 415 - heidenhain - DR. JOHANNES ...
Service Manual TNC 407 / TNC 415 - heidenhain - DR. JOHANNES ...
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Kundendienst<br />
HEIDENHAIN<br />
<strong>DR</strong> JOHANNE.s HElDENHAlN GrnbH<br />
D~83292Traunreut.~(08669131-0<br />
14.4 Machine Parameters for the Data Interfaces<br />
SERVICE MANUAL <strong>TNC</strong> <strong>407</strong>/<strong>415</strong><br />
Issue: 01.09.19958<br />
Page 58<br />
The detailed functions of the machine parameters are explained in the <strong>TNC</strong> <strong>Manual</strong> for Machine Tool<br />
Manufacturers and in the information on the data interface FiS232UV24.<br />
In the operating modes ME, FE1 and FE2, the interface parameters are fixed. In the operating modes<br />
EXTI and EXT2, the interface parameters may be determined via machine parameters<br />
All machine parameters for the data interfaces are user parameters, i.e. they can be selected with the<br />
code number 123.<br />
14.4.1 Machine Parameters for the “Standard Interface”<br />
(e.g. for ME 101, printer)<br />
MP for EXTI<br />
5020.0<br />
5030.0<br />
5201 .O<br />
MP for EXT2 Entry Values Function<br />
5020.1 168 7 data bits, transfer stop by DC3, parity bit (even<br />
parity), 1 stop bit<br />
5030.1 0 Standard data interface<br />
5201 .I 3 Control character for end of program = ETX<br />
The data format and the type of transfer stop must be set at the printer according to the values<br />
of MP5020.0 and MP5020.1.<br />
14.4.2 Machine Parameters for “Blockwise Transfer”<br />
(e.g. for FE 401/B, personal computer with HEIDENHAIN data<br />
transfer software)<br />
MP for EXTI MP for EXT2 Entry Values Function<br />
5020.0 5020.1 168 7 data bits, transfer stop by DC3, parity bit (even<br />
parity), 1 stop bit<br />
5030.0 5030.1<br />
12’ Blockwise Transfer<br />
5200.0 5201.1<br />
22’ Control character for program start = STX<br />
5201 .O 5201 .I<br />
32’ Control character for end of program = ETX<br />
5202.0 5202.1<br />
722’ 1. ASCII character for data input = H’l (e.g. H =<br />
NC program in HEIDENHAIN plain language)<br />
5203.0 5203.1 6g21 2. ASCII character for data input = E<br />
5204.0 5204.1 722’ 1. ASCII character for data output = H’l (e.g. H = NC<br />
program in HEIDENHAIN plain language)<br />
5205.0 5205.1 65” 2. ASCII character for data output = A<br />
5206.0 5206.1 12’ ASCII character for start of command block = SOH<br />
5207.0 5207.1 232’ ASCII character for end of command block = ETB<br />
5208.0 5208.1 62’ ASCII character for positive acknowledgement = ACK<br />
5209.0 5209.1 212’ ASCII character for negative acknowledgement = NAK<br />
5210.0 5210.1 421 ASCII character for end of transfer = EOT<br />
1) ASCII characters are only valid for the transfer of NC programs.<br />
2) If these machine parameters are programmed with 0, the standard values apply.
Change language