Service Manual TNC 407 / TNC 415 - heidenhain - DR. JOHANNES ...
Service Manual TNC 407 / TNC 415 - heidenhain - DR. JOHANNES ...
Service Manual TNC 407 / TNC 415 - heidenhain - DR. JOHANNES ...
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Kundendienst<br />
HEIDENHAIN<br />
<strong>DR</strong> <strong>JOHANNES</strong> HElDENHAlN GmbH<br />
D~83292Tra”nre”t~ s+(O85‘39) 31-o<br />
2. Minor Error Messages<br />
SERVICE MANUAL <strong>TNC</strong> <strong>407</strong>14 15<br />
Issue: 01.09.1995<br />
Paae 4<br />
The <strong>TNC</strong> <strong>407</strong>/<strong>415</strong> features a comprehensive integrated monitoring system to avoid input or operation errors, to<br />
locate errors and technical defects of the entire equipment I<strong>TNC</strong>, measuring system, machine tool, cables etc.).<br />
The monitoring system is a fixed component of the <strong>TNC</strong> hardware and software; it is always active when the<br />
control is switched on. If a technical defect or an operation error is detected, an error message in plain language<br />
is disoiaved on the screen.<br />
To erase minor error messages, press<br />
Further error messages are described in the<br />
-Operating <strong>Manual</strong> <strong>TNC</strong> <strong>407</strong>/<strong>415</strong><br />
-Technical <strong>Manual</strong><br />
Documentation by the machine tool manufacturer<br />
Operating Instructions FE 401 B.<br />
ERROR MESSAGE Section 1 ERROR MESSAGE I Section<br />
AXIS DOUBLE PfiOGRAMMED<br />
I INCORRECT<br />
:H POINT INACCESSIBLE<br />
m,,,uGE EXCEEDED<br />
BAUD RATE NOT POSSIBLE<br />
OPERATION PARAMETERS ERASED<br />
CYCL-PARAMETER INCORRECT<br />
13.2<br />
13.2<br />
13.2<br />
13.2<br />
14.5<br />
FAULTY<br />
RANGE DATA<br />
13.2<br />
DATA MED IUM MISSING<br />
14~5<br />
DATA MEDIUNI tlVlP I Y 14.5<br />
DATA MEDIUM WRITE-PROTECTED 14.5<br />
ROTATION NOT PERMITTED 13.2<br />
PLANE WRONGLY DEFINED 13.2<br />
LIMIT SWITCH 2.1<br />
2.1<br />
13.2<br />
ERR: 001 14.5<br />
ERR: 002 14.5<br />
FRR: flO3 14~5<br />
IERR: 004 14.5<br />
ERR: 010 14.5<br />
ERR: 012 14.5<br />
ERR: 013 14.5<br />
ERR: 014 14.5<br />
ERR: 100 14.5<br />
FRR. In7 lA.5<br />
1 ERR: 103 14.5 1<br />
ERR: 104 14.5<br />
ERR: 105 14.5<br />
ERR: 106 14.5<br />
ERR: 107 14.5<br />
ERR: 108<br />
14.5<br />
EMERGENCY STOP<br />
EXT. IN-/OUTPUT NOT READY<br />
WRONG OPERATING MODE<br />
WRONG PROGRAM DATA<br />
SCALING FACTOR NOT PERMITTED<br />
ME: TAPE END<br />
HANDWHE!EL DEFECTIVE<br />
HANDWHEEL ?<br />
17.3<br />
14.5<br />
14.5<br />
14.5<br />
13.2<br />
14.5<br />
12.3<br />
12.3<br />
PLC PROGF IAM NOT TRANSLATED<br />
2.1<br />
POSI’ TIONING ERROR 2.1<br />
PROGRAM INCOMPLETE 14.5<br />
EXCHANGE BUFFERBATTERY<br />
8.7<br />
INTERFACE!<br />
ALREADY ASSIGNED 14.5<br />
MIRRORING NOT<br />
PERMITTED 13.2<br />
RELAY EX7-.<br />
DC VOLTAGE MISSING 17.3<br />
POWER INTERRUPTED<br />
2.1<br />
EXCHANGE TOUCH PROBE BATTERY 13.2<br />
STYLUS ALREADY IN CONTACT 13.2<br />
PROBE SYSTEM NOT READY 1 13.2<br />
TIME LIMIT EXCEEDED 1 13.2
Change language