num parameter manual - Documentation CN

More documents

Recommendations

Info

5.7 Poor Signal and Encoder Channel Complementarity P26 Check Description 5 - 16 en-938818/6 Category Measurements Type 0 8-bit hexadecimal No. of words 32 Activates the encoder channel complementarity and poor signal check and assigns the timeout for filtering faults. Principle The word <strong>num</strong>ber gives the physical axis address. If the bit is a 1, the check is active. Default value: 00 Word Format Physical @ N0 l l l N1 l l l N2 l l l N31 Bit 7 ! CAUTION The check cannot be activated in P26 unless it is first declared in P25. Bit 0 Encoder channel complementarity check Poor signal check Timeout for filtering non-complementarity and poor signal faults
P10 P11 P12 P13 P25 P26 P34 P36 Filtering Timeout Bits 6 5 4 0 0 0 32 μs 0 0 1 16 μs 0 1 0 8 μs 0 1 1 4 μs 1 0 0 2 μs 1 0 1 1 μs 1 1 0 500 ns 1 1 1 250 ns REMARK: Parameter P26 is meaningless with DISC NT. Measurement en-938818/8 5 - 17 5
Page 1 and 2:
NUM PARAMETER MANUAL 0101938818/8 0
Page 3 and 4:
Table of Contents Table of Contents
Page 5 and 6:
Table of Contents 8.5 Spindle Measu
Page 7 and 8:
Table of Contents Record of Revisio
Page 9 and 10:
NUM 1020/1040/1060 Documentation St
Page 11 and 12:
Parameter Manual Foreword The machi
Page 13 and 14:
CHAPTER 9 MISCELLANEOUS FUNCTIONS C
Page 15 and 16:
Use of the Parameter Manual Tab Div
Page 17 and 18:
Parameter Definition 1 Parameter De
Page 19 and 20:
1.1 Introduction The machine parame
Page 21 and 22:
1.2.3 Decimal Words Parameter types
Page 23 and 24:
List of Machine Parameters 2 List o
Page 25 and 26:
List of Machine Parameters Paramete
Page 27 and 28:
Order of Parameter Integration 3 Or
Page 29 and 30:
3.1 Axis Declaration Declare the nu
Page 31 and 32:
Order of Parameter Integration 0 De
Page 33 and 34:
Declare the carrier and carried axe
Page 35 and 36:
Declare the direction of handwheel
Page 37 and 38:
3.3 Servo-Control Settings Declare
Page 39 and 40:
Declare the servo-control coefficie
Page 41 and 42:
Declare dynamic movement control De
Page 43 and 44:
Very high speed machining Cont’d
Page 45 and 46:
Set the maximum permissible acceler
Page 47 and 48:
Declare the axis travels Cont’d V
Page 49 and 50:
3.5 Spindle Settings 3.5.1 Spindle
Page 51 and 52:
Define the spindle 3 speed range De
Page 53 and 54:
3.5.2 Rigid Tapping Declare the spi
Page 55 and 56:
Define the minimum block execution
Page 57 and 58:
3.7 Communication Parameter Setting
Page 59 and 60:
3.8 DISC Axis Parameter Settings Se
Page 61 and 62:
P97 P2 P0 P1 P3 P5 P4 P8 P9 P14 P27
Page 63 and 64: P97 P2 P0 P1 P3 P5 P4 P8 P9 P14 P27
Page 99 and 100: P10 P11 P12 P13 P25 P26 P34 P36 Mea
Page 101 and 102: P10 P11 P12 P13 P25 P26 P34 P36 5.1
Page 105 and 106: P10 P11 P12 P13 P25 P26 P34 P36 Yie
Page 111 and 112: P10 P11 P12 P13 P25 P26 P34 P36 Pro
Page 113: P10 P11 P12 P13 P25 P26 P34 P36 Wor
Page 117 and 118: P10 P11 P12 P13 P25 P26 P34 P36 Bit
Page 119 and 120: P10 P11 P12 P13 P25 P26 P34 P36 Bit
Page 121 and 122: P10 P11 P12 P13 P25 P26 P34 P36 Exa
Page 123 and 124: P10 P11 P12 P13 P25 P26 P34 P36 5.1
Page 125 and 126: P30 P31 P32 P20 P21 P56 P22 P23 P57
Page 165 and 166:
P30 P31 P32 P20 P21 P56 P22 P23 P57
Page 167 and 168:
P30 P31 P32 P20 P21 P56 P22 P23 P57
Page 169 and 170:
P30 P31 P32 P20 P21 P56 P22 P23 P57
Page 171 and 172:
P30 P31 P32 P20 P21 P56 P22 P23 P57
Page 173 and 174:
P15 P16 P17 P18 Axis Travels 7 Axis
Page 175 and 176:
P15 P16 P17 P18 7.1 Data Tables Tra
Page 177 and 178:
P15 P16 P17 P18 Summary of the Diff
Page 179 and 180:
P15 P16 P17 P18 Axis Travels en-938
Page 181 and 182:
P15 P16 P17 P18 Example For the axi
Page 183 and 184:
P15 P16 P17 P18 Case of Encoder ORP
Page 185 and 186:
P15 P16 P17 P18 Mechanical travel E
Page 187 and 188:
P15 P16 P17 P18 Axis Travels en-938
Page 189 and 190:
P15 P16 P17 P18 7.8 Check of Homing
Page 191 and 192:
P15 P16 P17 P18 7.9 Setting the Tra
Page 193 and 194:
P6 P40 P41 P46 P47 P48 P49 P42 P43
Page 195 and 196:
P6 8.1 Data Tables Spindle Definiti
Page 197 and 198:
P6 P40 P41 P46 P47 P48 P49 P42 P43
Page 199 and 200:
P6 8.2.5 Spindle Indexing at Consta
Page 201 and 202:
P6 P40 P41 P46 P47 P48 P49 P42 P43
Page 203 and 204:
P6 Bit 7 P40 P41 P46 P47 P48 P49 P4
Page 205 and 206:
P6 Example P40 P41 P46 P47 P48 P49
Page 207 and 208:
P6 P40 P41 P46 P47 P48 P49 P42 P43
Page 209 and 210:
P6 P40 P41 P46 P47 P48 P49 P42 P43
Page 211 and 212:
P6 P40 P41 P46 P47 P48 P49 P42 P43
Page 213 and 214:
P6 P40 P41 P46 P47 P48 P49 P42 P43
Page 215 and 216:
P6 P40 P41 P46 P47 P48 P49 P42 P43
Page 217 and 218:
P6 P40 P41 P46 P47 P48 P49 P42 P43
Page 219 and 220:
P6 P40 P41 P46 P47 P48 P49 P42 P43
Page 221 and 222:
P6 P40 P41 P46 P47 P48 P49 P42 P43
Page 223 and 224:
P6 P40 P41 P46 P47 P48 P49 P42 P43
Page 225 and 226:
P6 P40 P41 P46 P47 P48 P49 P42 P43
Page 227 and 228:
P6 Word N1 Spindles This word defin
Page 229 and 230:
P7 P35 P50 P51 P58 P59 P80 P95 P96
Page 231 and 232:
P7 P35 P50 P51 P58 P59 P80 P95 P96
Page 233 and 234:
P7 P35 P50 P51 P58 P59 P80 P95 P96
Page 235 and 236:
P7 P35 P50 P51 P58 P59 P80 P95 P96
Page 237 and 238:
P7 P35 P50 P51 P58 P59 P80 P95 P96
Page 239 and 240:
P7 P35 P50 P51 P58 P59 P80 P95 P96
Page 241 and 242:
P7 P35 P50 P51 P58 P59 P80 P95 P96
Page 243 and 244:
P7 P35 P50 P51 P58 P59 P80 P95 P96
Page 245 and 246:
P7 P35 P50 P51 P58 P59 P80 P95 P96
Page 247 and 248:
P7 P35 P50 P51 P58 P59 P80 P95 P96
Page 249 and 250:
P7 P35 P50 P51 P58 P59 P80 P95 P96
Page 251 and 252:
P7 P35 P50 P51 P58 P59 P80 P95 P96
Page 253 and 254:
P7 P35 P50 P51 P58 P59 P80 P95 P96
Page 255 and 256:
P7 P35 P50 P51 P58 P59 P80 P95 P96
Page 257 and 258:
P7 P35 P50 P51 P58 P59 P80 P95 P96
Page 259 and 260:
P37 P38 P39 P84 P100 P110 P111 P112
Page 261 and 262:
P37 P38 P39 P84 P100 P110 P111 P112
Page 263 and 264:
P37 P38 P39 P84 P100 P110 P111 P112
Page 265 and 266:
P37 P38 P39 P84 P100 P110 P111 P112
Page 267 and 268:
P37 P38 P39 P84 P100 P110 P111 P112
Page 269 and 270:
P37 P38 P39 P84 P100 P110 P111 P112
Page 271 and 272:
P37 P38 P39 P84 P100 P110 P111 P112
Page 273 and 274:
P37 P38 P39 P84 P100 P110 P111 P112
Page 275 and 276:
P37 P38 P39 P84 P100 P110 P111 P112
Page 277 and 278:
P37 P38 P39 P84 P100 P110 P111 P112
Page 279 and 280:
P37 P38 P39 P84 P100 P110 P111 P112
Page 281 and 282:
Improving the Settings 11 Improving
Page 283 and 284:
11.1 Checking the Maximum Speeds Wr
Page 285 and 286:
Check the isolation between axes. T
Page 287 and 288:
11.2.2 In-Position Window Improving
Page 289 and 290:
DISC Axes 12 DISC Axes The paramete
Page 291 and 292:
Parameter Integration Tool 13 Param
Page 293 and 294:
13.1 Integration Tool on IBM PC or
Page 295 and 296:
13.2.2 Using of the Editor 13.2.2.1
Page 297 and 298:
The display page for the parameter
Page 299 and 300:
The «NB WORDS «field specifies th
Page 301 and 302:
Parameter Integration Tool The load
Page 303 and 304:
13.2.5 Check of a Parameter Table U
Page 305 and 306:
Parameter Integration Tool Example
Page 307 and 308:
A Acceleration 6-10, 6-43 Accelerat
show all

num parameter manual - Documentation CN

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?