Operator Terminal System Manual - 11276916.pdf

More documents

Recommendations

Info

I Programming 7 Graphic display and control 0 [General] tab Parameters Description Name Enter a name for the trend object. Each object must be assigned an unambiguous name. The object name must not exceed eight characters. The parameter is mandatory. Not applicable for DOP11A-20. Sample interval Time interval between data acquisition. The minimum value is 1 s. Sample count Number of values to be stored. The maximum number of values is 65534. Not applicable for DOP11A-20. Sample full limit Enter the number of samples where the Sample full signal is to be enabled. Not applicable for DOP11A-20. Sample full signal Specify a digital signal that is to be activated when the number of samples under Sample full limit has been reached. Not applicable for DOP11A-20 Enable sampling signal Digital signal that, if enabled, starts data acquisition. Acquisiton stops when the signal is reset. Parameters need not be specified. Not applicable for DOP11A-20. Erase samples signal Define a digital signal that, if enabled, deletes all trend data in the history. Not applicable for DOP11A-20. Y scale Specify whether you want the y-scale be hidden, appear left, right, or on both sides. Minimum value The minimum value on the y-axis is called from the specified register. Maximum value Maximum value on the y-axis that is read from the specified controller register. Division Specifies which scale division is used on the y-axis. Ticks Specified the interval between the displayed scale ticks. Time range Time range to be displayed in the trend diagram. Division Specifies which scale division is used on the x-axis. Ticks Specifies the interval between the displayed scale ticks. Border style Specify whether you want the object to appear with a border. Grid Specify whether you want to display a grid in the object. Scale Define a color for the scale in the object. Grid Choose an appropriate color for the grid. BG Define a background color for the object. 140 System Manual – DOP11A Operator Terminals
[Curves] tab System Manual – DOP11A Operator Terminals Programming Graphic display and control 10644AEN Parameter Description Analog signal Analog signals acquired by the object and for which the values are to be displayed. Only 16-bit numbers must be used. Color Choose the color for the corresponding curve. Offset and gain Is used for scaling the register value. See section "General parameters" on page 114. Only two curves can be used with the DOP11A-20 model. The DOP11A-20 provides realtime trend only. [Dynamics] tab The functions on this tab are explained in section "General parameters" on page 114. If you copy a block with trend data, you will have to rename the trend object. Do not use the same name for two trend objects. I 0 7 141
Page 1 and 2:
Gearmotors \ Industrial Gear Units
Page 3 and 4:
System Manual - DOP11A Operator Ter
Page 5 and 6:
ystemhandbuch 1 Important Notes Saf
Page 7 and 8:
2 Safety Notes General information
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
3.3 Unit design DOP11A-10 Part numb
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
PFP11A (PROFIBUS panel fieldbus) Sy
Page 23 and 24:
4.2 UL compliant installation Syste
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
4.7 Connection PFE11A ETHERNET opti
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
5.2 Operator terminal functions The
Page 37 and 38:
Page 39 and 40:
Configuration mode (SETUP) System M
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
6.3 Error Messages Boot error (no i
Page 51 and 52:
6.4 SEW electronics service System
Page 53 and 54:
Effective communication System Manu
Page 55 and 56:
Page 57 and 58:
HMI-Builder installation Programmin
Page 59 and 60:
Page 61 and 62:
Default settings System Manual - DO
Page 63 and 64:
Digital data (partial access) Analo
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Terminal Click on [Change]. Figure
Page 71 and 72:
Page 73 and 74:
Creating blocks with the Block Mana
Page 75 and 76:
Defining the complete block header
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Graphic block manager Opening the g
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90: Text block manager Opening the text
Page 91 and 92: System Manual - DOP11A Operator Ter
Page 95 and 96: BDTP station change I/O cross refer
Page 115 and 116: [Block manager] menu Block manager
Page 119 and 120: Font System Manual - DOP11A Operato
Page 123 and 124: Move System Manual - DOP11A Operato
Page 125 and 126: Graphic objects Static / dynamic gr
Page 127 and 128: Dynamic analog graphic objects Syst
Page 129 and 130: [General] tab System Manual - DOP11
Page 131 and 132: X = Object positioning Correct: Dra
Page 135 and 136: [General] tab [Curves] tab System M
Page 139: Trend Not applicable for DOP11A-10.
Page 143 and 144: Alarm banner Object used for displa
Page 145 and 146: Analog clock Time object for displa
Page 151 and 152: Analog numeric table System Manual
Page 153 and 154: Operating graphic blocks Selecting
Page 159 and 160: 7.5 Text-based display and control
Page 161 and 162: Text objects Dynamic text objects T
Page 163 and 164: 7.6 Transferring projects Setting u
Page 165 and 166: Parameter Description System Manual
Page 169 and 170: Communication settings System Manua
Page 179 and 180: Torque in register D101 Speed in re
Page 189 and 190: Linking blocks with alarms System M
Page 191 and 192:
Calculating the recipe size Recipe
Page 193 and 194:
Creating recipes on the terminal Sy
Page 195 and 196:
The control block looks as follows:
Page 197 and 198:
Defining passwords System Manual -
Page 199 and 200:
Printing text blocks Printing graph
Page 201 and 202:
Control codes for the printer Syste
Page 203 and 204:
Translating and editing texts in th
Page 205 and 206:
Page 207 and 208:
Multi language functions Toggling b
Page 209 and 210:
8.9 LEDs System Manual - DOP11A Ope
Page 211 and 212:
Page 213 and 214:
Using function keys to jump to bloc
Page 215 and 216:
[General] tab System Manual - DOP11
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Settings in terminal and PC Connect
Page 225 and 226:
Page 227 and 228:
Connecting a modem System Manual -
Page 229 and 230:
Init Setup string for the modem Sys
Page 231 and 232:
ETHERNET connections System Manual
Page 233 and 234:
User name Enter the user name used
Page 235 and 236:
PPP login validation method Act as
Page 237 and 238:
9.3 Network functions in the termin
Page 239 and 240:
Alarm library [ALARMS] System Manua
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Example of an HTML page with SSI an
Page 251 and 252:
Transparent mode via ETHERNET Pass-
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Sending reports by e-mail System Ma
Page 261 and 262:
Terminal controller Transparent mod
Page 263 and 264:
Access rights System Manual - DOP11
Page 265 and 266:
Technical data Keyboard Numeric key
Page 267 and 268:
10.2 Pin assignment RS-232 D-sub 9-
Page 269 and 270:
PROFIBUS DP (option card) ETHERNET
Page 271 and 272:
10.4 DOP11A-20 Rückansicht Frontan
Page 273 and 274:
10.6 DOP11A-40 Rückansicht Frontan
Page 275 and 276:
11 Appendix 11.1 Membrane keypad Au
Page 277 and 278:
11.2 Downloading the system program
Page 279 and 280:
Date format .......................
Page 281 and 282:
Connection ........................
Page 283 and 284:
Address List Germany Headquarters P
Page 285 and 286:
China Assembly Sales Service Colomb
Page 287 and 288:
Lithuania Sales Alytus UAB Irseva M
Page 289:
Spain Assembly Sales Service Sweden
Page 292:
Gearmotors \ Industrial Gear Units
show all

Operator Terminal System Manual - 11276916.pdf

Create successful ePaper yourself

Delete template?

Save as template?