Operator Terminal System Manual - 11276916.pdf

More documents

Recommendations

Info

Network Functions and Communication 9 Communication Register Description Ctrl. reg. 0 Start register for transfer data buffer The first register in the buffer area contains the total number of bytes to be transferred. The subsequent registers c ontain the transfer data. The maximum buffer size is 127 registers = 254 bytes. Ctrl. reg. 1 Command register for transfer Is set to 1 by the controller if transfer is requested. Is set to 0 by the terminal after successful transfer. Ctrl. reg. 2 Start register for receive data buffer The first register in the buffer area cont ains the total number of bytes received. The subsequent register contains the received data. The maximum buffer size is 127 registers = 254 bytes. Ctrl. reg. 3 Command register for reception Is set to 0 by the controller if it is ready to receive data. Is set to 1 by the terminal when the message is available. Will be set to -1 (FFFF), if the me ssage is missing (e. g. too short). Is set to 2 by the controller when the port buffer is to be deleted. Is set to 3 by the controller when the port buffer was cleared. The port buffer is automatically cleared when starting the unit and when changing between transparent mode and no protocol mode. The register is assigned the value 3. Ctrl. reg. 4 End code (1 or 2 bytes) in the received message. Ctrl. reg. 5 Length of the received message. The end code will be used if the register content is 0. Drag the element to the required communication port under [Setup] / [Peripherals]. Make a right mouse click to define the register that should be listed as first control register in the transfer area. This register as well as the five subsequent registers will be used as control registers. In run mode, the controller can change between no protocol mode and transparent mode / printer mode. Enter a digital signal in the dialog under the No protocol signal parameter. Register t0 Register t1 Register t2 Ctrl. reg. 0 Ctrl. reg. 1 Ctrl. reg. 2 Ctrl. reg. 3 Control block Register t0 Register r0 Send data buffer Receive data buffer Number of bytes Register r0 Number of bytes Data Register r1 Register r2 Data – – – 54250AEN 226 System Manual – DOP11A Operator Terminals – – –
Connecting a modem System Manual – DOP11A Operator Terminals Network Functions and Communication Communication Example of using no protocol mode The following example describes the use of no protocol mode in a weighing system. The following figure illustrates the communication in a block diagram. M100 M11 0 1 2 Begin of transfer Transfer complete Receive ready Wait state Send request on current weigh Current weight 54251AEN The terminal acts as master for the weighing system. It permanently queries the current weight in the weighing system. A modem is used for establishing a connection with a PC. You make the connection settings under [Setup] / [Peripherals]. Call up the dialog by selecting the [Modem] entry and use the right mouse button to click on the selection. 9 227
Page 1 and 2:
Gearmotors \ Industrial Gear Units
Page 3 and 4:
System Manual - DOP11A Operator Ter
Page 5 and 6:
ystemhandbuch 1 Important Notes Saf
Page 7 and 8:
2 Safety Notes General information
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
3.3 Unit design DOP11A-10 Part numb
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
PFP11A (PROFIBUS panel fieldbus) Sy
Page 23 and 24:
4.2 UL compliant installation Syste
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
4.7 Connection PFE11A ETHERNET opti
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
5.2 Operator terminal functions The
Page 37 and 38:
Page 39 and 40:
Configuration mode (SETUP) System M
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
6.3 Error Messages Boot error (no i
Page 51 and 52:
6.4 SEW electronics service System
Page 53 and 54:
Effective communication System Manu
Page 55 and 56:
Page 57 and 58:
HMI-Builder installation Programmin
Page 59 and 60:
Page 61 and 62:
Default settings System Manual - DO
Page 63 and 64:
Digital data (partial access) Analo
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Terminal Click on [Change]. Figure
Page 71 and 72:
Page 73 and 74:
Creating blocks with the Block Mana
Page 75 and 76:
Defining the complete block header
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Graphic block manager Opening the g
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Text block manager Opening the text
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
BDTP station change I/O cross refer
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
[Block manager] menu Block manager
Page 117 and 118:
Page 119 and 120:
Font System Manual - DOP11A Operato
Page 121 and 122:
Page 123 and 124:
Move System Manual - DOP11A Operato
Page 125 and 126:
Graphic objects Static / dynamic gr
Page 127 and 128:
Dynamic analog graphic objects Syst
Page 129 and 130:
[General] tab System Manual - DOP11
Page 131 and 132:
X = Object positioning Correct: Dra
Page 133 and 134:
Page 135 and 136:
[General] tab [Curves] tab System M
Page 137 and 138:
Page 139 and 140:
Trend Not applicable for DOP11A-10.
Page 141 and 142:
[Curves] tab System Manual - DOP11A
Page 143 and 144:
Alarm banner Object used for displa
Page 145 and 146:
Analog clock Time object for displa
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Analog numeric table System Manual
Page 153 and 154:
Operating graphic blocks Selecting
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
7.5 Text-based display and control
Page 161 and 162:
Text objects Dynamic text objects T
Page 163 and 164:
7.6 Transferring projects Setting u
Page 165 and 166:
Parameter Description System Manual
Page 167 and 168:
Page 169 and 170:
Communication settings System Manua
Page 171 and 172:
Page 173 and 174:
Page 175 and 176: System Manual - DOP11A Operator Ter
Page 179 and 180: Torque in register D101 Speed in re
Page 189 and 190: Linking blocks with alarms System M
Page 191 and 192: Calculating the recipe size Recipe
Page 193 and 194: Creating recipes on the terminal Sy
Page 195 and 196: The control block looks as follows:
Page 197 and 198: Defining passwords System Manual -
Page 199 and 200: Printing text blocks Printing graph
Page 201 and 202: Control codes for the printer Syste
Page 203 and 204: Translating and editing texts in th
Page 207 and 208: Multi language functions Toggling b
Page 209 and 210: 8.9 LEDs System Manual - DOP11A Ope
Page 213 and 214: Using function keys to jump to bloc
Page 215 and 216: [General] tab System Manual - DOP11
Page 223 and 224: Settings in terminal and PC Connect
Page 225: System Manual - DOP11A Operator Ter
Page 229 and 230: Init Setup string for the modem Sys
Page 231 and 232: ETHERNET connections System Manual
Page 233 and 234: User name Enter the user name used
Page 235 and 236: PPP login validation method Act as
Page 237 and 238: 9.3 Network functions in the termin
Page 239 and 240: Alarm library [ALARMS] System Manua
Page 249 and 250: Example of an HTML page with SSI an
Page 251 and 252: Transparent mode via ETHERNET Pass-
Page 259 and 260: Sending reports by e-mail System Ma
Page 261 and 262: Terminal controller Transparent mod
Page 263 and 264: Access rights System Manual - DOP11
Page 265 and 266: Technical data Keyboard Numeric key
Page 267 and 268: 10.2 Pin assignment RS-232 D-sub 9-
Page 269 and 270: PROFIBUS DP (option card) ETHERNET
Page 271 and 272: 10.4 DOP11A-20 Rückansicht Frontan
Page 273 and 274: 10.6 DOP11A-40 Rückansicht Frontan
Page 275 and 276: 11 Appendix 11.1 Membrane keypad Au
Page 277 and 278:
11.2 Downloading the system program
Page 279 and 280:
Date format .......................
Page 281 and 282:
Connection ........................
Page 283 and 284:
Address List Germany Headquarters P
Page 285 and 286:
China Assembly Sales Service Colomb
Page 287 and 288:
Lithuania Sales Alytus UAB Irseva M
Page 289:
Spain Assembly Sales Service Sweden
Page 292:
Gearmotors \ Industrial Gear Units
show all

Operator Terminal System Manual - 11276916.pdf

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?