Operator Terminal System Manual - 11276916.pdf

More documents

Recommendations

Info

Network Functions and Communication 9 Network services Sending alarms by e-mail Alarms can not only be printed but can also be sent by e-mail. You can transfer the entire alarm list by sending block 990 (see section "Sending reports by e-mail"). Each alarm can be linked to one or several e-mail addresses in the configuration of the STMP client. You can make a general setting for the status of alarms for being sent by e-mail under [Setup] / [Alarm settings]. See section "Alarm handling" on page 248. 10806AEN Parameter Description Info block If an info block is specified that is a text block, the info block will be included in the e-mail. See section "Alarm handling" on page 248. Mail to address Define the mail recipient. You can choose up to eight recipients from the predefined list in the [Setup STMP Client Service] dialog. 258 System Manual – DOP11A Operator Terminals
Sending reports by e-mail System Manual – DOP11A Operator Terminals Network Functions and Communication Network services Text blocks can not only be printed but can also be sent by e-mail. Alarm block 990 can also be sent as e-mail. Only text blocks can be sent. Alarm block 990 is the only system block that can be sent as e-mail. Trend and recipe files can be sent as attachment to the e-mail message. There are restrictions when using Unicode. For further information, refer to chapter 8.8 "Unicode". 10807AEN Parameter Description Block name The name of the text block will be sent as subject if you enter the name of a text block in this field. Send mail signal An e-mail will be sent when the specified digital signal is activated. Completion signal Digital signal that is output by the terminal after an e-mail has been sent. The signal is usually activated by the terminal. Selecting the [Reset] option will reset the signal when the e-mail was sent. Mail to address The e-mail address of the recipient is entered in this field. Clicking the [...] button enables you to select up to eight recipients from a list. The list with e-mail addresses is created under [Setup] / [Network] / [Services] in the [Create SMTP Client Service] dialog. Append file Enter the name of a trend or recipe file you want to attach to your mail. If a trend file and a recipe file have the same name, the trend file will be attached. The file name must not contain national special characters, such as B, Ä, Ö and Ü. 9 259
Page 1 and 2:
Gearmotors \ Industrial Gear Units
Page 3 and 4:
System Manual - DOP11A Operator Ter
Page 5 and 6:
ystemhandbuch 1 Important Notes Saf
Page 7 and 8:
2 Safety Notes General information
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
3.3 Unit design DOP11A-10 Part numb
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
PFP11A (PROFIBUS panel fieldbus) Sy
Page 23 and 24:
4.2 UL compliant installation Syste
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
4.7 Connection PFE11A ETHERNET opti
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
5.2 Operator terminal functions The
Page 37 and 38:
Page 39 and 40:
Configuration mode (SETUP) System M
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
6.3 Error Messages Boot error (no i
Page 51 and 52:
6.4 SEW electronics service System
Page 53 and 54:
Effective communication System Manu
Page 55 and 56:
Page 57 and 58:
HMI-Builder installation Programmin
Page 59 and 60:
Page 61 and 62:
Default settings System Manual - DO
Page 63 and 64:
Digital data (partial access) Analo
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Terminal Click on [Change]. Figure
Page 71 and 72:
Page 73 and 74:
Creating blocks with the Block Mana
Page 75 and 76:
Defining the complete block header
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Graphic block manager Opening the g
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Text block manager Opening the text
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
BDTP station change I/O cross refer
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
[Block manager] menu Block manager
Page 117 and 118:
Page 119 and 120:
Font System Manual - DOP11A Operato
Page 121 and 122:
Page 123 and 124:
Move System Manual - DOP11A Operato
Page 125 and 126:
Graphic objects Static / dynamic gr
Page 127 and 128:
Dynamic analog graphic objects Syst
Page 129 and 130:
[General] tab System Manual - DOP11
Page 131 and 132:
X = Object positioning Correct: Dra
Page 133 and 134:
Page 135 and 136:
[General] tab [Curves] tab System M
Page 137 and 138:
Page 139 and 140:
Trend Not applicable for DOP11A-10.
Page 141 and 142:
[Curves] tab System Manual - DOP11A
Page 143 and 144:
Alarm banner Object used for displa
Page 145 and 146:
Analog clock Time object for displa
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Analog numeric table System Manual
Page 153 and 154:
Operating graphic blocks Selecting
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
7.5 Text-based display and control
Page 161 and 162:
Text objects Dynamic text objects T
Page 163 and 164:
7.6 Transferring projects Setting u
Page 165 and 166:
Parameter Description System Manual
Page 167 and 168:
Page 169 and 170:
Communication settings System Manua
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Torque in register D101 Speed in re
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Linking blocks with alarms System M
Page 191 and 192:
Calculating the recipe size Recipe
Page 193 and 194:
Creating recipes on the terminal Sy
Page 195 and 196:
The control block looks as follows:
Page 197 and 198:
Defining passwords System Manual -
Page 199 and 200:
Printing text blocks Printing graph
Page 201 and 202:
Control codes for the printer Syste
Page 203 and 204:
Translating and editing texts in th
Page 205 and 206:
Page 207 and 208: Multi language functions Toggling b
Page 209 and 210: 8.9 LEDs System Manual - DOP11A Ope
Page 211 and 212: System Manual - DOP11A Operator Ter
Page 213 and 214: Using function keys to jump to bloc
Page 215 and 216: [General] tab System Manual - DOP11
Page 223 and 224: Settings in terminal and PC Connect
Page 227 and 228: Connecting a modem System Manual -
Page 229 and 230: Init Setup string for the modem Sys
Page 231 and 232: ETHERNET connections System Manual
Page 233 and 234: User name Enter the user name used
Page 235 and 236: PPP login validation method Act as
Page 237 and 238: 9.3 Network functions in the termin
Page 239 and 240: Alarm library [ALARMS] System Manua
Page 249 and 250: Example of an HTML page with SSI an
Page 251 and 252: Transparent mode via ETHERNET Pass-
Page 257: System Manual - DOP11A Operator Ter
Page 261 and 262: Terminal controller Transparent mod
Page 263 and 264: Access rights System Manual - DOP11
Page 265 and 266: Technical data Keyboard Numeric key
Page 267 and 268: 10.2 Pin assignment RS-232 D-sub 9-
Page 269 and 270: PROFIBUS DP (option card) ETHERNET
Page 271 and 272: 10.4 DOP11A-20 Rückansicht Frontan
Page 273 and 274: 10.6 DOP11A-40 Rückansicht Frontan
Page 275 and 276: 11 Appendix 11.1 Membrane keypad Au
Page 277 and 278: 11.2 Downloading the system program
Page 279 and 280: Date format .......................
Page 281 and 282: Connection ........................
Page 283 and 284: Address List Germany Headquarters P
Page 285 and 286: China Assembly Sales Service Colomb
Page 287 and 288: Lithuania Sales Alytus UAB Irseva M
Page 289: Spain Assembly Sales Service Sweden
Page 292: Gearmotors \ Industrial Gear Units
show all

Operator Terminal System Manual - 11276916.pdf

Create successful ePaper yourself

Delete template?

Save as template?