TVG-Series System Guide v1-4 - SerVision
TVG-Series System Guide v1-4 - SerVision
TVG-Series System Guide v1-4 - SerVision
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>SerVision</strong><br />
<strong>TVG</strong> <strong>System</strong> <strong>Guide</strong><br />
• Field<br />
Outline Switching<br />
LAN Optimization<br />
• Description<br />
Select one of the following types of triggers for activating different outlines:<br />
• None: No automatic outline switching – outlines can only be<br />
switched manually using the configuration utility (see Defining<br />
Alternate Outlines, page 118)<br />
• Sensor: Makes it possible to use Sensor 1 events as triggers for<br />
outline switching (see Configuring Sensor and Activator Settings,<br />
page 110)<br />
Note: For CVG and CVG-M models, this option should not be selected if the<br />
sensor connector (In1) is used to control the display on a connected CCTV<br />
monitor. For additional information, please refer to the unit’s installation<br />
guide.<br />
• Schedule: Makes it possible to schedule outline switching (see<br />
Schedules, page 73)<br />
If video from the unit will be viewed primarily or exclusively on PCs that are on the<br />
same LAN as the unit, select this option to minimize the streaming delay within the<br />
LAN. That is, when this option is selected, live video will be played as close to real<br />
time as possible.<br />
Clear this option if live video will be viewed remotely via the internet or a modem<br />
connection.<br />
SMS on <strong>System</strong> Start<br />
ADAM Sensors<br />
IA Activators Used<br />
IA Sensors Used<br />
Maximum Recording<br />
Length<br />
Select this option if you want the unit to send SMS notifications whenever it starts<br />
running.<br />
If sensors are connected to the unit through an ADAM module, select Enabled.<br />
This makes it possible to activate and configure the sensors. For additional<br />
information, see Configuring Sensor and Activator Settings, page 110.<br />
If activators are connected to the unit through an IA relay board, select the number<br />
of activators that are connected to the board. For additional information, please<br />
refer to the unit’s installation guide.<br />
If sensors are connected to the unit through an IA relay board, select the number<br />
of sensors that are connected to the board. For additional information, please refer<br />
to the unit’s installation guide.<br />
If you want recorded video to be erased automatically after a specified period of<br />
time, select the desired time period. A day is defined by the system as beginning at<br />
midnight. For example, if you select “1,” the system saves all video that was<br />
recorded from midnight yesterday on. Video that was recorded before midnight<br />
yesterday is automatically erased.<br />
Note: When video is erased in this way, the storage space it occupied on the unit’s<br />
storage media is not made available for additional recordings.<br />
3. Click Update, and then save the settings. They will be implemented after the unit is restarted (see Saving<br />
Configuration Changes, page 125).<br />
Configuring Microphone and Speaker Volume<br />
The volume of attached microphones and of the internal speaker can be digitally increased or decreased by the<br />
<strong>TVG</strong>. Microphone volume can be modified to optimize the sound level of audio that is played by client software.<br />
Internal speaker volume can be adjusted to suit the location of the <strong>TVG</strong> unit and the needs of those on-site.<br />
You can choose from 11 levels of amplification. Level 5 means the volume is not modified at all. Levels 0 through<br />
4 cause the volume to be reduced (the smaller the number, the greater the reduction); levels 6 through 10 cause it to<br />
Configuring <strong>System</strong> Settings 24