1948-1952 Shop Service Manual - - Hudson-Essex-Terraplane Club

More documents

Recommendations

Info

7 - 2 CLUTCH 13. Clutch throwout bearing 14. Clutch oil seal 15. Main drive gear 16. Clutch shifter yoke 17. Clutch throwout bearing grease retainer FIGURE 3 7. Clutch engaging spring 8. Clutch engaging spring--inner 9. Clutch cover 10. Clutch cover gasket 11. Clutch cover bolts 12. Clutch collar assembly 1. Clutch driving plate assembly 2. Clutch pressure plate 3. Clutch throwout finger 4. Clutch throwout finger pin 5. Clutch throwout finger retainer 6. Clutch throwout finger retainer nut
CLUTCH 7 - 3 DRAIN AND REFILL CLUTCH The clutch assembly should be drained and refilled with Hudsonite Clutch Compound every 5000 miles as follows: 1. Remove plug (A), Figure 4, using socket wrench J-472. PROCEDURE: 1. Remove flywheel dust pan and turn fly-wheel until drain plug is at its lowest position. Remove plug and drain out the old clutch compound. 2. Turn flywheel until clutch filler hole is opposite timing opening in rear engine plate and with a filler gun, inject one pintof solvent. (20% carbon tetrachloride and 80% commercial acetone. Obtainable from drug or chemical supply houses.) FIGURE 4 2. Crank engine slowly until the star on flywheel is aligned with the timing pointer at the timing inspection hole. This will bring the drain hole to the bottom of flywheel and allow complete drainage. 3. Crank engine until the drain hole again appears at the timing inspection hole and insert 1/3 of a pintof Hudsonite Clutch Compound using J-485 Clutch Filler Gun. 4. Install plug (A). The measuring cup J-486 is calibrated and should be used for measuring the clutch compound unless the "one shot" 1/3 pint can is used. CLUTCH FLUSHING Following is the method recommended for draining and cleaning the clutches of Hudson cars in order to remove gum and oxidation deposits which cause clutch sticking. It is important that this procedure be closely followed and the engine run sufficiently to warm up the clutch parts to approximately 100° before flushing. If the parts are at a low temperature the solvent will not be effective and on the other hand, if the temperature is too high, much of it will vaporize 3. Replace plug and with a stick of the proper length o r a clutch pedal depressor, hold clutch in disengaged position. With engine at rest, permit clutch to remain disengaged for about 10 minutes. Release pedal and turn flywheel and clutch by hand approximately 1/4 turn, remaining in this position another 10 minutes. Repeat this operation depressing clutch pedal and turning flywheel 1/4 turn each time until a complete revolution is made. This will give the solvent an opportunity to act on all the internal clutch parts. 4. Drain clutch again making sure filler opening is at extreme bottom position to remove all solvent. Turn flywheel until filler opening is again exposed at the rear engine support plate. Introduce 1/3 pintof new Hudsonite compound and replace drain plug. 5. Replace flywheel dust pan. CLUTCH REMOVAL FROM CAR (Single Lever Type) 1. Remove front seat cushion. 2. Remove the four bolts attaching the bottom of front seat frame to seat track, remove two screws attaching seat adjusting lever to seat frame, and remove seat back and base from car.
Page 1 and 2:
HUDSON SHOP SERVICE MANUAL 1948 - 1
Page 3 and 4:
FORWARD I The information contained
Page 5 and 6:
ALPHABETICAL INDEX - CONTINUED III
Page 7 and 8:
ALPHABETICAL INDEX - CONTINUED V Gr
Page 9 and 10:
ALPHABETICAL INDEX - CONTINUED VII
Page 11 and 12:
LUBRICATION 1 - 1 The present day h
Page 13 and 14:
LUBRICATION 1 - 3
Page 15 and 16:
LUBRICATION 1 - 5 WATER RESISTANT L
Page 17 and 18:
LUBRICATION 1 - 7 ENGINE OILING CIR
Page 19 and 20:
LUBRICATION 1 - 9 cylinder engines.
Page 21 and 22:
ENGINE TUNE-UP 2 - 1 SECTION 2 ENGI
Page 23 and 24:
ENGINE TUNE-UP 2 -3 If a starter-ba
Page 25 and 26:
ENGINE TUNE-UP 2 -5 5. After comple
Page 27 and 28:
ENGINE TUNE-UP 2 -7 Connect one lea
Page 29 and 30:
ENGINE TUNE-UP 2 -9 BREAKER ARM SPR
Page 31 and 32:
ENGINE TUNE-UP 2 -11 VACUUM ADVANCE
Page 33 and 34:
ENGINE TUNE-UP 2 -13 3. Turn tester
Page 35 and 36:
ENGINE TUNE-UP 2 -15 FIGURE 22 CAUT
Page 37 and 38:
ENGINE TUNE-UP 2 -17 2. Connect a s
Page 39 and 40:
ENGINE TUNE-UP 2 -19 3. Pump travel
Page 41 and 42:
ENGINE TUNE-UP 2 -21 2. Hold thrott
Page 43 and 44:
ENGINE 3 - 1 ENGINE: Arrangement Co
Page 45 and 46:
ENGINE 3 - 3 VALVES: Intake Angle o
Page 47 and 48:
ENGINE 3 - 5 LUBRICATION 8 CYLINDER
Page 49 and 50:
ENGINE TUNE-UP 3 - 7 2. Inlet conne
Page 51 and 52:
ENGINE 3 - 9 NOTE: The #2 crossmemb
Page 53 and 54:
ENGINE 3 - 11 INSPECTION: 1. Remove
Page 55 and 56:
ENGINE 3 - 13 CAUTION: If the threa
Page 57 and 58:
ENGINE 3 - 15 NOTE: When Installing
Page 59 and 60:
ENGINE 3 - 17 When assembling new o
Page 61 and 62:
ENGINE 3 - 19 CAUTION: Be sure the
Page 63 and 64:
ENGINE 3 - 21 A code letter and the
Page 65 and 66:
ENGINE 3 - 23 a 3 to 4 pound pull.
Page 67 and 68:
ENGINE 3 - 25 The connecting rod be
Page 69 and 70:
ENGINE 3 - 27 Figure 32. On the 8 c
Page 71 and 72:
FIGURE 33 ENGINE 3 - 29
Page 73 and 74:
ENGINE 3 - 31 TIMING GEAR COVER OIL
Page 75 and 76:
ENGINE 3 - 33 TIMING GEAR Installat
Page 77 and 78:
ENGINE 3 - 35 REMOVAL: CAMSHAFT (8
Page 79 and 80:
ENGINE 3 - 37 18. Replace coolant a
Page 81 and 82:
FIGURE 44 ENGINE 3 - 39
Page 83 and 84:
ENGINE 3 - 41 Valve guides can be r
Page 85 and 86:
SECTION 4 FUEL SYSTEM & EXHAUST CAR
Page 87 and 88:
SECTION 4 FUEL SYSTEM & EXHAUST ENG
Page 89 and 90:
FUEL SYSTEM & EXHAUST 4 - 5 An anti
Page 91 and 92:
FUEL SYSTEM & EXHAUST 4 - 7 UNLOADE
Page 93 and 94:
FUEL SYSTEM & EXHAUST 4 - 9 6. Remo
Page 95 and 96:
FUEL SYSTEM & EXHAUST 4 - 11 5. Ins
Page 97 and 98:
FUEL SYSTEM & EXHAUST 4 - 13 18. In
Page 99 and 100:
FUEL SYSTEM & EXHAUST 4-15 CARBURET
Page 101 and 102:
FUEL SYSTEM & EXHAUST 4 - 17 2. Wit
Page 103 and 104:
FUEL SYSTEM & EXHAUST 4 - 19 6. Rem
Page 105 and 106:
FUEL SYSTEM & EXHAUST 4 - 21 7. Ins
Page 107 and 108:
FUEL SYSTEM & EXHAUST 4 - 23 FIGURE
Page 109 and 110:
FUEL SYSTEM & EXHAUST 4 - 25 NOTE:
Page 111 and 112:
TWIN CARBURETOR Installation INSTRU
Page 113 and 114:
FUEL SYSTEM & EXHAUST 4 - 29 pipe a
Page 115 and 116:
FUEL SYSTEM & EXHAUST 4 - 31 AIR CL
Page 117 and 118:
FUEL SYSTEM & EXHAUST 4 - 33 FIGURE
Page 119 and 120: FIGURE 106 FUEL SYSTEM & EXHAUST 4
Page 121 and 122: FUEL SYSTEM & EXHAUST 4 - 37 4. Dri
Page 123 and 124: FUEL SYSTEM & EXHAUST 4 - 39 GAUGE
Page 125 and 126: FUEL SYSTEM & EXHAUST 4 - 41 MANIFO
Page 127 and 128: COOLING SYSTEM 5 - 1 SECTION 5 COOL
Page 129 and 130: COOLING SYSTEM 5 - 3 2. Install rad
Page 131 and 132: COOLING SYSTEM 5 - 5 WATER PUMP - 6
Page 133 and 134: COOLING SYSTEM 5 - 7 1. Cover bolt
Page 135 and 136: COOLING SYSTEM 5 - 9 Continue heati
Page 137 and 138: ELECTRICAL SYSTEM 6 - 1 Models GENE
Page 139 and 140: ELECTRICAL SYSTEM 6 - 3 IAT-4009 IA
Page 141 and 142: ELECTRICAL SYSTEM 6 - 5 a heavy shu
Page 143 and 144: ELECTRICAL SYSTEM 6 - 7 STARTER REM
Page 145 and 146: ELECTRICAL SYSTEM 6 - 9 The generat
Page 147 and 148: ELECTRICAL SYSTEM 6 - 11 6. Remove
Page 149 and 150: ELECTRICAL SYSTEM 6 - 13
Page 151 and 152: ELECTRICAL SYSTEM 6 - 15 BRUSH REPL
Page 153 and 154: ELECTRICAL SYSTEM 6 - 17 GENERATOR
Page 155 and 156: ELECTRICAL SYSTEM 6 - 19 3. Run eng
Page 157 and 158: ELECTRICAL SYSTEM 6 - 21 screw (D)
Page 159 and 160: ELECTRICAL SYSTEM 6 - 23 Installati
Page 161 and 162: ELECTRICAL SYSTEM 6 - 25 FIGURE 23
Page 163 and 164: ELECTRICAL SYSTEM 6 - 27 FIGURE 26
Page 165 and 166: ELECTRICAL SYSTEM 6 - 29 Weather Co
Page 167 and 168: ELECTRICAL SYSTEM 6 - 31 6. If swit
Page 169: CLUTCH 7 - 1 Driving Plate Diameter
Page 173 and 174: CLUTCH 7 - 5 2. Loosen the propelle
Page 175 and 176: CLUTCH 7 - 7 ENGAGING SPRINGS If cl
Page 177 and 178: CLUTCH 7 - 9 3. Tighten the cap scr
Page 179 and 180: TRANSMISSION 8 - 1 SECTION 8 TRANSM
Page 181 and 182: TRANSMISSION 8 - 3 1. Gear Pilot Be
Page 183 and 184: TRANSMISSION 8 - 5 3. Remove govern
Page 185 and 186: TRANSMISSION 8 - 7 washer, and two
Page 187 and 188: TRANSMISSION 8 - 9 open, clean and
Page 189 and 190: TRANSMISSION 8 - 11 towards gear th
Page 191 and 192: TRANSMISSION 8 - 13 2. Place second
Page 193 and 194: TRANSMISSION 8 - 15 Worn, rough mai
Page 195 and 196: TRANSMISSION 8 - 17 NOTE: Check shi
Page 197 and 198: TRANSMISSION 8 - 19 SECTION 8 TRANS
Page 199 and 200: TRANSMISSION 8 - 21 1. Synchronizer
Page 201 and 202: TRANSMISSION 8 - 23 8. Make a dummy
Page 203 and 204: TRANSMISSION 8 - 25 center of the c
Page 205 and 206: TRANSMISSION 8 - 27 case, entering
Page 207 and 208: TRANSMISSION 8 - 29 REMOVAL AND Ins
Page 209 and 210: OVERDRIVE 9 - 1
Page 211 and 212: OVERDRIVE 9 - 3 NOTE: Unless otherw
Page 213 and 214: OVERDRIVE 9 - 5 speed of the latter
Page 215 and 216: FIGURE 10 OVERDRIVE 9 - 7
Page 217 and 218: OVERDRIVE 9 - 9 CONTROL SWITCH The
Page 219 and 220: OVERDRIVE 9 - 11 4. Remove the reta
Page 221 and 222:
OVERDRIVE 9 - 13 Installation OF AD
Page 223 and 224:
OVERDRIVE 9 - 15 3. Install the rin
Page 225 and 226:
OVERDRIVE 9 - 17 8. Remove the gove
Page 227 and 228:
OVERDRIVE 9 - 19 8. Install synchro
Page 229 and 230:
OVERDRIVE 9 - 21 NOTE: Assemble syn
Page 231 and 232:
OVERDRIVE 9 - 23 UNIT CHECKS OVERDR
Page 233 and 234:
OVERDRIVE 9 - 25 4. Connect test la
Page 235 and 236:
OVERDRIVE 9 - 27 ELECTRICAL CONDITI
Page 237 and 238:
OVERDRIVE 9 - 29 B. Occasionally, t
Page 239 and 240:
PROPELLER SHAFT 10 - 1 Front Shaft
Page 241 and 242:
PROPELLER SHAFT 10 - 3 5. Tap on th
Page 243 and 244:
REAR AXLE 11 - 1 SECTION 11 REAR AX
Page 245 and 246:
REAR AXLE 11 - 3 FIGURE 2 31. Diffe
Page 247 and 248:
REAR AXLE 11 - 5 8. Loosen nuts (1)
Page 249 and 250:
REAR AXLE 11 - 7 3. Place the head
Page 251 and 252:
REAR AXLE 11 - 9 3. Remove the thre
Page 253 and 254:
REAR AXLE 11 - 11 FIGURE 24 2. Plac
Page 255 and 256:
REAR AXLE 11 - 13 6. Install bearin
Page 257 and 258:
REAR AXLE 11 - 15 9. Place axle sha
Page 259 and 260:
REAR AXLE 11 - 17 DESCRIPTION This
Page 261 and 262:
REAR AXLE 11 - 19 FIGURE 36 LEGEND
Page 263 and 264:
REAR AXLE 11 - 21 4. Remove bolt s
Page 265 and 266:
REAR AXLE 11 - 23 5. If drive gear
Page 267 and 268:
REAR AXLE 11 - 25 18. If the microm
Page 269 and 270:
FRONT SUSPENSION 12 - 1 Curb height
Page 271 and 272:
FRONT SUSPENSION 12 - 3 FIGURE 2 1.
Page 273 and 274:
FRONT SUSPENSION 12 - 5 LOWER SUPPO
Page 275 and 276:
FRONT SUSPENSION 12 -7 plus not mor
Page 277 and 278:
FRONT SUSPENSION 12 - 9 the relief
Page 279 and 280:
FRONT SUSPENSION 12 - 11 Figure 17,
Page 281 and 282:
FRONT SUSPENSION 12 - 13 CAUSE: EXC
Page 283 and 284:
FRONT SUSPENSION 12 - 15 NOTE: Whee
Page 285 and 286:
FRONT SUSPENSION 12 - 17 PITMAN ARM
Page 287 and 288:
STEERING GEAR 13 - 1 Type Ratios -
Page 289 and 290:
STEERING GEAR 13 - 3 FIGURE 1 Steer
Page 291 and 292:
STEERING GEAR 13 - 5 5. Apply a sma
Page 293 and 294:
STEERING GEAR 13 - 7 install worm a
Page 295 and 296:
STEERING GEAR 13 - 9 FIGURE 8 ADJUS
Page 297 and 298:
STEERING GEAR 13 - 11 5. Tighten ro
Page 299 and 300:
SPRINGS, SHOCK ABSORBERS, & STABILI
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
BRAKES 15 - 1 SECTION 15 BRAKES SPE
Page 309 and 310:
BRAKES 15 - 3 It is necessary that
Page 311 and 312:
BRAKES 15 - 5 WHEEL CYLINDERS (FRON
Page 313 and 314:
BRAKES 15 - 7 DISASSEMBLING REAR BR
Page 315 and 316:
BRAKES 15 - 9 To adjust; remove the
Page 317 and 318:
BRAKES 15 - 11 Check parking brake
Page 319 and 320:
BRAKES 15 - 13 NOTE: To reduce the
Page 321 and 322:
BRAKES 15 - 15 Remedy - 1. Replace
Page 323 and 324:
WHEELS AND TIRES 16 - 1 Tire Size 7
Page 325 and 326:
WHEELS AND TIRES 16 - 3 then anothe
Page 327 and 328:
WHEELS AND TIRES 16 - 5 Stand wheel
Page 329 and 330:
DECIMAL EQUIVALENTS 64ths 32nds 16t
show all

1948-1952 Shop Service Manual - - Hudson-Essex-Terraplane Club

Create successful ePaper yourself

Delete template?

Save as template?