1948-1952 Shop Service Manual - - Hudson-Essex-Terraplane Club
1948-1952 Shop Service Manual - - Hudson-Essex-Terraplane Club
1948-1952 Shop Service Manual - - Hudson-Essex-Terraplane Club
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
ENGINE 3 - 19<br />
CAUTION: Be sure the engine lift bracket is safely<br />
attached to the engine and that chain fall hook is properly<br />
positioned with chain tight, Figure 20, as engine<br />
will tip when the No. 3 crossmember is removed.<br />
11. Carefully remove engine out of chassis, Figure 20.<br />
Installation:<br />
1. Loosen bolts holding front motor insulators to crossmember.<br />
NOTE: This will allow proper front motor support<br />
alignment when entering motor to car.<br />
2. Enter engine to car using care to enter at a proper angle.<br />
3. Align engine with front motor support bolts, Install nuts<br />
and washers, but do not tighten at this time.<br />
4. On Hydra-Matic equipped cars, raise rear of engine<br />
sufficiently to Install the No. 3 crossmember, Install<br />
bolts but do not tighten.<br />
5. On cars equipped with standard transmissions, align rear<br />
motor support insulator with hole s in crossmember and<br />
Install spacers, flat washers, lock-washers, and nuts;<br />
tighten securely. On cars equipped with Hydra-Matic,<br />
Install the engine rear support bolts, attaching the rear<br />
insulators to the No. 3 crossmember (two each side).<br />
Tighten these bolts securely and then tighten the crossmember<br />
bolts evenly and securely.<br />
6. On cars equipped with standard transmissions, Install<br />
clutch cross shaft and bracket assembly.<br />
NOTE: Use a new rubber bushing at clutch cross shaft.<br />
7. Install clutch adjusting rod and make necessary adjustment.<br />
8. Install clutch pull back spring.<br />
9. Install the shift lever rods to transmission. On cars<br />
equipped with Hydra-Matic, Install the outer throttle<br />
rod lever, throttle rod and selector.<br />
10. Install speedometer driven gear and speedometer cable.<br />
11. Install universal joint to transmission companion<br />
flange. Lock plates securely .<br />
12. Install propeller shaft center support bracket and attaching<br />
screws.<br />
13. Install exhaust pipe flange at manifold before tightening<br />
clamp at transmission.<br />
14. Tighten front motor support bolts to 40 lbs. torque.<br />
15. Install oil pressure indicator contact (bakelite) and wire.<br />
Use care in tightening to prevent breakage.<br />
16. Install exhaust pipe clamp at rear motor support.<br />
17. Install flexible gas line.<br />
18. Refill transmission as outlined in transmission section<br />
of Hydra-Matic <strong>Manual</strong>.<br />
19. Lower car.<br />
20. Remove motor lifting bracket.<br />
21. Install oil gauge wire at check valve, coil wire, temperature<br />
gauge wire, generator wires, starter, starter c able<br />
and windshield wiper hose.<br />
22. On first series cars, Install remote control cable to<br />
control tube and attach bracket to control lever support<br />
bracket.<br />
NOTE: Shifter lever at steering wheel and transmission<br />
must be in neutral to insure proper shift.<br />
23. Install Weather Control hose at water pump tube or at<br />
water pump.<br />
24. Install air cleaner.<br />
25. Install radiator and hose.<br />
26. Attach headlight harness to junction post.<br />
27. Install front fender tie panel assembly in reverse order<br />
of removal.<br />
28. Attach hood lock release cable wire on cars so equipped.<br />
29. Install accelerator rod at throttle bell crank.<br />
30. Install hood, reverse procedure of removal.<br />
31. Refill crankcase to recommended level. See<br />
"LUBRICATION", Section 1.<br />
PISTONS. PINS. AND RINGS<br />
ROD AND PISTON REMOVAL: (6 & 8 CYLINDER)<br />
NOTE: Before removing rods and pistons, remove the<br />
ridge from the top of cylinder walls with an accredited<br />
ridge reamer.